trunk DODGE VIPER 2004 ZB / 2.G User Guide

4. Manually raise the top until it meets the windshield
header (as pictured).
5. Close the trunk.6. While sitting inside the vehicle, hold onto the handles
and pull the top towards the windshield header. Push the
latch handle forward and engage the latch hook to the
windshield receiver rod.
52 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

3. Disengage the latch hook from the windshield rod
making sure to pull the latch all the way back to the
detent stow position and pull the top away from the
windshield header.
4. Open the trunk.
5. Pull the convertible top back away from the wind-
shield and all the way back to the folded position into the
storage well to the back of the seating positions. Push the
leading edge of the top down to engage the downstack
latch.
6. Finally lower and close the trunk.CONSOLE FEATURES
The front console has a removable ashtray, power outlet/
cigarette lighter and power window switches.
The center console compartment is equipped with a
cigarette lighter/power outlet and a passenger airbag
on/off switch.
54 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Trunk Ajar Light
This light indicates that the trunk is not latched.
Engine Coolant Temperature Light
A red LED light on the Coolant Temperature
gauge will illuminate to warn of an overheated
engine coolant condition.
Low Oil Pressure Light
A red LED light on the Oil Pressure gauge will
illuminate to indicate low engine oil pressure. The
light should come on briefly as a bulb check when the
engine is first started. If the light stays on or comes on
while driving, stop the vehicle and shut off the engine.
DO NOT operate the vehicle until the cause is corrected.
NOTE:This light does not indicate how much oil is in
the engine. The engine oil level must be checked under
the hood.
Charge System Light
A red LED light on the Voltage gauge will illumi-
nate when there is a charging system malfunction
or a possible accessory drive belt failure.
CAUTION!
The accessory belt also drives the water pump.
Operating the vehicle with a failed belt can cause
engine overheating and possible severe engine dam-
age.
Fog Light ON Indicator
This light indicates that the fog lights are on.
78 UNDERSTANDING YOUR INSTRUMENT PANEL

The battery is located under the battery access panel
inside the trunk on the left side. Remote battery terminals
are located in the engine compartment for jump starting.1. Wear eye protection and remove any metal jewelry
such as watch bands or bracelets that might make an
inadvertent electrical contact.
2. When boost is provided by a battery in another
vehicle, park that vehicle within booster cable reach but
WHAT TO DO IN EMERGENCIES 135
6

Maintenance-Free Battery
The top of the MAINTENANCE-FREE battery is perma-
nently sealed. You will never have to add water, nor is
periodic maintenance required.
The battery is in a compartment inside the trunk on the
left side.To service the battery:
1. Locate the battery compartment inside the trunk.
2. Remove the battery cover mounting screws and re-
move the battery cover.
3. Remove the negative battery cable post and then
remove the positive battery cable post connection.
4. Remove or loosen the battery retainer clamp and bolt.
5. Lift out the battery.
6. Clean out the battery tray area, freeing area of dirt,
stones and battery acid.
7. Clean and inspect the battery terminals and replace if
parts are damaged or unusable.
8. Place the battery in the tray.
9. Tighten the battery retainer clamp and bolt down.
156 MAINTAINING YOUR VEHICLE

Other Body Mechanisms
The following body mechanisms should be inspected
and, if necessary, all pivot and sliding contact areas of
these components should be lubricated with the lubricant
specified as follows:
Smooth White Body Lubricant - Such as Mopar Spray
White Lube:
²Hood hinge
²D/ lid hinge
²Fuel door hinge
²Lock cylinders
²Parking brake mechanism
²Trunk latches
²Ash tray
Points That Should Not Be Lubricated
There are many points that should not be lubricated;
some because they are permanently lubricated, some
because lubricants will be detrimental to the operating
characteristics, and some because lubricants will cause
component failures.
In particular, do not lubricate rubber bushings, since this
not only will cause them to fail, but will destroy their
necessary frictional characteristics.
Parts that should not be lubricated are as follows:
²Generator bearings
²Drive belt
²Accessory drive belt idler pulley
²Idler arm assembly
²Front wheel bearing
164 MAINTAINING YOUR VEHICLE

Check the battery every 4 to 6 weeks to ensure that the
voltage is above 12.40. Voltage will drop more rapidly
in hot temperatures. If battery voltage drops below
12.40, follow the battery recharge procedure in the
Service Manual.
²Check that the radiator coolant level of protection is to
at least -20ÉF (-29ÉC).
²Block the wheels. Do not apply the Parking Brake.
²Make sure that all tires are inflated to the optimum
pressure, (29 PSI).
²Cut blocks of plywood about the same size of the tires.
Cover each block with indoor/outdoor carpeting and
place them between the tires and concrete. This will
prevent tire flat spotting.
²For long term storage, remove the tires and put the
vehicle up on blocks. Stack the tires on plywood and
cover with a tarp to prevent flat spotting.
²Move the wiper blades away from the windshield.
NOTE:To help prevent the battery from discharging
during shorter periods of inactivity, perform the follow-
ing:
1. Make sure that the trunk, hood, doors, windows and
convertible top are completely closed.
2. Make sure that remote transmitter is operating and
that the battery is good.
3. Make sure that the hood, trunk and door switches are
in adjustment. Perform the quick system check which
follows.
Use the remote transmitter to set the alarm. If the alarm
SET light comes on and flashes, the system is operating
properly. If not, there is a problem with a switch or the
system. See your dealer for service.
MAINTAINING YOUR VEHICLE 185
7

Tail, Tail/Stop, and Marker Lamp Bulb
Replacement
1. Open the trunk. Remove two access panel fasteners.
Remove the access panel.
2. Twist sockets counter-clockwise to pull out bulbs.
Replace tail, tail/stop, or marker lamp bulb.3. Reinstall the appropriate bulb and socket assembly.
Replace the access panel. Close the trunk.
MAINTAINING YOUR VEHICLE 189
7

Backup and Rear Turn Signal Lamp Bulb
Replacement
1. Open the trunk. Remove two access panel fasteners.
Remove the access panel.2. Remove three plastic nuts from the upper lamp assem-
bly.
190 MAINTAINING YOUR VEHICLE

4. Replace the backup or rear turn signal lamp bulb.
Reinstall the appropriate bulb and socket assembly. Re-
install the three bulb and socket assemblies in the upper
lamp assembly. Reinstall the upper lamp assembly. Re-
place the access panel. Close the trunk.
192 MAINTAINING YOUR VEHICLE