jacking DODGE RAM 3500 GAS 2008 3.G Owners Manual

WHAT TO DO IN EMERGENCIES
CONTENTS
mHazard Warning Flasher..................416
mJacking And Tire Changing................417
NJack Location........................417
NReinstalling The Scissors-Type Jack And Tools
(1500 Models)........................419
mJacking Instructions.....................422
NRemoving The Spare Tire................422
NTire Changing Procedure................423mHoisting.............................434
mJump-Starting Procedures.................434
mFreeing A Stuck Vehicle..................437
mEmergency Tow Hooks Ð If Equipped........438
mTowing A Disabled Vehicle................439
N4-Wheel Drive Vehicles.................439
N2±Wheel Drive Vehicles.................439
6

JACKING AND TIRE CHANGING
WARNING!
²Being under a jacked-up vehicle is dangerous. The
vehicle could slip off the jack and fall on you. You
could be crushed. Never put any part of your body
under a vehicle that is on a jack. Never start or run
the engine while the vehicle is on a jack. If you need
to get under a raised vehicle, take it to an authorized
service center where it can be raised on a lift.
²The jack is designed to use as a tool for changing
tires only. The jack should not be used to lift the
vehicle for service purposes. The vehicle should
be jacked on a firm level surface only. Avoid ice or
slippery areas.
Jack Location
The jack and jack tools are stored under the front passenger
seat. Lift the flap on the side of the seat for access.
Removal (2500/3500/Mega Cab)
Remove the jack and tools by removing the wing bolt and
sliding the assembly from under the seat.
Jack Location
WHAT TO DO IN EMERGENCIES 417
6

JACKING INSTRUCTIONS
Removing The Spare Tire
Remove the spare tire before attempting to jack the truck.
Attach the wheel wrench to the jack extension tube. Insert
the tube through the access hole between the lower
tailgate and the top of the bumper and into the winch
mechanism tube. Rotate the wheel wrench handle coun-
terclockwise until the spare tire is on the ground with
enough cable slack to allow you to pull it out from under
the vehicle. When the spare is clear, tilt the retainer at the
end of the cable and pull it through the center of the
wheel.
It is recommended that you stow the flat or spare to
avoid tangling the loose cable.
NOTE:The winch mechanism is designed for use with
the jack extension tube only. Use of an air wrench or other
power tools is not recommended and can damage the
winch.
422 WHAT TO DO IN EMERGENCIES

²Block both the front and rear
of the wheel diagonally oppo-
site the jacking position. For
example, if the right front
wheel is being changed, block
the left rear wheel.
²Passengers should not remain in the vehicle when the
vehicle is being jacked.
Instructions
WARNING!
Carefully follow these tire changing warnings to help prevent
personal injury or damage to your vehicle:
²Always park on a firm, level surface as far from the edge of the
roadway as possible before raising the vehicle.
²Block the wheel diagonally opposite the wheel to be raised.
²Set the parking brake firmly and set an automatic transmis-
sion in park; a manual transmission in reverse.
²Never start or run the engine with the vehicle on a jack.
²Do not let anyone sit in the vehicle when it is on a jack.
²Do not get under the vehicle when it is on a jack.
²Only use the jack in the positions indicated and for lifting this
vehicle during a tire change.
²If working on or near a roadway, be extremely careful of motor
traffic.
²To assure that spare tires, flat or inflated are securely stowed,
spares must be stowed with the valve stem facing the ground.
²Turn on the Hazard warning flasher.
Jack Warning Label
424 WHAT TO DO IN EMERGENCIES

1. Remove the spare wheel, jack, and tools from storage.
2. Using the wheel wrench, loosen, but do not remove,
the wheel nuts by turning them counterclockwise one
turn while the wheel is still on the ground.
3. Placement of the Jack:
²For 1500 series trucks, when changing a front wheel,
place the scissors jack under the rear portion of the
lower control arm as shown below.
1500 4X2 Jacking Location
WHAT TO DO IN EMERGENCIES 425
6

²For 2500/3500 4x2 series trucks, when changing a
front wheel, place the bottle jack under the frame
rail behind the wheel. Locate the jack as far forward
as possible on the straight part of the frame.²Operate the jack using the jack drive tube and the
wheel wrench. The tube extension, may be used, but
is not required.
1500 4X4 Jacking Location4X2 Jacking
426 WHAT TO DO IN EMERGENCIES

²For 2500/3500 4x4 series trucks, when changing the
front wheel, assemble the jack drive tube to the jack
and connect the drive tube to the extension tube.
Place the jack under the axle as close to the tire as
possible with the drive tubes extending to the front.
Connect the jack tube extension and wheel wrench.²For all trucks, when changing a rear wheel, as-
semble the jack drive tube to the jack and connect
the drive tube to the extension tube. Place the jack
under the axle between the spring and the shock
absorber with the drive tubes extending to the rear.
Rear Jacking Location (All)
WHAT TO DO IN EMERGENCIES 427
6

HOISTING
A conventional floor jack may be used at the jacking
locations. Refer to the graphics that show jacking loca-
tions. However, a floor jack or frame hoist must never be
used on any other parts or the underbody.
CAUTION!
Never use a floor jack directly under the differential
housing of a loaded truck or damage to your vehicle
may result.
JUMP-STARTING PROCEDURES
Do not attempt to push or tow your vehicle to get it
started. Vehicles equipped with an automatic transmis-
sion cannot be started this way. Pushing or towing a
vehicle equipped with a manual transmission may over-
heat and damage the catalytic converter. Also, there is a
greater risk of an accident when a vehicle is being pushed
or towed. If the vehicle has a discharged battery, booster
cables may be used to obtain a start from a booster
battery or the battery in another vehicle. This type of start
can be dangerous if done improperly, so follow this
procedure carefully.
434 WHAT TO DO IN EMERGENCIES

Electronic Stability Program............... 333
Traction Control System................. 326
Electronic Roll Mitigation (ERM)............. 332
Electronic Speed Control (Cruise Control)...... 145
Electronic Stability Program (ESP).........204,333
Electronically Shifted Transfer Case........298,306
Emergency Brake........................ 318
Emergency, In Case of
Freeing Vehicle When Stuck............... 437
Hazard Warning Flasher................. 416
Jacking............................. 423
Jump Starting......................... 434
Tow Hooks.......................... 438
Towing............................. 439
Emission Control System Maintenance......... 514
Emission Related Components.............. 457
Engine..........................444,445,446
Air Cleaner.......................... 455
Block Heater......................... 282Break-In Recommendations................ 76
Compartment Identification.........444,445,446
Coolant (Antifreeze).................... 510
Exhaust Gas Caution.................... 375
Flooded, Starting...................... 280
Fuel Requirements..................... 508
Multi-Displacement..................... 338
Oil ...........................451,508,510
Oil Filler Cap......................... 452
Oil Selection.......................452,508
Oil Synthetic......................... 453
Temperature Gauge..................... 198
Equipment Identification Plate.............. 413
Event Data Recorder...................... 60
Exhaust Gas Caution..............78,187,375,465
Exhaust System....................78,464,465
Exterior Lighting........................ 136
Fabric Care............................ 486
536 INDEX

Heated Seats........................... 131
Heater............................... 261
Heater, Engine Block..................... 282
High Beam/Low Beam Select (Dimmer) Switch . . 140
Hitches
Trailer Towing........................ 389
Hoisting.............................. 434
HomeLinkt(Garage Door Opener) Transmitter . . . 156
Hood Release.......................... 133
Hoses................................ 470
Hub Caps............................. 429
Ignition............................... 12
Key ................................. 12
Ignition Key Removal..................... 12
Illuminated Entry........................ 20
Immobilizer (Sentry Key)................... 15
Infant Restraint........................62,63
Inflation Pressure Tires.................... 357Inside Rearview Mirror.................... 86
Instrument Cluster....................194,196
Instrument Panel and Controls.............. 193
Instrument Panel Lens Cleaning............. 488
Integrated Power Module (Fuses)............ 489
Interior Appearance Care.................. 487
Interior Lights.......................... 135
Intermittent Wipers (Delay Wipers)........... 141
Introduction............................. 4
Jack Location........................... 417
Jack Operation.......................422,423
Jacking Instructions...................... 422
Jump Starting.......................... 434
Key, Programming........................ 17
Key, Replacement........................ 16
Key, Sentry (Immobilizer)................... 15
Keyless Entry System...................... 21
INDEX 539
10