width DODGE SPRINTER 2008 2.G Owners Manual
[x] Cancel search | Manufacturer: DODGE, Model Year: 2008, Model line: SPRINTER, Model: DODGE SPRINTER 2008 2.GPages: 666, PDF Size: 14.11 MB
Page 121 of 666
119 Controls in detailSeats
3
Twin passenger's seat*Folding the seat cushion forward
1To release from the front anchorage
2To release from the rear anchorage\1
Lift the seat cushion out of front
anchorage
1
.
Warning
G
You could knock yourself against the un-
protected pivoting frame if the seat is oppo-
site of the direction of travel and pushed
right back in a longitudinal direction.Therefore, center the seat above the seat
base whenever you leave it. Point out this
danger to passengers.
iThe twin passenger’s seat does not
provide the same level of comfort as
the driver’s and passenger’s seats.
There is only restricted seat width
and legroom.
nf_BA.book Page 119 Friday, January 25, 2008 3:53 PM
Page 310 of 666
308 OperationDriving tips
4
Attaching a trailerPlease observe the maximum permitted
trailer dimensions (width and length).
Most states and all Canadian provinces
require safety chains between your tow
vehicle and the trailer. The chains should
be crisscrossed under the trailer tongue.
They must be attached to the hitch re-
ceiver, and not to the vehicle’s bumper
or axle. Be sure to leave enough slack in
the chains to permit turning corners.
iMost states and all Canadian prov-
inces require a separate brake sys-
tem at various trailer weights.
Warning
G
Do not connect a trailer brake system (if
trailer is so equipped) directly to the vehi-
cle’s hydraulic brake system as your vehi-
cle is equipped with antilock brakes. If
you do, neither the vehicle’s brakes nor
the trailer’s brakes will function properly.
This could cause an accident resulting in
property damage, injury or death to you or
others.The provided vehicle electrical wiring har-
ness for trailer towing has a brake signal
wire for hook-up to a brake controller.
Continued
Warning (Continued)
G
Most states and all Canadian provinces
require a break-away switch on trailers
with a separate brake system. The switch
activates the trailer brakes in the possible
event that the trailer might separate from
the tow vehicle.You should consider using a trailer sway
control system. For further information,
see your authorized Sprinter Dealer.
nf_BA.book Page 308 Friday, January 25, 2008 3:53 PM
Page 385 of 666
383 Operation
Tires and wheels
4
Tire size designation, load and speed
rating1Design standard
2Tire width
3Aspect ratio in %
4Radial tire code
5Rim diameter
6Tire load rating
7Tire speed rating
Tire sizes for Sprinter vehiclesDesign standard
Depending on the design standards
used, the tire size molded into the side
wall may have no letter or a letter
1
preceding the tire width or the tire load
rating designation.
Letter “LT” preceding the size designa-
tion:
Light Truck tire based on U.S. design
standards.
Letter “C” preceding the tire load desig-
nation:
Commercial vehicle tire based on Euro-
pean design standards.
iFor illustrative purposes only. The ac-
tual data on tires is specific to each
vehicle and may vary from the data
shown in the above illustration.
Sprinter Vehicle type
2500
LT 245/75 R 16 120/116 N
3500
LT 215/85 R 16 115/112 NLT 215/85 R 16 115/112 Q
nf_BA.book Page 383 Friday, January 25, 2008 3:53 PM
Page 386 of 666
384 OperationTires and wheels
4
Tire widthThe tire width
2
indicates the nominal
tire width in mm.
Aspect ratioThe aspect ratio
3
is the dimensional
relationship between tire section height
and section width and is expressed in
percentage. The aspect ratio is arrived
at by dividing section height by section
width.
Tire codeThe tire code
4
indicates the tire con-
struction type. The “R” stands for radial
tire type. Letter “D” means diagonal or
bias ply construction; letter “B” means
belted-bias ply construction.
Rim diameterThe rim diameter
5
is the diameter of
the bead seat, not the diameter of the
rim edge. Rim diameter is indicated in
inches (in).
Tire load ratingThe tire load rating
6
is a numerical
code associated with the maximum load
a tire can support.
For example, a load rating of 120 corre-
sponds to a maximum load of 3042 lbs
(1380 kg) the tire is designed to sup-
port.
If two values are given (as illustrated),
the first value, preceding the slash "/",
applies to single tires (rear axle). The
second value, succeeding the slash "/",
applies to twin tires (dual wheel rear ax-
le).
nf_BA.book Page 384 Friday, January 25, 2008 3:53 PM
Page 396 of 666
394 OperationTires and wheels
4
Air pressureThe amount of air inside the tire pressing
outward on each square inch of the tire.
Air pressure is expressed in pounds per
square inch (psi), or kilopascal (kPa) or
bars.Aspect ratioDimensional relationship between the
tire section height and the section width
expressed in percentage.
BarAnother metric unit for air pressure.
There are 14.5038 pounds per square
inch (psi) to 1 bar; there are
100 kilopascals (kPa) to 1 bar.BeadThe tire bead contains steel wires
wrapped by steel cords that hold the tire
onto the rim.Cold tire inflation pressureTire inflation pressure when your vehicle
has been sitting for at least 3 hours or
driven no more than 1 mile (1.6 km).
Curb weightThe weight of a motor vehicle with stan-
dard equipment including the maximum
capacity of fuel, oil, and coolant, and, if
so equipped, air conditioning and addi-
tional optional equipment, but without
passengers and cargo.DOT (D
epartment O
f T
ransportation)
A tire branding symbol which denotes
that the tire meets the requirements of
the U.S. Department of Transportation.
nf_BA.book Page 394 Friday, January 25, 2008 3:53 PM