inflation pressure FIAT BRAVO 2007 2.G Owners Manual
[x] Cancel search | Manufacturer: FIAT, Model Year: 2007, Model line: BRAVO, Model: FIAT BRAVO 2007 2.GPages: 246, PDF Size: 3.75 MB
Page 98 of 246
97
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
Replacing standard tyres
with winter tyres and vice
versa involves T.P.M.S. system set-up
that shall be performed at Fiat Deal-
erships only.
The T.P.M.S. system re-
quires special equipment.
Consult Fiat Dealership to know
what type of accessories are com-
patible with the system (wheels,
wheel caps, etc.). Using other acces-
sories could cause system malfunc-
tioning.Tyre pressure could change
according to outside tem-
perature. For this reason the T.P.M.S.
system could temporarily indicate low
tyre pressure. In this event check pres-
sure with cold tyres and restore prop-
er inflation values if required.
If the car is fitted with
T.P.M.S. system, when
changing a tyre, change also the rub-
ber seal of the valve. Contact a Fiat
Dealership.If the car is fitted with
T.P.M.S. system, tyre and/or
rim removal and refitting operations
involve special precautions; to pre-
vent damages or wrong sensor refit-
ting, contact Fiat Dealership to have
tyre and/or rim changed.
Strong radio-frequency nois-
es could inhibit the regular
operation of the T.P.M.S. system.
This condition will be indicated by the
turning on of warning light nor sym-
bol on the instrument panel, togeth-
er with the message on the display.
Such indication will disappear auto-
matically as soon as radio-frequency
noises will stop to disturb the system.
WARNINGWARNING
WARNING
WARNING
WARNING
WARNING
083-104 BRAVO GB 10-05-2007 9:10 Pagina 97
Page 140 of 246
139
DASHBOARD
AND CONTROLS
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
SAFETY
DEVICES
CORRECT USE
OF THE CAR
SNOW TYRES
Use snow tyres of the same size as the
normal tyres provided with the car.
Fiat Dealership will be happy to provide
advice concerning the most suitable type
of tyre for the customer’s requirements.
For the type of tyre to be used, inflation
pressures and the specifications of snow
tyres, follow the instructions given in para-
graph “Wheels” in section “Technical
specifications”.
The winter features of these tyres are re-
duced considerably when the tread depth
is below 4 mm. In this case, they should
be replaced.Due to the snow tyre features, under nor-
mal conditions of use or on long motor-
way journeys, the performance of these
tyres is lower than that of normal tyres. It
is therefore necessary to limit their use to
the purposes for which they are certified.
IMPORTANT When snow tyres are used
with a max speed index below the one
that can be reached by the car (increased
by 5%), place a notice in the passenger’s
compartment, plainly in the driver’s view
which states the max permissible speed of
the snow tyres (as per EC Directive).
All four tyres should be the same (brand
and track) to ensure greater safety when
driving and braking and better driveability.
Remember that it is inappropriate to
change the direction of rotation of tyres.
The max speed for snow
tyres with “Q” marking is
160 km/h; 190 km/h for tyres with “T”
marking and 210 km/h for tyres with
H marking. The Road Traffic Code
speed limits must however be always
strictly observed.
WARNING
SNOW CHAINS
Use of snow chains should be in compli-
ance with local regulations.
Snow chains should only be applied to the
driving wheels (front wheels).
Check the tension of the chains after the
first few metres have been driven. Use
snow chains with reduced size: for 195/65
R15” and 205/55 R16” tyres use snow
chains with reduced size with max pro-
trusion beyond the tyre profile of 9 mm.
IMPORTANT Snow chains cannot be fit-
ted to the space-saver spare wheel. So, if
a front wheel is punctured and chains are
needed, a rear wheel should be fitted to
the front of the car and the spare wheel
should be fitted to the rear.
129-140 BRAVO GB 10-05-2007 9:16 Pagina 139
Page 153 of 246
152
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
WARNING
LIGHTS AND
MESSAGES
Check tyre pressure
The warning light (or the symbol on the
display) turns on to indicate the flat tyre.
Should two or more tyre be flat, the dis-
play will show the indications corre-
sponding to each tyre in sequence.
Restore proper inflation pressure values
as soon as possible (see paragraph “Cold
inflation pressures” in section “Technical
Specifications”).Tyre pressure unsuitable for speed
Should it be required to journey at a speed
higher than 160 km/h, inflate tyres at pres-
sures values specified in paragraph “Infla-
tion pressures”.
If the T.P.M.S. system (where provided)
detects that the pressure of one or more
tyres is unsuitable for the current speed,
the warning light will turn on (together
with the message on the display) (see para-
graph “Low tyre pressure” in this section)
and it will stay on until the car speed slow
downs below the preset threshold.
IMPORTANT In this case slow down im-
mediately since tyre overheating could im-
pair tyre performance and life beyond re-
pair, and even make the tyre to blow-out.
Strong radio-frequency nois-
es could inhibit the regular
operation of the T.P.M.S. system.
This condition will be indicated by a
message (where provided). The warn-
ing message will go off automatical-
ly as soon as the radio-frequency
noise will stop to disturb the system.
WARNING
141-154 BRAVO GB 10-05-2007 9:17 Pagina 152
Page 159 of 246
158
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
The jack shall only be used
for changing wheels on the
car with which it is provided or on
cars of the same model. It must not
be used for other purposes such as for
instance raising cars of other models.
In no case should it be used for repairs
under the car. Incorrect positioning
of the jack may cause the jacked car
to fall. Do not use the jack for high-
er capacities than stated on its label.
Snow chains cannot be fitted to the
space-saver spare wheel. So, if a front
(drive) wheel is punctured and chains
are needed, a rear wheel should be
fitted to the front of the car and the
spare wheel should be fitted to the
rear. This way with two normal dri-
ve wheels, snow chains can be fitted
to them to solve an emergency.
WARNING
Fasten the wheel cap cor-
rectly to prevent the wheel
from coming free in motion. Never
tamper with the inflation valve. Nev-
er place tools between the rim and
tyre. Check and restore, if required,
the pressure of tyres and spare wheel
to the values given in section “Tech-
nical specifications”.
WARNING
When driving with a space-
saver spare wheel fitted, the
driving performance of the car
changes. Avoid accelerating or brak-
ing sharply, abrupt turns or fast cor-
nerings. The life of the spare wheel
is approx. 3000 Km, after this dis-
tance it should be replaced with an-
other of the same type. Never at-
tempt to fit a conventional tyre on a
rim designed for use as a space-saver
spare wheel. Have the punctured
wheel repaired and refitted as soon
as possible. Two or more space-saver
spare wheels should never be used to-
gether. Do not grease the threads of
bolts before installing them: they
might slip out.
WARNING
155-190 BRAVO GB 10-05-2007 9:19 Pagina 158
Page 166 of 246
165
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
❒make sure the compressor switch
E-fig. 15is set to 0(off), start the en-
gine and fit plug D-fig. 14into the cig-
ar lighter outlet and then turn on the
compressor by setting switch E-fig. 15
to I(on). Inflate the tyre to the pres-
sure specified in paragraph “Cold tyre
inflation pressure” in section “Techni-
cal specifications”. Check tyre pressure
on gauge F-fig. 15with compressor off
to obtain precise reading; ❒If after 5 minutes it is still impossible
to reach at least 1.5 bar, disengage com-
pressor from valve and current outlet,
then move the car forth for approx. ten
metres in order to distribute the seal-
ing fluid inside the tyre evenly, then re-
peat the inflation operation;
❒If after this operation it is still impossi-
ble after 5 minutes to reach at least 1.8
bar, do not start driving since the tyre
is excessively damaged and the quick
tyre repair kit cannot guarantee suit-
able sealing, contact Fiat Dealership;
❒If reaching the tyre pressure specified
in paragraph “Cold tyre inflation pres-
sure” in section “Technical specifica-
tions”, start driving immediately;
Apply the sticker in a visible
position for the driver to in-
dicate that the tyre has been treat-
ed with the quick tyre repair kit. Dri-
ve carefully especially when corner-
ing. Do not exceed 80 km/h. Avoid
heavy braking and accelerating.
WARNING
❒after driving for about 10 minutes stop
and check again the tyre pressure; pull
up the handbrake;
fig. 14F0Q0515mfig. 15F0Q0516mfig. 15aF0Q0017m
155-190 BRAVO GB 10-05-2007 9:19 Pagina 165
Page 205 of 246
204
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
CAR
MAINTENANCE
WHEELS AND TYRES
Check the pressure of each tyre, includ-
ing the spare, every two weeks and before
long journeys. The pressure should be
checked with the tyre rested and cold.
For the correct tyre inflation pressure, see
“Wheels” in “Technical specifications”
section.
Incorrect pressure causes abnormal tyre
wearfig. 13:
A: normal pressure: tread evenly worn.
B: low pressure: tread particularly worn
at the edges.
C: high pressure: tread particularly worn
in the centre.
Tyres must be replaced when the tread
wears down to 1.6 mm. In any case, com-
ply with the laws in the country where the
car is being driven.IMPORTANT NOTES
❒ As far as possible, avoid sharp braking
and screech starts, etc. Be careful not
to hit the kerb, potholes or other ob-
stacles hard. Driving for long stretch-
es over bumpy roads can damage the
tyres;
❒ Periodically check that the tyres have
no cuts in the side wall, abnormal
swelling or irregular tyre wear. If any of
these occur, have the car seen to at a
Fiat Dealership;
❒avoid overloading the car when travel-
ling: this may cause serious damage to
the wheels and tyres;
fig. 13F0Q0101m
❒if a tyre is punctured, stop immediate-
ly and charge it to avoid damage to the
tyre, the rim, suspensions and steering
system;
❒ Tyres age even if they are not used
much. Cracks in the tread rubber are a
sign of ageing. In any case, if the tyres
have been on the car for over 6 years,
they should be checked by specialised
personnel, to see if they can still be
used. Also remember to check the
space-saver spare wheel;
❒ In the case of replacement, always fit
new tyres, avoiding those of dubious
origin;
❒ If a tyre is changed, also change the in-
flation valve;
❒To allow even wear between the front
and rear tyres, it is advisable to change
them over every 10-15 thousand kilo-
metres, keeping them on the same side
of the car so as to not reverse the di-
rection of rotation.
191-212 BRAVO GB 10-05-2007 9:21 Pagina 204
Page 224 of 246
223
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
INDEX
TECHNICAL
SPECIFICATIONS
COLD TYRE INFLATION PRESSURE (bar)
Add +0.3 bar to the prescribed inflation pressure when the tyres are warm. Recheck pressure value with cold tyres.
With snow tyres, add +0.2 bar to the inflation pressure value prescribed for standard tyres.
When running at speed higher than 160 km/h, inflate tyres at full load inflation values.
T.P.M.S. system not available for tyre 195/65 R15 91H
195/65 R15 91H 2.3 2.3 2.6 2.6
1.4 16V205/55 R16 91H 2.3 2.3 2.6 2.6
225/45 R17 91V 2.3 2.3 2.6 2.6
195/65 R15 91H 2.3 2.3 2.6 2.6
1.9 Multijet 8V205/55 R16 91H 2.3 2.3 2.6 2.6
225/45 R17 91V 2.3 2.3 2.6 2.6
225/40 R18 92V 2.6 2.6 2.9 2.9
195/65 R15 91V 2.3 2.3 2.6 2.6
1.9 Multijet 16V205/55 R16 91V 2.3 2.3 2.6 2.6
1.4 T-JET 150 HP225/45 R17 91V 2.3 2.3 2.6 2.6
225/40 R18 92V 2.6 2.6 2.9 2.9STANDARD TYRES
Size Medium load Full load
Front Rear Front Rear
213-236 BRAVO GB 16-05-2007 10:11 Pagina 223
Page 245 of 246
ENGINE OIL CHANGE
1.4 16V- 1.4 T-JET 150 HP
- 1.9 Multijet 8V - 1.9 Multijet 16V
Tank capacity 57
Reserve8-10
Refuel petrol engines with unleaded petrol with octane rating (RON) no lower than 95 only (EN 228 Specifications)
Refuel diesel engines with diesel fuel for motor vehicles only (EN 590 Specifications)
FUEL CAPACITIES (litres)
Fiat Group Automobiles S.p.A. - Quality - Assistenza Tecnica - Ingegneria Assistenziale - Largo Senatore G. Agnelli, 5 - 10040 Volvera - Torino (Italia) - Print N. 603.81.209 - 05/2007 - 1stEdition
1.4 16V- 1.4 T-JET 150 HP 1.9 Multijet8V- 1.9 Multijet 16Vlitres kg litres kg
Fuel tank 2.75 2.4 4.4 3.8
Engine sump and filter 2.9 2.55 4.7 4.0
Add +0.3 bar to the prescribed inflation pressure when the tyres are warm. Recheck pressure value with cold tyres.
With snow tyres, add +0.2 bar to the inflation pressure value prescribed for standard tyres.
When running at speed higher than 160 km/h, inflate tyres at full load inflation values.
T.P.M.S. system not available for tyre 195/65 R15 91H.
COLD TYRE INFLATION PRESSURE (bar)
195/65 R15 91H 2.3 2.3 2.6 2.6
1.4 16V205/55 R16 91H 2.3 2.3 2.6 2.6
225/45 R17 91V 2.3 2.3 2.6 2.6
195/65 R15 91H 2.3 2.3 2.6 2.6
1.9 Multijet 8V205/55 R16 91H 2.3 2.3 2.6 2.6
225/45 R17 91V 2.3 2.3 2.6 2.6
225/40 R18 92V 2.6 2.6 2.9 2.9
1.4 T-JET 150 HP195/65 R15 91V 2.3 2.3 2.6 2.61.9 Multijet 16V
205/55 R16 91V 2.3 2.3 2.6 2.6
225/45 R17 91V 2.3 2.3 2.6 2.6
225/40 R18 92V 2.6 2.6 2.9 2.9STANDARD TYRES
Size Medium load Full load
Front Rear Front Rear
237-244 BRAVO GB 10-05-2007 9:23 Pagina 244