display FIAT 500X 2014 2.G Service Manual

Sport Mode –This mode is designed to increase
steering feedback to the driver with a slight increase in
effort and changes the transmission shift schedules for
more aggressive shifting. This driving mode is useful
while driving on twisty roads where more steering
precision is desired in spirited cornering.
Warning Messages
In the event of a system fault, the system automatically
defaults to Automode and a message will appear in
the instrument cluster display.
Refer to “Instrument Cluster Display” in “Getting To
Know Your Instrument Panel” for further information.
BRAKE CONTROL — IF EQUIPPED
Brake Control
The Brake Control system with mitigation provides the
driver with audible warnings, visual warnings (within
the instrument cluster display), and may apply a brake
jerk to warn the driver when it detects a potential
frontal collision. The warnings and limited braking are
intended to provide the driver with enough time to
react, avoid or mitigate the potential collision. NOTE:
•
Brake Control monitors the information from the
forward looking sensors as well as the Electronic
Brake Controller (EBC), to calculate the probability of
a forward collision. When the system determines that
a forward collision is probable, the driver will be
provided with audible and visual warnings and may
provide a brake jerk warning.
• If the driver does not take action based upon these
progressive warnings, then the system will provide a
limited level of active braking to help slow the
vehicle and mitigate the potential forward collision.
If the driver reacts to the warnings by braking and
the system determines that the driver intends to
avoid the collision by braking but has not applied
sufficient brake force, the system will compensate
and provide additional brake force as required.
Vehicles With A Manual Transmission: After the end
of the intervention of automatic braking, the engine
could stall, unless the driver can depress the clutch
pedal.
Vehicles With Automatic Transmission: After the end
of the intervention of automatic braking, the transmis-
sion may remain in last gear stored: therefore the car
7
STARTING AND OPERATING 239

a more limited and gradual. This setting gives the
driver the maximum possible time of reaction to pre-
vent a possible accident.
By changing the option toNear, the system will warn
the driver of a possible accident with the vehicle ahead
of it when the latter is a reduced distance. This setting
offers a reaction time to the driver lower than the
settings Medium andFar, in the case of a potential
accident, while a more dynamic driving of the car.
The setting of the sensitivity of the system is maintained
in memory when the engine is switched off.
Brake Control Limited Warning
If the instrument cluster display will read “Brake Con-
trol Limited Functionality” or “Brake Control Limited
Functionality Clean Front Windshield” momentarily,
there may be a condition that limits Brake Control
functionality. Although the vehicle is still drivable un-
der normal conditions, the active braking may not be
fully available. Once the condition that limited the
system performance is no longer present, the system
will return to its full performance state. If the problem
persists, see your authorized dealer.
Service Brake Control Warning
If the system turns off, and the instrument cluster
display displays:
• Brake Control Unavailable Service Required
This indicates there is an internal system fault. Al-
though the vehicle is still drivable under normal con-
ditions, have the system checked by an authorized
dealer.
“Wipe Front Radar Sensor In Front Of Vehicle” Warn-
ing
The “Brake Control Front Radar Sensor Temporarily
Blocked” warning will display when conditions tempo-
rarily limit system performance. This most often occurs
at times of poor visibility, such as in snow or heavy rain.
The system may also become temporarily blinded due
to obstructions, such as mud, dirt or ice. In these cases,
the instrument cluster display will display “Brake Con-
trol Front Radar Sensor Temporarily Blocked” and the
system will deactivate.
The “Brake Control Front Radar Sensor Temporarily
Blocked” message can sometimes be displayed while
driving in highly reflective areas (i.e. tunnels with
reflective tiles, or ice and snow). The system will
242 STARTING AND OPERATING

Detection Distances
If the sensors detect more obstacles, it is taken into
account only what is the shorter distance.
Instrument Cluster Display
ParkSense is displayed on the instrument cluster only if
you have selected the itemSound And Displayinside
the Settings menu of the Uconnect system.
If an obstacle is detected in the center rear region, the
display will show a single solid arc in the center rear
region and will produce a one-half second tone. As the
vehicle moves closer to the obstacle, the display will
show the single arc moving closer to the vehicle and the
sound tone will change from slow, to fast, to continu-
ous.
If an obstacle is detected in the left and/or right rear
region, the display will show a single flashing arc in the
left and/or right rear region and will produce a fast
sound tone. As the vehicle moves closer to the obstacle,
the display will show the single arc moving closer to the
vehicle and the tone will change from fast to continu-
ous. In general, the car is closest to the obstacle when the
display shows only a flashing arc and the chime be-
comes continuous.
The color on the display depends on the distance and
location of the obstacle.
Enabling And Disabling ParkSense
ParkSense can be enabled and disabled with the
ParkSense switch.
When the ParkSense switch is pushed to
disable the system, the instrument cluster will
display the “PARKSENSE OFF” message for
approximately five seconds. Refer to “Instru-
ment Cluster Display” in “Getting To Know Your
Instrument Panel” for further information. When the
gear selector is moved to REVERSE and the system is
disabled, the instrument cluster display will show the
“PARKSENSE OFF” message for as long as the vehicle
is in REVERSE.
The ParkSense switch LED will be on when ParkSense
is disabled or requires service. The ParkSense switch
LED will be off when the system is enabled. If the
248 STARTING AND OPERATING

ParkSense switch is pushed, and requires service, the
ParkSense switch LED will blink momentarily, and then
the LED will be on.
ParkSense will remember the previous state when the
vehicle is switch off.
CAUTION!
After turning the ignition to STOP, the ParkSense
remains in this setting until the next key cycle. This
is true even in the case of changing the ignition
from RUN to STOP, and then again to RUN.
Service The Rear Park Assist System
During vehicle start up, when the ParkSense Rear Park
Assist System has detected a faulted condition, the
instrument cluster will actuate a single chime, once per
ignition cycle, and it will display a dedicated message
such as “PARK ASSIST UNAVAILABLE WIPE REAR
SENSORS” or the “PARK ASSIST UNAVAILABLE SER-
VICE REQUIRED” message. Refer to “Instrument Clus-
ter Display” in “Getting To Know Your Instrument
Panel” for further information. When the gear selector
is moved to REVERSE and the system has detected a
faulted condition, the instrument cluster display willdisplay a dedicated message such as
PARK ASSIST
UNAVAILABLE WIPE REAR SENSORS or
PARKSENSE UNAVAILABLE SERVICE REQUIRED 
message for as long as the vehicle is in REVERSE.
Under this condition, Rear Park Assist will not operate.
If a message such as “PARK ASSIST UNAVAILABLE
WIPE REAR SENSORS” appears in the instrument
cluster display, make sure the outer surface and the
underside of the rear fascia/bumper is clean and clear
of snow, ice, mud, dirt or other obstructions, and then
cycle the ignition. If the message continues to appear,
see an authorized dealer.
If a message such as “PARK ASSIST UNAVAILABLE
SERVICE REQUIRED” appears in the instrument clus-
ter display, see an authorized dealer.
ParkSense System Usage Precautions
NOTE:
• Ensure that the outer surface and the underside of
the rear bumper is clean and clear of snow, ice, mud,
dirt or other obstruction to keep the Rear ParkSense
system operating properly.
• Jackhammers, large trucks, and other vibrations
could affect the performance of Rear ParkSense.
7
STARTING AND OPERATING 249

•Clean the Rear ParkSense sensors regularly, taking
care not to scratch or damage them. The sensors must
not be covered with ice, snow, slush, mud, dirt or
debris. Failure to do so can result in the system not
working properly. The Rear ParkSense system might
not detect an obstacle behind the fascia/bumper, or it
could provide a false indication that an obstacle is
behind the fascia/bumper.
• Objects such as bicycle carriers, etc., must not be
placed within 12 inches (30 cm) from the rear fascia/
bumper while driving the vehicle. Failure to do so
can result in the system misinterpreting a close object
as a sensor problem, causing a failure indication to be
displayed in the instrument cluster.
WARNING!
• Drivers must be careful when backing up even
when using ParkSense. Always check carefully
behind your vehicle, look behind you, and be
sure to check for pedestrians, animals, other ve-
hicles, obstructions, and blind spots before back-
ing up. You are responsible for safety and must
continue to pay attention to your surroundings.
(Continued)
WARNING! (Continued)
Failure to do so can result in serious injury or
death.
• Before using ParkSense, it is strongly recom-
mended that the ball mount and hitch ball assem-
bly is disconnected from the vehicle when the
vehicle is not used for towing. Failure to do so can
result in injury or damage to vehicles or obstacles
because the hitch ball will be much closer to the
obstacle than the rear fascia when the loud-
speaker sounds the continuous tone. Also, the
sensors could detect the ball mount and hitch ball
assembly, depending on its size and shape, giving
a false indication that an obstacle is behind the
vehicle.
CAUTION!
• ParkSense is only a parking aid and it is unable to
recognize every obstacle, including small ob-
stacles. Parking curbs might be temporarily de-
tected or not detected at all. Obstacles located
(Continued)
250 STARTING AND OPERATING

CAUTION!(Continued)
above or below the sensors will not be detected
when they are in close proximity.
• The vehicle must be driven slowly when using
ParkSense in order to be able to stop in time
when an obstacle is detected. It is recommended
that the driver looks over his/her shoulder when
using ParkSense.
If it’s necessary to keep the trailer hitch and hitch ball
assembly mounted for a long period, it is possible to
filter out the trailer hitch and hitch ball assembly
presence in sensor field of view. The filtering operation
must be performed only by an authorized dealer.
LANESENSE — IF EQUIPPED
LaneSense Operation
The LaneSense system is operational at speeds above
37 mph (60 km/h) and below 112 mph (180 km/h). The
LaneSense system uses a forward looking camera to
detect lane markings and measure vehicle position
within the lane boundaries. When both lane markings are detected and the driver
unintentionally drifts out of the lane (no turn signal
applied), the LaneSense system provides a haptic warn-
ing in the form of torque applied to the steering wheel
to prompt the driver to remain within the lane bound-
aries. If the driver continues to unintentionally drift out
of the lane, the LaneSense system provides a visual
warning through the instrument cluster display to
prompt the driver to remain within the lane boundaries.
The driver may manually override the haptic warning
by applying torque into the steering wheel at any time.
When only a single lane marking is detected and the
driver unintentionally drifts across the lane marking
(no turn signal applied), the LaneSense system provides
a visual warning through the instrument cluster display
to prompt the driver to remain within the lane. When
only a single lane marking is detected, a haptic (torque)
warning will not be provided.
NOTE:
When operating conditions have been met, the
LaneSense system will monitor if the driver ’s hands are
on the steering wheel and provides an audible warning
to the driver when the driver ’s hands are not detected
on the steering wheel. The system will cancel if the
driver does not return their hands to the wheel.
7
STARTING AND OPERATING 251

Turning LaneSense On Or Off
The default status of LaneSense is “off”.
The LaneSense button is located on the end of the turn
signal stalk, located on the left side of the steering
column.To turn the LaneSense system on, push the
LaneSense button once. A “Lane Sense On”
message is shown in the instrument cluster display.
To turn the LaneSense system off, push the LaneSense
button once.
NOTE: The LaneSense system will retain the last sys-
tem state on or off from the last ignition cycle when the
ignition is changed to RUN mode.
LaneSense Warning Message
The LaneSense system will indicate the current lane
drift condition through the instrument cluster display.
Base Instrument Cluster Display
When the LaneSense system is on, the lane lines are
gray when both of the lane boundaries have not been
detected and the LaneSense indicator is solid white. Left Lane Departure — Only Left Lane Detected
•
When the LaneSense system is on, the LaneSense
indicator is solid white when only the left lane
marking has been detected and the system is ready to
provide visual warnings in the instrument cluster
display if an unintentional lane departure occurs.
• When the LaneSense system senses the lane has been
approached and is in a lane departure situation, the
left thick lane line flashes yellow (on/off), the left
thin line remains solid yellow and the LaneSense
indicator changes from solid white to flashing yel-
low.
System On (Gray Lines/White Indicator)
252 STARTING AND OPERATING

NOTE:The LaneSense system operates with the similar
behavior for a right lane departure when only the right
lane marking has been detected.
Left Lane Departure — Both Lanes Detected
• When the LaneSense system is on, the lane lines turn
from gray to white to indicate that both of the lane
markings have been detected. The LaneSense indica-
tor is solid green when both lane markings have been
detected and the system is “armed” to provide visual warnings in the instrument cluster display and a
torque warning in the steering wheel if an uninten-
tional lane departure occurs.
• When the LaneSense system senses a lane drift
situation, the left thick lane line and left thin line turn
solid yellow. The LaneSense indicator changes from
solid green to solid yellow. At this time torque is
applied to the steering wheel in the opposite direc-
tion of the lane boundary.
• For example: If approaching the left side of the lane
the steering wheel will turn to the right.
Lane Approached (Flashing Yellow Thick Line, Solid
Yellow Thin Line/Flashing Yellow Indicator)
Lanes Sensed (White Lines/Green Indicator)
7
STARTING AND OPERATING 253

NOTE:
•When enabled the system operates above 37 mph
(60 km/h) and below 112 mph (180 km/h).
• Use of the turn signal suppresses the warnings.
• The system will not apply torque to the steering
wheel whenever a safety system engages. (anti-lock
brakes, traction control system, electronic stability
control, forward collision warning, etc.).
PARKVIEW REAR BACK UP CAMERA — IF
EQUIPPED
The ParkView Rear Back Up Camera that allows you to
see an on-screen image of your vehicle’s rear surround-
ings when the gear selector is put into REVERSE. The
image will be displayed on the touchscreen display
along with a note to “check entire surroundings” across
the top of the screen. After five seconds this note will
disappear. The ParkView camera is located above the
rear license plate. When the vehicle is shifted out of REVERSE (with
camera delay turned off), the rear camera mode is
exited and the navigation or audio screen appears
again.
When the vehicle is shifted out of REVERSE (with
camera delay turned on), the camera image will con-
tinue to be displayed for up to 10 seconds after shifting
out of REVERSE unless the vehicle speed exceeds
8 mph (13 km/h), the vehicle is shifted into PARK or the
ignition is switched to STOP mode.Parking Camera7
STARTING AND OPERATING 255

A touchscreen button to disable the camera is available
when the vehicle is not in REVERSE. Display of the
camera image after shifting out of REVERSE can be
disabled via Uconnect Settings.
When enabled, active guide lines are overlaid on the
image to illustrate the width of the vehicle and its
projected backup path based on the steering wheel
position.When enabled, fixed guide lines are overlaid on the
image to illustrate the width of the vehicle.
Different colored zones indicate the distance to the rear
of the vehicle.
The following table shows the approximate distances
for each zone:
Zone
Distance To The Rear Of The Vehicle
Red 0 - 1 ft (0 - 30 cm)
Yellow 1 ft - 3 ft (30 cm - 1 m)
Green 3 ft or greater (1 m or greater)
NOTE: If snow, ice, mud, or any foreign substance
builds up on the camera lens, clean the lens, rinse with
water, and dry with a soft cloth. Do not cover the lens.
WARNING!
Drivers must be careful when backing up even
when using the ParkView Rear Back Up Camera.
Always check carefully behind your vehicle, and be
(Continued)
WARNING! (Continued)
sure to check for pedestrians, animals, other ve-
hicles, obstructions, or blind spots before backing
up. You are responsible for the safety of your
surroundings and must continue to pay attention
while backing up. Failure to do so can result in
serious injury or death.
256 STARTING AND OPERATING