wipers FIAT 500L 2019 Owner handbook (in English)

WINDSCREEN
WIPER/REAR
WINDOW WIPER
WINDSCREEN WIPER /
WASHER
6) 7)
This operates only with the ignition key
turned to MAR.
Ring A fig. 31 has five different
positions:
windscreen wiper off
constant flick with 10 second
periods
“faster” flick (speed related)
LOcontinuous slow operation
HIcontinuous fast operation
MIST functionMove the stalk upwards (unstable
position) to activate the MIST
function: operation is limited to the
time for which the stalk is held in this
position. When released, the stalk
will return to its default position and the
windscreen wiper will be stopped.
This function is useful to remove small
deposits of dust from the windscreen,
or morning dew.
“Smart washing” function
Pull the stalk towards the steering
wheel (unstable position) to operate the
windscreen washer. When the stalk is
held pulled for longer than half a
second, the windscreen wiper is moved
with active control.
The wipers flick three times when the
stalk is released, after which, if the
control is in position
, the washing
cycle is concluded by one last flick after
a pause of approximately 6 seconds.
With the ring inLOorHIposition,
the smart washing function is not
carried out.
Raising the blades ("Service
position" function)
This function makes it possible to
replace the blades or protect them in
conditions of ice and/or snow.Function activation
turn the ring A to position(wiper
stopped);
turn the ignition key to the STOP
position;
after having turned the ignition key
to the STOP position, within two
minutes move the lever to the MIST
within two minutes for at least half a
second to activate the wiper for part
of a flick. This operation can be
repeated up to three times, in order to
move the blade to the most suitable
position for replacement;
turn the ignition key to the MAR
position to move the blades back
down.
The function will be deactivated when
the engine is started again, in case of a
wiping request or with the car moving
(speed above 5 km/h).
IMPORTANT Place the blades back in
contact with the windscreen before
activating the windscreen wiper again
and/or turning the ignition key to
MAR-ON.
IMPORTANT Before activating the
function, make sure, when starting the
engine, that the windscreen is free of
snow or ice.
31F0Y0608C
28
KNOWING YOUR CAR

BONNET
OPENING
Pull the lever A fig. 41 in the direction
indicated by the arrow and then
operate the lever B fig. 42 operating in
the direction shown by the arrow.
Then lift the bonnet.
The following plate is present in the
engine compartment fig. 43.IMPORTANT Two side gas shock
absorbers are provided to assist in
opening the bonnet. Do not tamper
with these shock absorbers and
accompany the bonnet when raising.
IMPORTANT Before raising the bonnet,
make sure that the arms of the wipers
are not raised from the windscreen and
that the wiper is not operational.
CLOSING
26)
Lower the bonnet to approximately 20
centimetres from the engine
compartment then let it drop. Make
sure that the bonnet is completely
closed and not only fastened by the
locking device by trying to open it.
If it is not perfectly closed, do not try to
press the bonnet down but open it
and repeat the procedure.
WARNING
26)For safety reasons, the bonnet must
always be properly closed while the car is
travelling. Therefore, make sure that the
bonnet is properly closed and that the lock
is engaged. If you discover that the bonnet
is not perfectly closed during travel, stop
immediately and close the bonnet
correctly.
41F0Y0611C
42F0Y0115C
43F0Y1100C
36
KNOWING YOUR CAR

SERVICING AND CARE
Correct servicing permits the
performance of the vehicle to be
maintained over time, as well as limiting
running costs and safeguarding the
efficiency of the safety systems.
This chapter explains how.SCHEDULED SERVICING ...............149
ENGINE COMPARTMENT ...............159
BATTERY RECHARGING ................164
WINDSCREEN / REAR WINDOW
WIPERS ..........................................165
LIFTING THE CAR...........................167
WHEELS AND TYRES.....................168
BODYWORK ...................................168
148
SERVICING AND CARE

when it is recharged, turn the
charger off before disconnecting it from
the battery;
reconnect the terminal to the
negative battery pole.
VERSIONS WITH
Start&Stop SYSTEM
(for versions/markets, where provided)
To recharge, proceed as follows:
disconnect connector A fig. 163
(pressing button B) from battery status
monitoring sensor C (fitted on the
negative battery terminal D);
connect the positive cable (+) of the
battery charger to the battery positive
terminal (+);
connect the negative cable (–) of the
battery charger to the pin D of the
negative battery terminal (–);
turn on the battery charger. When it
is recharged, turn the charger off before
disconnecting it from the battery;
reconnect the connector A to the
sensor C of the battery.
WARNING
158)Battery fluid is poisonous and
corrosive: avoid contact with your skin and
eyes. The battery should be charged in a
well ventilated place, away from naked
flames or possible sources of sparks:
danger of explosion and fire.159)Do not try to recharge a frozen
battery; defrost it first to prevent the risk of
explosion. If the battery was frozen, have
it inspected by specialised technicians
before recharging to check that the internal
elements are not damaged and that the
casing is not cracked, which could cause
poisonous, corrosive acid to leak.
WINDSCREEN /
REAR WINDOW
WIPERS
160)64)
REPLACING THE
WINDSCREEN WIPER
BLADES
Proceed as follows:
raise the wiper arm, press tab A fig.
164 of the attachment spring and
remove the blade from the arm;
fit the new blade, inserting the tab
into the special slot in the arm, making
sure that it is locked;
lower the wiper arm onto the
windscreen.
163F0Y0153C
164F0Y0114C
165

We really know your car because we invented, designed and built it: we really know every single detail.
At Fiat Service authorised workshopsyou can find technicians directly trained by us,
offering quality and professionalism for all service operations.
Fiat workshops are always close to you for the regular servicing operations, season checks
and practical recommendations by our experts.
With Original Parts distributed by MOPAR
®, you maintain the reliability, comfort
and performance features that you bought your new car for over time.
Always ask for Genuine Parts for the components used on our cars; we recommend them because
they come from our steady commitment in research and development of highly innovative technologies.
For all these reasons: rely on Genuine Parts, because they are the only ones designed
by FCA for your car.
SAFETY:
BRAKING SYSTEMENVIRONMENT: PARTICULATE FILTERS,
CLIMATE CONTROL MAINTENANCECOMFORT: SUSPENSION
AND WINDSCREEN WIPERS PERFORMANCE: SPARK PLUGS,
INJECTORS AND BATTERIESLINEACCESSORI
ROOF RACK BARS, WHEEL RIMS
WHY CHOOSING
GENUINE PARTS