light DODGE VIPER 2006 ZB / 2.G Workshop Manual

ONBOARD DIAGNOSTIC SYSTEM (OBD II)
To meet new government regulations and promote
cleaner air, your vehicle is equipped with a sophisticated
onboard diagnostic system called OBD II. This system
monitors the performance of the emissions and engine
control systems. When these systems are operating prop-
erly, your vehicle will provide excellent performance and
fuel economy, as well as engine emissions well within
current government regulations.
If any of these systems require service, the OBD II system
will turn on the Malfunction Indicator Light. It will also
store diagnostic codes and other information to assist
your service technician in making repairs. Although your
vehicle will usually be driveable and not need towing,
see your dealer for service as soon as possible.CAUTION!
Prolonged driving with the light on could cause
further damage to the emission control system. It
could also affect fuel economy and driveability. The
vehicle must be serviced before any state emissions
tests can be performed.
If the light is flashing, severe catalytic converter damage
and power loss will soon occur. Immediate service is
required.
If the gas cap is not tightened properly, the light may
come on. Be sure the gas cap is tightened every time you
add fuel.
MAINTAINING YOUR VEHICLE 169
7

2. Cycle the ignition from OFF to ACC four times with-
out going into ON. Leave the switch in the OFF position
after the fourth cycle.
3. Depress the driver’s side Power Door Lock switch in
the UP direction. A single chime and a horn chirp indicate
that the process has begun.4. Remove the key from the ignition and exit the vehicle.
5. The feature is cancelled when the ignition is cycled to
ON/RUN.
6. The vehicle will enter Battery Save Mode 45 seconds
after all doors are closed.
NOTE:The remote keyless entry and passenger exterior
door handle will not work when the Battery Save feature
is enabled. Enter the vehicle either by using the key to
open the door manually or by using the outside door
handle.
NOTE:The Vehicle Theft Alarm is disabled when the
vehicle is in Battery Save mode. Therefore, the vehicle is
not protected when the Battery Save feature is enabled.
NOTE:The exterior and interior lighting functions will
not work when the vehicle is in Battery Save Mode.
Exit Battery Save Mode by doing the following:
Ignition Key Positions
MAINTAINING YOUR VEHICLE 183
7

Cavity Fuse Circuits
14 Mini
Fuse 15
Amp
BlueRear 02 Sensor to Heater Relay
15 Mini
Fuse 20
Amp
YellowElectric Heated RR. WDO (EBL)
16, 17 Mini
Fuse 20
Amp
YellowFused Feed-Cigar Lighter
18 Mini
Fuse 15
Amp
BlueBatt-Locks, Power DoorCavity Fuse Circuits
19 Mini
Fuse 15
Amp
BlueBatt
20 Mini
Fuse 15
Amp
BlueFeed-Courtesy, Dome, Visor, Illu-
minated Entry, Reading
21 Mini
Fuse 15
Amp
BlueFuse Feed to Stop Lamp Switch
22 Mini
Fuse 15
Amp
BlueBattery to AC Clutch Relay
206 MAINTAINING YOUR VEHICLE

Check the battery every 4 to 6 weeks to ensure that the
voltage is above 12.40. Voltage will drop more rapidly
in hot temperatures. If battery voltage drops below
12.40, follow the battery recharge procedure in the
Service Manual.
•Check that the radiator coolant level of protection is to
at least -20°F (-29°C).
•Block the wheels. Do not apply the Parking Brake.
•Make sure that all tires are inflated to the optimum
pressure, (29 PSI).
•Cut blocks of plywood about the same size of the tires.
Cover each block with indoor/outdoor carpeting and
place them between the tires and concrete. This will
prevent tire flat spotting.
•For long term storage, remove the tires and put the
vehicle up on blocks. Stack the tires on plywood and
cover with a tarp to prevent flat spotting.
•Move the wiper blades away from the windshield.
NOTE:To help prevent the battery from discharging
during shorter periods of inactivity, perform the follow-
ing:
1. Make sure that the trunk/liftgate, hood, doors, win-
dows and convertible top are completely closed.
2. Make sure that remote transmitter is operating and
that the battery is good.
3. Make sure that the hood, trunk/liftgate and door
switches are in adjustment. Perform the quick system
check which follows.
Use the remote transmitter to set the alarm. If the alarm
SET light comes on and flashes, the system is operating
properly. If not, there is a problem with a switch or the
system. See your dealer for service.
210 MAINTAINING YOUR VEHICLE

REPLACEMENT BULBS
Interior Light Bulbs
Message Center Indicators.................. 103
Cluster................................ 103
Gauge Pack............................ 103
Heater Control........................... 37
Interior Light..........................212–2
Courtesy Footwell Lights................... 194
Exterior Light Bulbs — Convertible Models
Headlight-Low/High Beam.... Servicedatdealer only
Aux. Headlight-High Beam......... (HB3A) 9005XS
Front Park/Turn......................3157AK
Fog Light....................... (H10U)9145
Front Sidemarker.......................2886X
Center Stop Light.......... 16LED(notserviceable)
Rear Tail/Stop..........................3157
Rear Tail Light.......................... 194
Rear Marker Light........................ 194
Back up Light..........................3157
Rear Turn Light.......................3457AK
License................................ 168
NOTE:You will note that upon turning the (HID) High
Intensity Discharge Headlamp Bulbs on, there is a blue
hue to the lamps. This diminishes and becomes more
white after approximately 10 seconds as the system
charges.
MAINTAINING YOUR VEHICLE 211
7

Exterior Light Bulbs — Coupe Models
Headlight-Low/High Beam.... Servicedatdealer only
Aux. Headlight-High Beam.........(HB3A) 9005XS
Front Park/Turn......................3157AK
Fog Light.......................(H10 U) 9145
Front Sidemarker.......................2886X
Center Stop Light.......... 16LED(not serviceable)
Rear Tail/Stop/Turn.....................3157
Rear Marker Light........................ 194
Back up Light..........................3157
License................................ 168
Rear Compartment Light................... 168
NOTE:You will note that upon turning the (HID) High
Intensity Discharge Headlamp Bulbs on, there is a blue
hue to the lamps. This diminishes and becomes more
white after approximately 10 seconds as the system
charges.
EXTERIOR LIGHT BULB SERVICE
Headlight, Parking, Front Park, Turn Signal, Front
Sidemarker and Front Fog Light Removal
1. Remove the splash shield.
212 MAINTAINING YOUR VEHICLE

2. Twist off sockets counter-clockwise and pull out bulbs
from the socket, install the new bulbs, and reinstall the
bulb and socket assembly. Replace the splash shield.
NOTE:On vehicles equipped with High Intensity Dis-
charge Headlights (HID), when the headlights are turned
on there is a blue hue to the lights. This diminishes and
becomes more white after approximately 10 seconds, as
the system charges.
MAINTAINING YOUR VEHICLE 213
7

High Intensity Discharge Headlights (HID)
The headlights are a type of high voltage discharge tube.
High voltage can remain in the circuit even with the
headlight switch off and the key removed.Because of
this, you should not attempt to service a headlight bulb
yourself. If a headlight bulb fails, take your vehicle to
an authorized dealer for service.
WARNING!
A transient high tension occurs at the bulb sockets of
High Intensity Discharge (HID) headlights when the
headlight switch is turned ON. It may cause serious
electrical shock or electrocution if not serviced prop-
erly. See your authorized dealer for service.
NOTE:If High Intensity Discharge (HID) lights are not
working, recycle the headlight switch 4 times to see if it
will restrike.
Tail, Tail/Stop, and Marker Lamp Bulb
Replacement
1. Open the trunk. Remove two access panel fasteners.
Remove the access panel.
214 MAINTAINING YOUR VEHICLE

License Plate Light
Twist off sockets counter-clockwise and pull out bulbs.
Replace as required.
218 MAINTAINING YOUR VEHICLE

Headlight Aiming
The headlights on your new Viper were aimed at the
factory. The factory setting was made at a no load setting.
A great increase in weight will change the aiming and it
may be necessary to readjust the headlights if you
typically carry an excessive amount of weight in the rear
compartment or otherwise suspect misalignment.
Aiming Check
Each headlight assembly can be adjusted up and down
only. No left to right adjustment is necessary. To check,
proceed as follows:
1. Fill the fuel tank and park the vehicle on level ground.
A driveway is not normally level. If in doubt and you
have no way to check levelness, do not attempt to adjust
the headlights.2. Mark the position of the headlights on a wall prior to
loading the vehicle. Load the rear compartment with the
items you normally carry. Have someone sit in the
driver’s seat who is about the same weight as the person
who drives the vehicle.
3. Push down on the front and rear of the vehicle several
times to make sure that the suspension has settled.
4. Then readjust the headlights to the original position.
NOTE:If any further adjustments are necessary, contact
your dealership.
MAINTAINING YOUR VEHICLE 219
7