instrument cluster DODGE SPRINTER 2008 2.G Owner's Manual

186 Controls in detailDriving and parking
3
Starting the engine
Gasoline engine
\1
Turn the key to position
3 in the igni-
tion lock (
\2
page 111) and release it
immediately ("touch-start" function).
The engine starts automatically.
Diesel engine
\1
Switch on the ignition (
\2
page 111).
The
q
preglow indicator lamp in
the instrument cluster comes on.
\1
As soon as the
q
preglow indica-
tor lamp goes out, turn the key to po-
sition
3 in the ignition lock and
release it as soon as the engine is
running.
\1
Warm the engine up quickly.
\1
Do not run the engine at full speed
until it has reached operating tem-
perature.iYou can start the engine without pre-
glow when the engine is warm.After a cold start
Pulling awayWarning
G
Do not downshift for additional engine
braking on a slippery surface. The drive
wheels may lose their grip and the vehicle
could skid.!
CAUTION
Only drive at high speeds once the
engine has warmed up. This protects
the engine.
When driving on slippery surfaces,
avoid spinning the drive wheels
where possible as this could damage
the drive train.
nf_BA.book Page 186 Friday, January 25, 2008 3:53 PM

242 Controls in detailAuxiliary heating/ventilation*
3
\1
Press the
æ
or
ç
button to se-
lect the desired switch-on time. The
automatic switch-on is deactivated if
the
Timer off
setting is selected.
\1
Press the
è
button.
The switch-on time is selected.
The yellow indicator lamp in
the
ö
switch comes on.
Setting the switch-on time
Operating system without steering
wheel buttons
\1
Select a switch-on time as described
under “Selecting a switch-on time”
(\2
page 240).
\1
Press the reset button on the
in-
strument cluster to set the selected
switch-on time.
The hours figure flashes and
the
”
symbol appears in the dis-
play.
\1
Set the hours using the or

am
button on the
instrument cluster.
\1
Press the reset button.
The minute display flashes.
\1
Set the minutes using the
or button.
iYou can reach the
Aux. heat.
sub-
menu via the
Settings
menu
(
\2
page 161).
iIf you turn the key to position
0 in the
ignition lock, the yellow indicator
lamp in the
ö
switch goes out af-
ter 30 minutes.
The red indicator lamp in the
ö

switch comes on when the auxiliary
heating switches on.
nf_BA.book Page 242 Friday, January 25, 2008 3:53 PM

243 Controls in detail
Auxiliary heating/ventilation*
3
Operating system with steering wheel
buttons
\1
Select a switch-on time as described
under “Selecting a switch-on time”
(\2
page 240).
\1
Press the
j
button.
The
Hours
menu appears in the dis-
play.
\1
Set the hours using the
æ

or
ç
button.
\1
Press the
j
button.
The
Minutes
menu appears in the
display.
\1
Set the minutes using the
æ

or
ç
button.
\1
Press the
è
button.
The switch-on time is set and selected.
iIf you keep the button pressed, the
values will change continuously.
To return to the standard display:\4
press and hold the button
on the
instrument cluster for
more than 1 second
\4
do not press a button for
10 seconds
iTo return to the standard display,
press the
è
or
ÿ
button re-
peatedly until the standard display
appears.
nf_BA.book Page 243 Friday, January 25, 2008 3:53 PM

250 Controls in detailDriving systems
3
1To store the current or a higher speed
2To resume the last speed stored
3To store the current speed or a lower
speed
4To deactivate cruise control
Storing the current speed
\1
Accelerate/decelerate the vehicle to
the desired speed.
\1
Move the cruise control lever briefly
upward
1
or downward
3
.
\1
Release the accelerator pedal.
Cruise control is activated.
The current speed is stored.
You cannot activate cruise control if:
\4
you are driving under 20 mph
(30 km/h)
\4
you are braking
\4
you apply the handbrake and the 7
indicator lamp in the instru-
ment cluster is lit
\4
ESP
® or ASR is intervening and the
yellow ASR/ESP
® warning lamp flas-
hes in the instrument cluster
N54.25-2925-31
iAltered vehicles from Body Manufac-
turers:
Other driving and braking systems
not described in these Operating In-
structions may affect cruise control.
Please refer to the body manufactu-
rer’s instructions for more informati-
on.
nf_BA.book Page 250 Friday, January 25, 2008 3:53 PM

253 Controls in detail
Driving systems
3 i
Cruise control is automatically deac-
tivated if:\4
you are braking
\4
you apply the handbrake and
the
7
indicator lamp in the in-
strument cluster is lit
\4
you are driving under 20 mph
(30 km/h)
\4
ESP
® or ASR is intervening and
the yellow ASR/ESP
® warning
lamp flashes in the instrument
cluster
\4
you move the selector lever to po-
sition
N while driving
\4
ESP
®, ASR or ABS has malfunc-
tioned
Parktronic system (PTS)
*
Warning
G
Parktronic is only an aid and may not de-
tect all obstacles. This system does not
relieve you of the need to pay attention.
You are always responsible for safety and
must continue to pay attention to your im-
mediate surroundings when parking and
maneuvering. Otherwise, you could en-
danger yourself and others.
Warning
G
Make sure that no persons or animals are
in the maneuvering range of the vehicle.
They could otherwise be injured.
nf_BA.book Page 253 Friday, January 25, 2008 3:53 PM

367 Operation
Tires and wheels
4
In addition to the placard also con-
sult the tire inflation pressure table
(\2
page 628).
\1
If necessary, add air to achieve the
recommended tire inflation pressu-
re.
\1
Reattach the valve cap.
\1
Repeat this procedure for each tire.
Checking tire inflation pressure elec-
tronically with the Tire Pressure Mon-
itoring System (TPMS)* (vehicles
without steering wheel buttons)
iIf you have overfilled the tire, release
tire inflation pressure by pushing the
metal stem of the valve with for ex-
ample a tip of a pen. Then recheck
the tire inflation pressure with the
tire gauge.
!
CAUTION
After inspecting or adjusting the tire
inflation pressure, always reattach
the valve cap if equipped.
This will prevent moisture and dirt
from entering the valve stem, which
could damage the valve stem.
iUSA only:
The Tire Pressure Monitoring System
(TPMS) is equipped with a combina-
tion low tire pressure/TPMS mal-
function telltale in the instrument
cluster (
\2
page 20). Depending on
how the telltale illuminates, it indi-
cates a low tire pressure condition or
a malfunction in the TPMS system it-
self:
nf_BA.book Page 367 Friday, January 25, 2008 3:53 PM

368 OperationTires and wheels
4
The TPMS only functions on wheels that
are equipped with the proper electronic
sensors. It monitors the tire inflation
pressure, as selected by the driver, in all
four tires. A warning is issued to alert
you to a decrease in pressure in one or
more of the tires. If the telltale illuminates continuous-
ly, one or more of your tires is signif-
icantly underinflated. There is no
malfunction in the TPMS.
If the telltale flashes for 60 seconds
and then stays illuminated, the TPMS
system itself is not operating proper-
ly.
iCanada only:
The Tire Pressure Monitoring System
(TPMS) is equipped with a low tire
pressure telltale in the instrument
cluster (
\2
page 20). If the telltale il-
luminates, one or more of your tires
is significantly underinflated.
Warning
G
The TPMS does not warn you against in-
correctly selected tire inflation pressure
and does not warn you when the tire pres-
sure is not properly selected for the re-
spective vehicle load. It warns you only
when the pressure of one or more tires
decreases significantly below the refer-
ence inflationpressure which was stored at the time of
calibration of the TPMS after you inflated
the tires.
Continued
nf_BA.book Page 368 Friday, January 25, 2008 3:53 PM

373 Operation
Tires and wheels
4
\1
Switch on the ignition (
\2
page 111).
\1
Press the 5menu button on the in-
strument cluster until you see the +CAL TPMS
message in the display.
\1
Press the ,menu button on the in-
strument cluster.
The following message is displayed:OK TPMSThe tire pressure monitor activation
process has begun.
The tire pressures of the individual
wheels are stored as the new refer-
ence values if they are determined to
be plausible for the tire pressure
monitor.If you wish to cancel the activation pro-
cess:
\1
Press the .button or the 5menu but-
ton on the instrument cluster.
The activation process is canceled
automatically if 30 seconds elapse
with no input.
Checking tire inflation pressure elec-
tronically with the Tire Pressure Mon-
itoring System (TPMS)* (vehicles
with steering wheel buttons)Vehicles with steering wheel buttons are
equipped with the Advanced Tire Pres-
sure Monitoring System.
iUSA only:
The Tire Pressure Monitoring System
(TPMS) is equipped with a combina-
tion low tire pressure/TPMS mal-
function telltale in the instrument
cluster (
\2
page 20). Depending on
how the telltale illuminates, it indi-
cates a low tire pressure condition or
a malfunction in the TPMS system it-
self:
If the telltale illuminates continuous-
ly, one or more of your tires is signif-
icantly underinflated. There is no
malfunction in the TPMS.
nf_BA.book Page 373 Friday, January 25, 2008 3:53 PM

374 OperationTires and wheels
4
The TPMS only functions on wheels that
are equipped with the proper electronic
sensors. It monitors the tire inflation
pressure, as selected by the driver, in all
four tires. A warning is issued to alert
you to a decrease in pressure in one or
more of the tires.
Tire pressure inquiries are made using
the multifunction display. The present
inflation pressures are displayed only af-
ter a few minutes’ travel time.
\1
Switch on the ignition (
\2
page 111).
\1
Press the
j
or
k
button until
the current inflation pressures for
each tire appear in the multifunction
display. If the telltale flashes for 60 seconds
and then stays illuminated, the TPMS
system itself is not operating proper-
ly.
iCanada only:
The Tire Pressure Monitoring System
(TPMS) is equipped with a low tire
pressure telltale in the instrument
cluster (
\2
page 20). If the telltale il-
luminates, one or more of your tires
is significantly underinflated.
iPossible differences between the
readings of a tire pressure gauge of
an air hose, e.g. gas station equip-
ment, and the vehicle’s control sys-
tem can occur. Usually the readings
issued by the control system are
more precise.
nf_BA.book Page 374 Friday, January 25, 2008 3:53 PM

460 Practical hintsWhat to do if ...
5
Indicator and warning lamps in the
instrument clusterWarning
G
Always have maintenance work carried
out at an authorized Sprinter Dealer
Continued
Warning (Continued)
G
which has the necessary specialist knowl-
edge and tools to carry out the work re-
quired.
The manufacturer recommends that you
use an authorized Sprinter Dealer for this
purpose.
Continued
Warning (Continued)
G
I n p a r t i c u l a r , w o r k r e l e v a n t t o s a f e t y o r o n
safety-related systems must be carried
out at an authorized Sprinter Dealer.
There is a risk of an accident and injury if
this work is carried out incorrectly.
nf_BA.book Page 460 Friday, January 25, 2008 3:53 PM