speci FIAT 500 1961 1.G Repair Manual

12:11 Folding top
The f ol di n g top assembly comprises the following
items:
1 Imitation leather top w i t h vinylite back window.
2 Front end frame complete with two handles and
catches. A movable bow which slides on the frame
guide rails.
3 Three stiffening bows fixed by chrome plated buttons
and tipped with rubber blocks.
4 Front mouldings for t o p mounting on frame.
5 Rear moulding on top mounting engine cooling air
intake body panel.
6 Retaining strap for the roller stop.
The removal of the folding top is straightforward but
care should be taken on reassembly to the vehicle and the
following points should be noted:
1 The t o p rear moulding is secured by ten screws
consisting of six self-tapping screws and four standard
screws which are located as follows:
(a) One long self-tapping screw at each end.
(b) Two standard screws at centre.
(c) Two standard screws next to the long screws.
(d) Four self-tapping screws, two on each side
between the standard screws.
These screws also secure the upper end of the engine
air intake panel to body.
2 Having fixed the rear moulding spread the top across
t h e o p e n i n g . Ensure t h e pivoting bow is located
between the second and third stiffening bows. Using
special screws fix the frame rails to the upper inner
ends of the body side panels.
12:12 Sunroof
The 'new 500' sunroof model differs from the con-
vertible model in the arrangement of the top. The sunroof
comprises a rear metal panel and a front imitation leather
covering which acts as a collapsible top.
The weather strip surrounded back window is
located
on t h e rear metal panel and the following items are
cemented in place; plastic lining, foam rubber strip at
upper front end, and two rubber welts located on the
sides to prevent water ingress.
FIG 12:14 Folded top retaining strap
F500
133 FOLDED TOP STRAP
FOLDED TOP
FIG 12:15 Arrangement of rolled top. This should be
done carefully to prevent damaging the vinylite back
window. Roll must never obstruct engine air intake slots
FOLDING TOP LOCKING HANDLES
FIG 12:16 Sun Roof top in locked position
The rear metal panel is secured to the body shell by
means of four screws, four plain washers and four spring
washers and at the rear by means of nine self-tapping
screws which provide a mounting for the engine air
intake grill and gutter.
The collapsible top comprises the following items:
1 Imitation leather lining.
2 Metal frame with a front crossmember onto which the
control handles and top front latch strikers are fitted.
A movable bow riveted to the top lining and fitted with
rubber pads which rest on t h e t o p of t h e body.
3 Front moulding for the top lining mounting onto the
framing crossmember. FOLDED TOP STRAP

BOW
FIG 12:17 Sun Roof top in unlatched position
FIG 12:18 Diagrammatic view of car heating system
Key to Fig 12 :18 1 Thermostat controlling shutter 2 Shutter, engine cooling air outlet 3 Lever, heater hand control
4 Warm air outlet slots 5 Demister valve control knobs 6 Windshield demister diffusers
NOTE—The car may be also equipped, optionally, with a heating booster as shown in FIG 12:19
134
4 Rear moulding for the top lining mounting onto the
rear metal panel.
5 Top lining retaining strap which is secured to the front
end of t h e rear metal panel using a bridge bracket.
6 Bracket for strap which hooks up the top lining when
in the folded position.
Dismantling and reassembly is a straightforward
operation providing that careful note is made of the
location of all screws that are removed. To reassemble
it is suggested that the rear metal panel is mounted on
the body shell first. The collapsible top assembly is then
positioned and secured to the rear metal panel using eight
rivets. The top covering should be stretched to the closed
position and secured to both framing side arms to t h e
body shell wells using the special screws. 500F and L
models are similar, but with a single central sun roof latch:
t h e rear metal panel is no longer removable.
12:13 Seats
Front seats:
The front bucket seats comprise a one-piece tubular
frame covered with imitation leather or cloth padded