lights DODGE SPRINTER 2008 2.G Owners Manual
[x] Cancel search | Manufacturer: DODGE, Model Year: 2008, Model line: SPRINTER, Model: DODGE SPRINTER 2008 2.GPages: 666, PDF Size: 14.11 MB
Page 44 of 666
42 SafetyOccupant safety
2
Activation of emergency tensioning
retractors, belt force limiters and air-
bagsIn the event of a collision, the
sensor in
the airbag control unit evaluates impor-
tant physical data, such as duration, di-
rection and rate of vehicle deceleration
or acceleration. Based on the evaluation
of this data and depending on the vehi-
cle’s rate of longitudinal deceleration in
a collision, in the first stage, the airbag
control unit pre-emptively triggers the
emergency tensioning retractors.
Warning
G
A malfunction has occurred if the 1
warning lamp:d o e s n o t c o m e o n w h e n y o u s w i t c h o n t h e
ignitiondoes not go out after approximately 4 sec-
ondslights up againIndividual systems may be activated unin-
tentionally or may not be triggered in the
ev en t o f a n ac c ide n t wi th a hi gh ra te o f v e-
hicle deceleration.
Continued
Warning (Continued)
G
In this case, have the SRS system
checked and repaired immediately at a
qualified specialist workshop which has
the necessary specialist knowledge and
tools to carry out the work required.The manufacturer recommends that you
use an authorized Sprinter Dealer for this
purpose. In particular, work relevant to
safety or on safety-related systems must
be carried out at a qualified specialist
workshop.
nf_BA.book Page 42 Friday, January 25, 2008 3:53 PM
Page 47 of 666
45 Safety
Occupant safety
2
When the ignition is on, the emergency
tensioning retractor is activated:\4
only if the restraint systems are op-
erational (the
1
-warning lamp
comes on for approximately 4 sec-
onds after the ignition is switched
on.) (
\2
page 41).
\4
in the event of a head-on or rear-end
collision, if there is a high rate of ve-
hicle acceleration or deceleration in
the initial stages of a collision
\4
in the event of a side impact, if the
vehicle suddenly decelerates or ac-
celerates in a lateral direction at the
initial stage of the impact and the ve-
hicle is equipped with thorax /
sidebags and / or windowbags.If the emergency tensioning retractors
are triggered, you will hear a bang that is
generally harmless to your hearing. A
small amount of powder may also be re-
leased. The
1
warning lamp lights
up.
iEmergency tensioning retractors do
not correct:\4
incorrect sitting positions
\4
incorrectly worn seat belts
Emergency tensioning retractors do
not pull occupants back towards the
backrest.
Warning
G
If the emergency tensioning retractors
have been triggered, have them replaced
at a qualified specialist workshop which
has the necessary specialist knowledge
and tools to carry out the work required.
Continued
nf_BA.book Page 45 Friday, January 25, 2008 3:53 PM
Page 77 of 666
75 Safety
Driving safety systems
2
The ASR switch is located on the center
console.1To deactivate/activate ASR
\1To switch off:
press upper
section
1
of the switch.
The
v
warning lamp in the speed-
ometer lights up.
\1To switch on:
press upper
section
1
of the switch again.
The
v
warning lamp in the speed-
ometer goes out.
Warning
G
ESP
® remains active despite ASR having
been deactivated and carries out braking
interventions if this is necessary to im-
prove driving stability. Thev warning
lamp flashes.
If ASR is deactivated, there is an in-
creased risk that the brake system of your
vehicle could overheat and be damaged
when subjected to high loads for a long
period of time. A hot brake system also in-
creases the stopping distance.
For this reason, only deactivate ASR when
it is absolutely necessary.
N54.25-2916-31
nf_BA.book Page 75 Friday, January 25, 2008 3:53 PM
Page 81 of 666
79 Safety
Anti-theft systems
2
1To deactivate tow-away protection
2Indicator lamp
\1
Turn the key to position
0 or
1
(
\2
page 111) in the ignition lock or
remove the key.
\1
Press button
1
.
Indicator lamp2
lights up for ap-
proximately 5 seconds after the but-
ton is released.
\1
Lock the vehicle using the key.
Tow-away protection remains deactivat-
ed until you lock the vehicle again.If the anti-theft alarm system is enabled
and the vehicle is locked, a visual and
audible alarm is triggered if one of the
side windows or the rear window on your
vehicle is smashed and someone reach-
es into the interior, for example.
Enabling the interior motion sensor
\1
Close:\4
the side windows
\4
the sliding sunroof
This will prevent false alarms.
\1
Lock your vehicle.
iWhen the ignition is switched off
(\2
page 111), you cannot deactivate
tow-away protection.
Interior motion sensor*
nf_BA.book Page 79 Friday, January 25, 2008 3:53 PM
Page 82 of 666
80 SafetyAnti-theft systems
2
The interior motion sensor is enabled
after approximately 40 seconds.
Deactivating the interior motion
sensorDeactivate the interior motion sensor if
people or animals remain in the locked
vehicle. This will prevent false alarms.
The button is located in the overhead
control panel.
1To deactivate the interior motion sensor
2Indicator lamp
\1
Turn the key to position
0 or
1
(
\2
page 111) in the ignition lock or
remove the key.
\1
Press button
1
.
Indicator lamp2
lights up for ap-
proximately 5 seconds after the but-
ton is released.
iDo not leave anything (for example
mascots or coat hangers) hanging on
the rear-view mirror or on the grab
handles on the roof trim. This will pre-
vent false alarms.
iThe interior motion sensor remains
deactivated until you lock the vehicle
again.
nf_BA.book Page 80 Friday, January 25, 2008 3:53 PM
Page 98 of 666
96 Controls in detailOpening and closing
3
The indicator lamp in the switch
comes on.
or
\1
Press the locking knob of the sliding
door down (
\2
page 91).
The sliding door can jam under unfavor-
able operating conditions such as frost,
icing or heavy dirt. In this case, clean the
door entry and proceed as follows:
\1To open the sliding door:
unlock
the sliding door (
\2
page 94).
\1
Press and hold lower part
2
of the
switch on the center console or press
and hold switch
3
in the doorway.
The indicator lamp in the switch
flashes. The sliding door opens.
\1
Release the switch.
The sliding door stops.
\1To close the sliding door:
press
and hold upper part
1
of the switch
on the center console or press and
hold switch
3
in the doorway.
The indicator lamp in the switch
flashes. The sliding door closes and a
signal sounds.
\1
Release the switch. The sliding door stops.
Opening / closing using the inside
and outside door handlesObserve the notes on anti-trap protec-
tion (
\2
page 98).
1Button
iThe indicator lamp in the switch on
the center console lights up whenev-
er the sliding door is open.
N72.16-2118-31
nf_BA.book Page 96 Friday, January 25, 2008 3:53 PM
Page 107 of 666
105 Controls in detail
Opening and closing
3
1To lock / unlock the entire vehicle
2To lock / unlock the sliding doors and
rear door
The indicator lamp in the central locking
switch indicates when the sliding doors
and the rear door are locked. You can
determine whether the driver's door or
passenger's door is locked or unlocked
by the position of the locking knobs.
Locking the entire vehicle
\1
Press upper part
1
of the switch
when the doors are closed.
The indicator lamp in the switch
comes on.
Unlocking the entire vehicle
\1
Press upper part
1
of the switch.
The indicator lamp in the switch goes
out. N54.25-2917-31
iIf the key is in position
0 or no longer
in the ignition lock, the indicator
lamp in the central locking switch
lights up for 5 seconds after it is
pressed. It lights up permanently if
the key is in position
1 or
2 in the ig-
nition lock.
nf_BA.book Page 105 Friday, January 25, 2008 3:53 PM
Page 131 of 666
129 Controls in detail
Lighting
3
\3 LightingLegal requirements may impose variati-
ons in certain countries.
Your vehicle is equipped as standard
with a lamp failure monitor.
The lamp failure monitor monitors all
lamps of the exterior lighting with the ex-
ception of the identification lamps and
the trailer lighting. In the event of a lamp
failure, either the indicator lamp
.
lights up or a corresponding message
appears in the display.
iIf you are traveling in countries
where vehicles are driven on the op-
posite side of the road to that in
which the vehicle is registered, you
must have the headlamps:\4
partially masked (halogen head-
lamps)
\4
switched over (bi-xenon head-
lamps)
You will find further information in
the “Operation” section
(
\2
page 311).
Lamp failure monitor
nf_BA.book Page 129 Friday, January 25, 2008 3:53 PM
Page 133 of 666
131 Controls in detail
Lighting
3
Switching on the low-beam head-
lamps
\1
Turn light switch to
B
.
The
B
indicator lamp in the in-
strument cluster lights up.
Switching on the high-beam head-
lampsThe combination switch is located on
the left of the steering wheel.
1High-beam headlamps
2Headlamp flasher\1
Turn key to position
1 in ignition lock
(
\2
page 111).
\1
Turn light switch to
B
.
U
Automatic headlamp control*
M
Lights off
C
Parking lamps, license plate
and instrument lighting on
B
Low-beam headlamps on
N82.10-2527-31
nf_BA.book Page 131 Friday, January 25, 2008 3:53 PM
Page 134 of 666
132 Controls in detailLighting
3
\1
Press combination switch forward 1
.
The indicator lamp
A
in the in-
strument cluster lights up.
Headlamp flasher
\1
Turn key to position
1 in ignition lock
(
\2
page 111).
\1
Pull combination switch briefly in
direction
2
.
Constant headlamp mode*On vehicles with steering wheel buttons,
you can set constant headlamp mode
(\2
page 171). This does not apply to
countries in which there is a legal re-
quirement to use constant headlamp
mode.
\1
Turn light switch to
M
.
The low-beam headlamps, parking
lamps and license plate lamp are
switched on when the engine is
running.
The
B
indicator lamp in the in-
strument cluster lights up.
Automatic headlamp control*The parking lamps, low-beam head-
lamps and license plate lamp are
switched on automatically when the
brightness of ambient light falls below a
predetermined level.
nf_BA.book Page 132 Friday, January 25, 2008 3:53 PM