wiring harness DODGE TRUCK 1993 Service Repair Manual

•

BRAKES
5 - 63 You must count the long flash along with the
short flashes for an accurate fault code count.

CLEARING
A
FAULT CODE
To clear a fault code, disconnect the control module
connector or disconnect the battery for a minimum of
five seconds. During system retest, wait 30 seconds
to be sure the fault code does not reappear.

FAULT
CODE

NUMBER
TYPICAL
FAILURE
DETECTED

1
Not used.
2
Open
isolation valve wiring
or
bad control
module.

3
Open
dump valve wiring
or
bad control
module.
4
Closed
RWAL
valve switch.

5
Over 16 dump pulses generated
in
2WD
vehicles (disabled
for
4WD).
6 Erratic speed sensor reading while rolling.
7 Electronic control module fuse
pellet
open,
isolation output
missing,
or
valve wiring
shorted to ground.
8
Dump
output
missing
or
valve wiring shorted
to

ground.

9
Speed
sensor wiring/resistance (usually high
reading).
10
Sensor
wiring/resistance (usually
low
reading).

11
Brake switch always on.
RWAL
light comes
on

when speed exceeds
40
mph.
12 Not used.
13 Electronic control module phase lock loop
failure.
14 Electronic control module program check
failure.
15 Electronic control module
RAM
failure.

J9005-101

Fig.
8
RWAL
System
Fault
Codes ANTILOCK COMPONENT SERVICE
GENERAL SERVICE INFORMATION
The rear wheel antilock (RWAL) components are
serviced as assemblies only. The module, hydraulic
control valve, speed sensor and exciter ring are not
repairable. These components must be replaced if di­ agnosis indicates a fault.

HYDRAULIC VALVE REPLACEMENT VALVE REMOVAL
(1) Raise vehicle.

(2)
Disconnect valve-to-sensor harness connector
(Fig. 9). (3) Disconnect brake lines connecting hydraulic
valve to rear brakes and to combination valve.
(4) Remove hydraulic valve attaching screws and
remove valve from frame bracket (Fig. 9).

VALVE INSTALLATION
(1) Start brake lines in hydraulic valve.

(2)
Position valve on frame bracket. (3) Install and tighten valve attaching nuts to
22-34 N-m (16-25 ft. lbs.) torque. (4) Tighten valve brake lines.
(5)
Bleed hydraulic valve and brakes. Refer to pro­
cedure in Service Adjustments section.
(6)
Lower vehicle.
J9005-112

Fig.
9
RWAL
Hydraulic
Valve
Attachment

5
- 64
BRAKES

•
Fig.
10
Checking
CHECKING SPEED SENSOR
AIR GAP (1) Remove sensor from differential.
(2) Measure and record distance from underside of
sensor flange to end of sensor pole piece (Fig. 10).
Distance should be 27.17 to 27.43 mm (1.07 to 1.08

in.).
This measurement represents dimension B.
(3) Measure distance between sensor mounting
surface of differential case and teeth at top of exciter
ring (Fig. 10). Distance should be 27.56 to 28.45 mm (1.085 to 1.12 in,). This distance represents dimen­
sion A.
(4) Subtract dimension B from dimension A to de­
termine sensor air gap which is dimension C (Fig.
10).
(5) Air gap should be minimum of 0.12 mm (0.005
in.) and a maximum of 1.27 mm (0.050 in.). (6) If air gap is not within stated limits, proceed
as follows: (a) Replace sensor if dimension B is not within
limits specified in step (2). (b) Replace exciter wheel or repair differential if
dimension A is not within limits specified in step
(3).
(c) Replace sensor and exciter wheel if both com­
ponents are out of tolerance.

SPEED
SENSOR REPLACEMENT
SENSOR
REMOVAL
(1) Raise vehicle on hoist.
(2) Remove bolt securing sensor to differential
housing.
(3) Remove sensor shield and sensor from differen­
tial housing. (4) Disconnect sensor wiring and remove sensor.

SENSOR
INSTALLATION
(1) Connect wires to sensor. Be sure seal is se­
curely in place between sensor and wiring con­
nector. (2) Install O-ring on sensor (if removed). (3) Insert sensor in differential housing.
SENSOR
FLANGE
DIMENSION A

-
DIMENSION
B
DIMENSION C

SENSOR
POLE
PIECE
8905-34

Sensor
Air Gap (4) Install sensor shield.
(5) Install and tighten sensor attaching bolt to
19-29 Nnn (170-230 in. lbs.).
(6) Lower vehicle.

ELECTRONIC CONTROL MODULE REPLACEMENT
The RWAL control module is at the passenger side
of the vehicle. On models with A/C, the module is at­
tached to the dash panel near the defroster duct and
resistor board (Fig. 11). To remove the module, remove the attaching
screws, disconnect the module harness connector and
remove the module. After installing the new module,
tighten the module attaching screws to 2.3 N»m (21 in. lbs.) torque.
Fig.
11
Anti-Lock
Control
Module
Mounting

7 - 20
COOLING
SYSTEM

•

HOSE
CLAMP
HOSE

J9207-36
Fig.
16
Hose
Clamp
Tool
WITH AIR
CONDITIONING
(A/C)

REMOVAL
If equipped with A/C, the generator and A/C com­
pressor along with their common mounting bracket (Fig. 17) must be partially removed. Removing the
generator or A/C compressor from their mounting
bracket is not necessary. Also, discharging the A/C system is not necessary. Do not remove any refrig­
erant lines from A/C compressor.

SUPPORT BRACKET (ROD)
GENERATOR/COMPRESSOR
MOUNTING
BRACKET

J9307-66

Fig.
17 Generator—A/C
Compressor
Mounting
Bracket—
Typical

WARNING;
THE A/C
SYSTEM
IS
UNDER
PRESSURE
EVEN
WITH
THE
ENGINE OFF. REFER
TO
REFRIG­

ERANT
WARNINGS
IN
GROUP
24,
HEATING
AND

AIR
CONDITIONING.

(1) Disconnect negative battery cable from battery. (2) Partially drain cooling system. Refer to Drain­
ing Cooling System in this group.
Do not waste reusable coolant. If the solution is
clean, drain the coolant into a clean container for re­
use.

(3) Remove upper radiator hose clamp at radiator.
Special Clamp Tool number 6094 (Fig. 16) may be
used to remove the constant tension clamps. Remove
hose at radiator.
(4) Disconnect throttle cable from clip at radiator
fan shroud. (5) Unplug wiring harness from A/C compressor.
(6) Remove the air cleaner assembly.
(7) Remove accessory drive belt. Refer to Belt Re­
moval/Installation in the Engine Accessory Drive
Belt section of this group.
(8) 3.9L/5.2L/5.9L LDC-Gas: The drive belt idler
pulley must be removed to gain access to one of the
A/C compressor/generator bracket mounting bolts. Remove the idler pulley bolt and remove idler pulley (Fig. 18).

GENERATOR/COMPRESSOR
AND
BRACKET

SUPPORT BRACKET

IGNITION

COIL
BRACKET
Fig.
18 Idler Pulley-3.9U5.2U5.9L
LDC-Gas
Engine
5.9L HDC-Gas: The automatic belt tensioner/pul-
ley assembly must be removed to gain access to one
of the A/C compressor/generator bracket mounting

bolts.
Remove the tensioner mounting bolt (Fig. 19) and remove tensioner.
(9) Remove the engine oil dipstick tube mounting
bolt at the side of the A/C-generator mounting
bracket.
(10) Disconnect throttle body control cables. Refer
to Accelerator Pedal and Throttle Cable in Group 14,
Fuel System.

7 - 22
COOLING
SYSTEM

•

Fig.
23 Bracket
Bolts—5.9L
HDC-Gas Engine
(2) Install bypass hose to engine.
(3) Secure both hose clamps.
(4) Install generator-A/C mounting bracket assem­
bly to engine. Tighten bolts (number 1 and 2 Fig. 17)
to 54 Nnn (40 ft. lbs.) torque. Tighten bracket mount­ ing bolts (Figs. 22 or 23) to 40 N-m (30 ft. lbs.)
torque.
(5) Install a new O-ring to the heater hose coolant
return tube (Figs. 20 or 21). Coat the new O-ring
with antifreeze before installation. (6) Install coolant return tube and its mounting
bolt to engine (Figs. 20 or 21). (7) Connect throttle body control cables.
(8) Install oil dipstick mounting bolt.
(9) 3.9L/5.2L/5.9L LDC-Gas: Install idler pulley.
Tighten bolt to 54 Nnn (40 ft. lbs.) torque. 5.9L HDC-Gas: Install automatic belt tensioner
assembly to mounting bracket. A dowel pin is located
on back of tensioner (Fig. 24). Align this to dowel
hole (Fig. 25) in tensioner mounting bracket. Tighten
bolt to 41 N-m (30 ft. lbs.). (10) Install drive belt. Refer to Belt Removal/In­
stallation in the Engine Accessory Drive Belt section
of this group.

CAUTION:
When installing
the
serpentine
accessory

drive belt,
the
belt must
be
routed correctly.
If not,

the engine
may
overheat
due to the
water pump
ro­

tating
in the
wrong direction. Refer
to
Belt Schemat­
ics
in the
Engine
Accessory
Drive Belt section
of

this
group
for
correct belt routing.
The
correct belt

with the
correct length must
be
used.

(11) Install air cleaner assembly.
BELT TENSIONER
DOWEL PIN
J9307-63

Fig.
24 Tensioner
Dowel
Pin—5.9L
HDC-Gas Engine Fig.
25 Tensioner
Mounting
Bracket
Dowel

Hote—5.9L
HDC-Gas Engine

(12) Install upper radiator hose to radiator.
(13) Connect throttle cable to clip at radiator fan
shroud.
(14) Connect wiring harness to A/C compressor. (15) Fill cooling system. Refer to Refilling Cooling
System in this group.
(16) Start and warm the engine. Check for leaks.

THERMOSTAT
GENERAL
INFORMATION
The thermostat on all gas powered engines is lo­
cated beneath the thermostat housing at the front of
the intake manifold (Fig. 26). The thermostat has an air bleed notch.
The thermostat of the 5.9L diesel engine is located
in the thermostat housing at front of cylinder head.
This is on exhaust manifold side of engine (Fig. 27). The thermostat is a wax pellet driven, reverse pop­
pet choke type. The wax pellet is located in a sealed container at the spring end of the thermostat. When
heated, the pellet expands, overcoming closing spring

7 - 24
COOLING SYSTEM

• If the thermostat is being replaced, be sure that
the replacement is the specified thermostat for the vehicle model and engine type. Factory installed thermostat housings on 3.9L/5.2L/
5.9L engines are installed on a gasket with an anti-
stick coating. This will aid in gasket removal and
clean-up.
(1) Disconnect negative battery cable at battery.
(2) Drain cooling system until coolant level is be­
low thermostat. Refer to Draining Cooling System in
this group. If not equipped with air conditioning, pro­ ceed to step number 4.
(3) If equipped with air conditioning: (a) Remove the support bracket (rod) located
near the rear of generator (Fig. 28).
Fig.
28
Support
Bracket—Generator
Mounting

Bracket-to-intake
Manifold—
Typical
(b) The drive belt must be removed. Refer to Belt
Removal/Installation in the Engine Accessory
Drive Belt section of this group.
(c) The generator must be partially removed. Re­
move the two generator mounting bolts. Do not re­
move any wiring at generator. If equipped with

4WD,
unplug the 4WD indicator lamp wiring har­
ness (located near rear of generator).
(d) Remove generator. Position generator to gain
access for thermostat gasket removal.
(4) Remove upper radiator hose clamp. Special
Clamp Tool number 6094 (Fig. 29) may be used to re­
move the constant tension clamps. Remove upper ra­
diator hose at thermostat housing.
(5) Position the wiring harness (behind the ther­
mostat housing) to gain access to thermostat hous­ ing.
(6) Remove thermostat housing mounting bolts,
thermostat housing, gasket and thermostat (Fig. 30). Discard old gasket.
HOSE CLAMP HOSE

J9207-36

Fig.
29
Hose
Clamp
Tool
•THERMOSTAT
MACHINED GROOVE

J9207-14

Fig.
30 Thermostat—Gas
Engines

INSTALLATION-ALL GAS
POWERED
ENGINES
(1) Clean mating areas of intake manifold and
thermostat housing. (2) Install thermostat (spring side down) into re­
cessed machined groove on intake manifold (Fig. 30).
(3) Install gasket on intake manifold and over
thermostat (Fig. 30).
(4) Position the thermostat housing to the intake
manifold. Note the word FRONT stamped on the
housing (Fig. 31). For adequate clearance, this must
be placed towards the front of vehicle. The housing should be slightly angled forward after installation
to intake manifold.
(5) Install two housing-to-intake manifold bolts.
Tighten bolts to 23 N-m (200 in. lbs.) torque.

•

ELECTRICAL
8A - 3

Fig.
3
Battery
Construction
and
Test Indicator

TEST INDICATOR
A test indicator (hydrometer) built into
the top of

the battery case, provides visual information
for
bat­
tery testing (Fig.
4). The
test indicator
is to be
used with diagnostic procedures described
in
this group.
It
is important when using
the
test indicator that
the

battery
is
relatively level
and has a
clean
top to see
correct indications.
A
light
may be
required
to
view
indicator.

WARNING:
DO
NOT USE
OPEN FLAME. EXPLOSIVE
GASES
FORM ABOVE BATTERY.
Fig.
4
Built in Test Indicator

STATE
OF
CHARGE TEST USING TEST INDICATOR
The built-in test indicator (hydrometer) measures
the specific gravity
of
the electrolyte. Specific gravity (SG)
of the
electrolyte will indicate state-of-charge
(voltage); although,
the
test indicator will
not
indi­
cate cranking capacity
of the
battery. Refer
to
Bat­
tery Load Test
for
more information. Look into
the
sight glass
and
note
the
color
of the
indicator
(Fig.

5),
refer
to the
following description
as
color indi­

cates:
GREEN-75
to
100% state-of-charge
The battery
is
adequately charged
for
more testing
or return
to use. If the
vehicle will
not
crank
for a

maximum
15
seconds, refer
to
Battery Load Test
for

more information. BLACK
OR
DARK—0
to
75% state-of-charge The battery
is
inadequately charged
and
must
be

charged until green
dot is
visible
(12.4
volts
or

greater) before
the
battery
is
tested
or
returned
to

use.
Refer
to
Causes
of
Battery Discharging
for
more information.
YELLOW
OR
BRIGHT COLOR

WARNING:
DO NOT
ATTEMPT
TO
CHARGE, TEST,
OR
ASSIST
BOOST BATTERY WHEN YELLOW
OR

BRIGHT COLOR
IS
VISIBLE. PERSONAL INJURY
MAY OCCUR.

A yellow
or
bright color indicates water (electro­
lyte) level
in
battery
is
below
the
test indicator
(Fig.
5).
Water
can not be
added
to a
maintenance free
battery.
The
battery must
be
replaced.
A low
electro­ lyte level
may be
caused
by an
over charging condi­
tion. Refer
to
Generator Test Procedures
On
Vehicle in this group.

TEST INDICATOR/STATE
OF
CHARGE

IfVW,
"TCfV

REPLACE BATTERY

lUUTu
/Otu L
f
REPLACE BATTERY

SBl
ill,
iMMiMMMMSMM^MM

GREEN BLACK

YELLOW
898A-3
Fig.
5
Test Indicator
Sight Glass

CAUSES
OF
BATTERY DISCHARGING
It
is
normal
to
have
a
small
(5 to 20
milliamperes)
draw from
the
battery with
the
ignition
in the OFF

position,
and ALL
lamps OFF.
The
constant draw
is
due
to
various electronic features
or
accessories that
require electrical current with
the
ignition
OFF to

function properly.
If a
vehicle
is not
used
for a
period of
20
days
or
more,
the
black battery disconnect
should
be
disconnected.
The
disconnect
is
located
be­

hind
the
battery
on the
engine wiring harness. This will prevent battery discharging.

ABNORMAL
BATTERY
DISCHARGING
(1) Corroded battery posts
and
terminals.
(2) Loose
or
worn generator drive belt.
(3) Electrical loads that exceed
the
output
of the

charging system
due to
equipment
or
accessories
in­
stalled after delivery. (4) Slow driving speeds (heavy traffic conditions)
or prolonged idling with high-amperage electrical systems
in use.

(5) Defective electrical circuit
or
component caus­
ing excess Ignition
Off
Draw (IOD).
(6) Defective charging system.
(7) Defective battery.

•

ELECTRICAL
8A - 9
ENGINE STARTER MOTOR TEST PROCEDURES
GENERAL INFORMATION
The starting system consists of an:
• ignition switch
• starter relay
• park/neutral position switch (automatic transmis­ sion)
• clutch switch (diesel engine-manual transmission)
• wiring harness
• battery
• starter motor with an integral solenoid. These components form 2 separate circuits. A high
amperage circuit that feeds the starter motor up to
300+ amps-gas engine; 500+ amps-diesel engine,
and a control circuit that operates on less than 20
amps (Fig. 1).
a.
BATTERY +
1
IGNITION
SWITCH 1 AUTOMATIC TRANSMISSION
•
J
NEUTRAL SAFETY SWITCH
I 4-
"JL"
MOTOR
m, ...
STA3-TERSOLENO,Dnlh
STARTER RELAY

1"

898A-14
Fig.
1 Starting
System
Components

STARTER SYSTEM DIAGNOSTIC INSPECTIONS
Before removing any unit from the starter motor
system for repair, perform the following inspections:

BATTERY
INSPECTION
To determine condition of the battery, perform the
testing procedure outlined in the Battery Section.

WIRING INSPECTION
Inspect wiring for damage. Inspect all connections
at the starter motor solenoid, park/neutral position
switch (if equipped), back-up lamp switch connector,
ignition/start switch, and battery (including all
ground connections). Clean and tighten all connec­
tions as required.

SOLENOID, RELAY
AND
IGNITION/START

SWITCH
INSPECTION
Inspect the solenoid, relay and switch to determine
their condition. Also, if equipped with automatic
transmission, inspect condition of the park/neutral position switch. Testing information can be found in
the following pages.
If the following components are working properly
remove the starter motor and follow procedures in
the Testing Section. • battery wiring
switch
solenoid
relay
park/neutral position switch

COLD CRANKING TEST
(1) Battery must first pass load and voltage drop
tests and be fully charged before proceeding. Refer to Battery Test Procedures. (2) Connect a suitable volt-ampere tester to the
battery terminals (Fig. 2). Refer to the operating in­ structions provided with the tester being used.
POSITIVE
CLAMP

898A-15
NEGATIVE
CLAMP
INDUCTION
AMPMETER
CLAMP
Fig.
2
Volt-Amps
Tester
Connections
(Typical)

(3) Fully engage parking brake, place manual
transmission in NEUTRAL, automatic transmission
in PARK. (4) Verify that all lights and accessories are OFF. (5) Remove coil secondary cable from distributor
and connect to ground.
(6) Rotate and hold the ignition switch (key) in the
START position. Note cranking voltage and amper­
age.
(a) If voltage reads above 9.6 volts and amperage
draw reads above (220 amps gas engine) (550 amps
diesel) go to Starter Feed Circuit Tests. (b) If voltage reads 12.5 volts or greater and am-
perate reads 0 to 10 amps, go to Starter Control Circuit Tests.
A cold engine will increase starter motor cur­
rent.

STARTER
FEED
CIRCUIT TESTS
-
(W0LTAGE
DROP
METHOD)
The voltage drop tests will determine if there is ex­
cessive resistance in the high current circuit. When
performing these tests, it is important that the volt­ meter be connected to the terminals that the cables are connected to instead of to the cables themselves.
For example, when testing between the battery and
solenoid, touch the voltmeter test probes to the bat-

•

IGNITION
SYSTEMS
80 - 7
DIAGNOSTICS/SERW1CE
PROCEDURES

INDEX

page

Automatic Shut Down (ASD) Relay
7
Camshaft Position
Sensor
Test
...............
7

Crankshaft Position
Sensor
Test
8

Distributor
Cap
8

Distributor
Rotor
8
Engine
Coolant Temperature
Sensor
Test
10

General
Information
7

Ignition
Coil
8

Ignition
Secondary
Circuit
Diagnosis
10

GENERAL
INFORMATION
This section
of the
group, Diagnostics/Service Pro­
cedures, will discuss basic ignition system diagnos­
tics
and
service adjustments. For system operation
and
component identification,
refer
to the
Component Identification/System Opera­
tion section
of
this group. For removal
or
installation
of
ignition system com­
ponents, refer
to the
Component Removal/Installa­
tion section
of
this group. For other useful information, refer
to
On-Board
Di­

agnostics
in the
General Diagnosis sections
of
Group
14,
Fuel System
in
this manual. For operation
of the DRB II
Diagnostic Scan Tool,
refer
to the
appropriate Powertrain Diagnostic Proce­
dures service manual.

AUTOMATIC SHUT DOWN
(ASD)
RELAY
Refer
to
Relays—Operation/Testing
in the
Group

14,
Fuel System section
of
this service manual.

CAMSHAFT POSITION SENSOR TEST
The camshaft position sensor
is
located
in the
dis­
tributor
on all
engines. To perform
a
complete test
of
this sensor
and its

circuitry, refer
to the DRB II
diagnostic scan tool.
Also refer
to the
appropriate Powertrain Diagnostics
Procedures manual.
To
test
the
sensor only, refer
to

the following: For this test,
an
analog (non-digital) voltmeter
is needed.
Do not
remove
the
distributor connector from
the
distributor. Using small paper clips, insert
them into
the
backside
of the
distributor wire har­ ness connector
to
make contact with
the
terminals.
Be sure that
the
connector
is not
damaged when
in­
serting
the
paper clips. Attach voltmeter leads
to

these paper clips. (1) Connect
the
positive (
+
)
voltmeter lead into
the sensor output wire. This
is at
done
the
distribu­ tor wire harness connector.
For
wire identification,
refer
to
Group
8W,
Wiring Diagrams.
page

Ignition
Timing
12

Intake Manifold Charge
Air
Temperature
Sensor
Test
12

Manifold Absolute Pressure (MAP)
Sensor
Test
. 12

Oxygen
Sensor
Tests
17
Powertrain Control Module (PCM)
............
14

Spark
Plug Secondary Cables
16

Spark
Plugs
............................
14

Throttle
Position
Sensor
Test
17

(2) Connect
the
negative
(-)
voltmeter lead into
the

ground wire.
For
wire identification, refer
to
Group
8W, Wiring Diagrams.
(3)
Set the
voltmeter
to the 15
Volt
DC
scale. (4) Remove distributor
cap
from distributor
(two

screws). Rotate (crank)
the
engine until
the
distribu­
tor rotor
is
pointed towards
the
rear
of
vehicle.
The

movable pulse ring should
now be
within
the
sensor
pickup.
(5) Turn ignition
key to ON
position. Voltmeter
should read approximately
5.0
volts.
(6)
If
voltage
is not
present, check
the
voltmeter
leads
for a
good connection.
(7)
If
voltage
is
still
not
present, check
for
voltage
at
the
supply wire.
For
wire identification, refer
to

Group
8W,
Wiring Diagrams.
(8)
If
voltage
is not
present
at
supply wire, check
for voltage
at
pin-7
of
powertrain control module (PCM) 60-way connector. Leave
the PCM
connector
connected
for
this test. (9)
If
voltage
is
still
not
present, perform vehicle
test using
the DRB II
diagnostic scan tool. (10)
If
voltage
is
present
at
pin-7,
but not at the

supply wire: (a) Check continuity between
the
supply wire.
This
is
checked between
the
distributor connector and pin-7
at the PCM. If
continuity
is not
present,
repair
the
harness
as
necessary. (b) Check
for
continuity between
the
camshaft
position sensor output wire
and
pin-44
at the PCM.
If continuity
is not
present, repair
the
harness
as
necessary. (c) Check
for
continuity between
the
ground cir­
cuit wire
at the
distributor connector
and
ground.
If continuity
is not
present, repair
the
harness
as
necessary. (11) While observing
the
voltmeter, crank
the en­

gine with ignition switch.
The
voltmeter needle should fluctuate between
0 and 5
volts while
the en­

gine
is
cranking. This verifies that
the
camshaft
po­
sition sensor
in the
distributor
is
operating properly
and
a
sync pulse signal
is
being generated.

8D
- 8
IGNITION
SYSTEMS

• If sync pulse signal is not present, replacement of
the camshaft position sensor is necessary. For removal or installation of ignition system com­
ponents, refer to the Component Removal/Installa­
tion section of this group.
For system operation and component identification,
refer to the Component Identification/System Opera­
tion section of this group.

CRANKSHAFT POSITION
SENSOR
TEST
To perform a complete test of this sensor and its
circuitry, refer to the DRB II diagnostic scan tool.
Also refer to the appropriate Powertrain Diagnostics
Procedures manual. To test the sensor only, refer to
the following: The sensor is located on the top of cylinder block
near the rear of right cylinder head (Fig. 1). (1) Near the rear of intake manifold, disconnect
sensor pigtail harness connector from main wiring
harness. Fig. 1 Crankshaft Position Sensor—Typical
(2) Place an ohmmeter across terminals B and C
(Fig. 2). Ohmmeter should be set to lK-to-lOK scale
for this test. The meter reading should be open (no
resistance). Replace sensor if a low resistance is indi­ cated.

DISTRIBUTOR
CAP INSPECTION Remove the distributor cap and wipe it clean with
a dry lint free cloth. Visually inspect the cap for
cracks, carbon paths, broken towers, or damaged ro­
tor button (Figs. 3 and 4). Also check for white de­
posits on the inside (caused by condensation entering VIEW LOOKING INTO

CPS
CONNECTOR
J938D-7

Fig. 2 Sensor Connector the cap through cracks). Replace any cap that dis­
plays charred or eroded terminals. The machined surface of a terminal end (faces toward rotor) will in­
dicate some evidence of erosion from normal opera­
tion. Examine the terminal ends for evidence of mechanical interference with the rotor tip. Fig. 3 Cap Inspection—External—Typical

DISTRIBUTOR ROTOR
Visually inspect the rotor (Fig. 5) for cracks, evi­
dence of corrosion, or the effects of arcing on the
metal tip. Also check for evidence of mechanical in­
terference with the cap. Some charring is normal on
the end of the metal tip. The silicone-dielectric-var­ nish-compound applied to the rotor tip for radio in­
terference noise suppression, will appear charred.
This is normal. Do not remove the charred com­ pound. Test the spring for insufficient tension. Re­
place a rotor that displays any of these adverse conditions.
IGNITION COIL

To perform a complete test of the ignition coil and
its circuitry, refer to the DRB II diagnostic scan tool.

8D
- 10
IGNITION
SYSTEMS

• Arcing at the tower will carbonize the cable boot,
which if it is connected to a new ignition coil, will cause the coil to fail. If the secondary coil cable shows any signs of dam­

age,
it should be replaced with a new cable and new
terminal. Carbon tracking on the old cable can cause
arcing and the failure of a new ignition coil.

ENGINE
COOLANT
TEMPERATURE
SENSOR
TEST
To perform a complete test of this sensor and its
circuitry, refer to the DRB II diagnostic scan tool.
Also refer to the appropriate Powertrain Diagnostics
Procedures manual. To test the sensor only, refer to
the following: The sensor is located in a water passage of the in­
take manifold next to the thermostat housing (Fig.
8).
(1) Disconnect wire harness connector from sensor
(Fig. 8). On engines with air conditioning, do not pull
directly on wiring harness. Fabricate an L-shaped
hook tool from a coat hanger (approximately eight inches long). Place the hook part of tool under the
connector for removal. The connector is snapped onto
the sensor. It is not equipped with a lock type tab.
COOLANT

TEMPERATURE
SENSOR
SENSOR RESISTANCE (OHMSJ
V

J9314-78

Fig. 8 Coolant Temperature Sensor—Typical (2) Test the resistance of the sensor with a high in­
put impedance (digital) volt-ohmmeter. The resis­ tance should be less than 1340 ohms at normal
engine operating idle temperature. For resistance
values, refer to the Sensor Resistance chart. Replace
the sensor if it is not within the range of resistance specified in the chart.
(3) Test continuity of the wire harness. This is
done between powertrain control module (PCM) wire
harness connector terminal-2 and the sensor connec­
tor terminal. Also check continuity between wire harness terminal-4 to the sensor connector terminal. Repair the wire harness if an open circuit is indi­
cated.
TEMPERATURE

RESISTANCE
(OHMS)

C
F
MIN
MAX

-40 -40 291,490 381,710
-20
-4
85,850
108,390
-10 14
49,250 61,430

0
32 29,330
35,990
10 50 17,990 21,810
20 68 11,370 13,610

25
77 9,120 10,880
30 86
7,370

8,750

40 104

4,900
5,750

50 122
3,330 3,880

60 140 2,310

2,670

70 158
1,630 1,870

80 176
1,170 1,340

90 194
860
970
100 212 640
720
110 230 480 540
120 248 370 410

J928D-4

IGNITION
SECONDARY
CIRCUIT
DIAGNOSIS

CHECKING FOR SPARK

CAUTION:
When
disconnecting a
high
voltage
cable

from
a spark
plug
or
from
the
distributor
cap,
twist
the rubber
boot
slightly
(1/2
turn)
to
break
it
loose.
Grasp
the
boot
(not the cable) and
pull
it off
with
a

steady,
even force.

(1) Disconnect the ignition coil secondary cable
from center tower of the distributor cap. Hold the ca­
ble terminal approximately 12 mm (1/2 in.) from a good engine ground (Fig. 9).
CHECK
HERE

FOR
SPARK
IGNITION

COIL
918D-18

Fig. 9 Checking for Spark—Typical