light FIAT 500L 2017 2.G Workshop Manual

Green Telltale Indicator Lights
Turn Signal Indicator Lights
Green TelltaleLight What It Means
Turn Signal Indicator Lights
The instrument cluster directional arrow will flash independently for the left or right turn
signal as selected, as well as the exterior turn signal lamp(s) (front and rear) as selected
when the multifunction lever is moved down (left) or up (right).
NOTE:
•A continuous chime will sound if the vehicle is driven more than 1 mile (1.6 km) with
either turn signal on.
•Check for an inoperative outside light bulb if either indicator flashes at a rapid rate.
Park/Headlight On Indicator Light
Green Telltale
Light What It Means
Park/Headlight On Indicator Light
This indicator will illuminate when the park lights or headlights are turned on.
150 UNDERSTANDING YOUR INSTRUMENT PANEL

White Telltale Indicator Lights
Cruise Control Cancelled Light
White TelltaleLight What It Means
Cruise Control Cancelled Light
This light will turn on when the cruise control has been cancelled by the driver. Refer to
“Electronic Speed Control” in “Understanding The Features Of Your Vehicle” for further in-
formation.
Blue Telltale Indicator Lights
High Beam Indicator Light
Blue Telltale
Light What It Means
High Beam Indicator Light
This indicator shows that the high beam headlights are on. Push the multifunction control
lever away from you to switch the headlights to high beam. Pull the lever toward you to
switch the headlights back to low beam. Pull the lever toward you for a temporary high
beam on,
flash to pass scenario.
4
UNDERSTANDING YOUR INSTRUMENT PANEL 151

Instrument Cluster Display Setup Menu
The menu comprises a series of functions arranged in a
cycle. The menu includes the following functions:
NOTE:Some of the Menu Items could be managed by
Uconnect (if equipped). In that case, some of these are
not present in instrument cluster display.
• Dimmer
• Headlight Adj
• Speed Buzzer
• Headlamp Sensor
• Cornering Lights
• Rain Sensor
• Trip B Data
• Set Time
• Set Date
• First Page
• See Radio
• Autoclose •
Units
• Language
• Buzzer Volume
• Seat Belt Buzzer
• Service
• Passenger Airbag
• Day Lights
• Hill Start
• Tire Reset
• City Brake Control
Selecting An Option Of The Main Menu Without
Submenu
1. Briefly push and release the MENUbutton to select
the main menu option to set.
2. Push and release the upordown button (by single
pushes) to select the new setting.
3. Briefly push and release the MENUbutton to store
the new setting and go back to the main menu option
previously selected.
4
UNDERSTANDING YOUR INSTRUMENT PANEL 153

Distance Traveled
This value shows the distance covered since the last
reset.
Average Fuel Economy
This value shows the approximate average fuel con-
sumption since the last reset.
Instantaneous Fuel Economy
This indicates the fuel consumption. The value is con-
stantly updated. The message “----” will appear on the
display if the vehicle is parked with the engine running.
Average Speed
This value shows the vehicle’s average speed as a
function of the overall time elapsed since the last reset.
Travel Time
This value shows the time elapsed since the last reset.Personal Settings (Customer-Programmable
Features)
Dimmer
NOTE:The brightness of instrument panel will change
automatically only if the External Light has changed:
External Light On = Night Mode, External Light OFF =
Day Mode. In both case (Day or Night) is possible to
adjust the display brightness as described in step 1
below.
To adjust the brightness, proceed as follows:
1. Push and release the up
ordownbutton to
set the required brightness level.
2. Briefly push and release the MENUbutton to go
back to the menu screen or push and hold the MENU
(approximately one second) to go back to the main
screen without storing settings.
4
UNDERSTANDING YOUR INSTRUMENT PANEL 157

Speed Buzzer (Speed Limit)
With this function it is possible to set the car speed limit
(mph or km/h); when this limit is exceeded the driver
is immediately alerted.
To set the speed limit, proceed as follows:
1. Briefly push and release theMENUbutton. The
display will show the message (Speed Beep).
2. Push and release the up
ordownbutton to
select speed limit activation (On) or deactivation
(Off).
3. When the function is activated (On), briefly push and release the MENUbutton to display the presently set
activation speed. Pushing the up
ordown
buttons selects the speed limit. Push MENUto
confirm selection.
NOTE: Selection is possible between 20 – 125 mph or
(32 – 201 km/h), depending on the selected unit. The
setting will increase/decrease by five units each time
the up/down button is pushed. Push and hold the
up/down button to increase/decrease the setting rap-
idly. Save the setting by briefly pushing the button
when you approach the required setting. •
Briefly push and release the MENUbutton to go back
to the menu screen, or push and hold the MENU
button (approximately one second) to go back to the
main screen without storing the settings.
To cancel the setting, proceed as follows:
1. Briefly push and release the MENUbutton. “On”
will flash on the display.
2. Push and release the down
button. “Off” will
flash on the display.
3. Briefly push and release the MENUbutton to go
back to the menu screen, or push and hold the
MENU button (approximately one second) to go
back to the main screen without storing the settings.
Headlight Sensor (Automatic Headlight/Dusk
Sensor Sensitivity Adjustment)
This function is used to turn the headlights on or off
according to external light conditions.
The dusk sensor sensitivity can be adjusted according to
3 levels (level 1 = minimum sensitivity, level 2 =
medium sensitivity, level 3 = maximum sensitivity); the
greater the sensitivity set, the less the external light
158 UNDERSTANDING YOUR INSTRUMENT PANEL

variation needed to turn on the lights (e.g. with a setting
on level 3 at sunset the headlights switch on earlier than
in levels 1 and 2).
Proceed as follows to set:
1. PushMENUbutton briefly. The level set previously
flashes on the display.
2. Push the upordown button to make the adjustment.
3. Push the MENUbutton briefly to return to the menu
screen or hold the button down to return to the
standard screen without storing.
Cornering Lights (Activation/Deactivation Of
Cornering Lights)
This function activates/deactivates (On/Off) the cor-
nering lights (see the description in the “Exterior lights”
paragraph).
Proceed as follows to activate/deactivate the lights:
1. Push the MENUbutton briefly. OnorOff flash on
the display, according to what has been previously
set.
2. Push upordown to make your choice. 3. Push the
MENUbutton briefly to return to the menu
screen or hold the button down to return to the
standard screen without storing.
Rain Sensor (Rain Sensor Sensitivity Adjustment)
This function allows you to adjust the rain sensor
sensitivity to 4 levels.
To set the required sensitivity level, proceed as follows:
1. Push the MENUbutton briefly. The sensitivity
“level” set previously flashes on the display.
2. Push the upordown button to make the adjustment.
3. Push the MENUbutton briefly to return to the menu
screen or hold the button down to return to the
standard screen without storing.
Trip B Data (Trip B On)
Through this option, it is possible to activate (On) or
deactivate (Off) the Trip B (partial trip) display.
For further information, see “Trip Computer.”
For activation/deactivation, proceed as follows:
1. Briefly push and release the MENUbutton.
4
UNDERSTANDING YOUR INSTRUMENT PANEL 159

2. Push and release theupordown arrow button to
select Trip B data. Push and release the upordown
arrow button to turn ON or OFF.
3. Briefly push and release the MENUbutton to go
back to the menu screen, or push and hold the
MENU button (approximately one second) to go
back to the main screen without storing the settings.
Trip B Data Submenu Settings:
• On
• Off
• Return to MENU
Set Time (Clock)
This function may be used to set the clock through two
submenu items: “Time” and “Mode.”
Proceed as follows:
1. Briefly push and release the MENUbutton. Push and
release the up
ordownbuttons to highlight
Set Time — Push and release the MENUbutton.
2. Push and release the upordownbutton to
navigate the two sub-menu items.
3. Select the required option and then push and release the MENU button.
4. When accessing the “Time” sub-menu item, briefly push and release the MENUbutton and “hours” will
flash on the display.
5. Push and release the up
ordownbutton for
setting.
6. Briefly push and release the MENUbutton and
“minutes” will flash on the display.
7. Push and release the up
ordownbutton for
setting.
NOTE:
•The setting will increase or decrease by one unit
each time the up
ordownbutton is pushed.
Push and hold the button to increase/decrease
the setting rapidly. Save the setting by briefly
pushing the button when you approach the
required setting.
• Briefly push and release the MENUbutton to
return to the “Time” sub-function.
160 UNDERSTANDING YOUR INSTRUMENT PANEL

•When accessing the “Mode” submenu, briefly push
and release the MENUbutton. The previously set
display format will flash on the display.
• Push and release the up
ordownbutton to
select “24h” or “12h.”
When you have selected the required settings, briefly
push and release the MENUbutton to go back to the
Time, Mode sub-menu screen, or push and hold the
MENU button (approximately one second) to go back
to the main screen without storing the settings.
Set Date
This function may be used to set the date (day - month
- year).
To change, the date proceed as follows:
1. Briefly push and release the MENUbutton. Push and
release the up
ordownbutton to highlight
Date, push and release the MENUbutton and Year
will begin to flash.
2. Push and release the upordownbutton for
setting.
3. Briefly push and release the MENUbutton and
“month” will flash on the display. 4. Push and release the
up
ordownbutton for
setting.
5. Briefly push and release the MENUbutton and
“day” will flash on the display.
6. Push and release the up
ordownbutton for
setting.
NOTE: The setting will increase or decrease by one
unit each time the up
ordownbutton is
pushed. Push and hold the up
ordownbutton
to increase/decrease the setting rapidly. Save the
setting by briefly pushing the button when you
approach the required setting.
• Briefly push and release the MENUbutton to go back
to the menu screen, or push and hold the MENU
button (approximately one second) to go back to the
main screen without storing the settings.
First Page (Display Of Information On The Main
Screen)
This function allows you to choose the information you
would like to see on the main screen. You can view the
date or the trip distance.
4
UNDERSTANDING YOUR INSTRUMENT PANEL 161

To make your choice, proceed as follows:
•Briefly push the MENUbutton.Initial page will be
displayed.
• Briefly push the MENUbutton again to display the
date andengine info options.
• Push the up
ordownbuttons to select the
information you wish to see on the main page of
the display.
• Briefly push the MENUbutton to go back to the
menu screen or hold the button down to go back to
the standard screen without saving.
When the key is turned to MAR/ON and the initial
check stage is over, the display will show the informa-
tion selected via the First Pagemenu function.
Audio Repetition (Repeat Audio Information)
With this function active, the instrument cluster display
shows information relevant to the sound system.
•Radio: tuned radio station frequency, automatic tun-
ing activation or AutoStore.
• CD audio, CD MP3: track number. To activate (On) or to deactivate (Off) the sound system
info displaying, proceed as follows:
1. Briefly push and release the
MENUbutton. Push and
release the up
ordownarrow button to
highlight See Radio and push and release the
MENU button.
2. Push and release the upordownarrow
button for setting.
3. Briefly push and release the MENUbutton to go
back to the menu screen, or push and hold the
MENU button (approximately one second) to go
back to the main screen without storing the settings.
If the radio has Uconnect, refer to the appropriate
“Uconnect Radio Supplement” for further information.
Audio Repetition Submenu Settings:
• Off
• On
• Return to MENU
162 UNDERSTANDING YOUR INSTRUMENT PANEL

Autoclose
With this function active, the doors will automatically
lock at when the vehicle’s speed exceeds 15 mph
(24 km/h).
To change the setting proceed as follows:
1. Briefly push and release theMENUbutton. Push the
up
or downbutton to highlight Autoclose.
Push and release the MENUbutton to enter
Autoclose MENU.
2. Push and release the upordownbutton for
setting.
3. Briefly push and release the MENUbutton to go
back to the menu screen, or push and hold the
MENU button (approximately one second) to go
back to the main screen without storing the settings.
Units (Set Units)
This function may be used to set the measurement unit
in three submenus: “Distance,” “Temperature” and
“Fuel Economy, and Tire Pressure.” To set the required unit, proceed as follows:
1. Briefly push and release the
MENUbutton. Push and
release the up
ordownbutton to highlight
Units. Push and release the MENUbutton to enter
Units MENU.
2. Push and release the upordownbutton to
navigate the three sub-menus.
3. Select the required sub-menu and then briefly push and release the MENUbutton.
4. When accessing the “Distance” submenu, briefly push and release the MENUbutton. Either “mi” or
“km” will appear on the display (according to the
previous setting).
5. Push and release the up
ordownbutton for
setting.
6. Briefly push and release the MENUbutton to return
to the sub-menu.
7. When accessing the “Fuel Economy” submenu, briefly push and release the MENUbutton. Either
“mpg,” “km/l ” or “l/100km” will appear on the
display (according to the previous setting).
4
UNDERSTANDING YOUR INSTRUMENT PANEL 163