lock FIAT BRAVO 2008 2.G Owner's Guide

ENGINE STARTING
The car is fitted with an electronic engine
lock device: if the engine fails to start, see
the paragraph “The Fiat CODE system” in
section “Dashboard and controls”.
The engine may be noisier than usual dur-
ing the first seconds of operation, espe-
cially after it has not been used for a while.
This characteristic feature of the hydraulic
tappet system does not compromise func-
tionality or reliability. This timing system
for petrol engines was adopted to limit
servicing.
Engine starting is guaranteed up to a min-
imum temperature of –18°C (Italy and
Middle Europe) and –20°C (North Eu-
rope).
130
SAFETY
DEVICES
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATION
INDEX
DASHBOARD
AND CONTROLS
CORRECT USE
OF THE CAR
STARTING PROCEDURE FOR
PETROL VERSIONS
Proceed as follows:
❒pull up the handbrake;
❒set the gear lever to neutral;
❒press the clutch pedal down to the
floor without touching the accelerator;
❒turn the ignition key to AVVand let
it go the moment the engine starts.
If the engine does not start at the first at-
tempt, return the ignition key to STOP
before repeating starting.
If, when the ignition key is at MAR, warn-
ing light
Yremains (or the symbol on dis-
play) lit together with warning light U,
turn the key to STOPand then back to
MAR; if the warning light remains on, try
with the other keys provided with the car.
We recommend that during
the initial period you do not
drive to full car performance
(e.g.: excessive acceleration,
long journeys at top speed, sharp brak-
ing, etc.).
Running the engine in con-
fined areas is extremely dan-
gerous. The engine consumes oxygen
and produces carbon monoxide
which is a highly toxic and lethal gas.
WARNING
When the engine is switched
off never leave the ignition key
at MARto prevent pointless
current absorption from drain-
ing the battery.
If you are still unable to start the engine,
perform the emergency start-up proce-
dure (see “Emergency start-up” in section
“In an emergency”) and contact Fiat Deal-
ership.
IMPORTANT Never leave the ignition key
at MARwhen the engine is off.
129-140 BRAVO GB 29-10-2008 12:35 Pagina 130

133
DASHBOARD
AND CONTROLS
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
SAFETY
DEVICES
CORRECT USE
OF THE CAR
PARKING
Proceed as follows:
❒ Stop the engine and engage the hand-
brake;
❒Engage a gear (first if the car is faced up-
hill or reverse if it is faced downhill) and
leave the wheels steered.
Block the wheels with a wedge or a stone
if the car is parked on a steep slope. Do
not leave the ignition key at MARto pre-
vent draining the battery. Always remove
the key when you leave the car.HANDBRAKE
The handbrake lever is located between
the two front seats.
Pull the handbrake lever upwards until the
car cannot be moved.
Four or five clicks are generally enough
when the car is on level ground while nine
or ten may be required if the car is on a
steep slope or laden.
IMPORTANT If this is not the case, con-
tact Fiat Dealership to have the handbrake
adjusted.
In cars fitted with front armrest, lift the
latter so that it does not hinder the hand-
brake engaging procedure.When the handbrake lever is pulled up
and the ignition key is at MAR, the in-
strument panel warning light
xwill turn
on.
To release the handbrake:
❒slightly lift the handbrake and press re-
lease button A-fig. 1;
❒keep button Apressed and lower the
lever. Warning light xwill turn off.
Press the brake pedal when carrying out
this operation to prevent the car from
moving accidentally.
fig. 1F0Q0628m
Never leave children unat-
tended in the car. Always re-
move the ignition key when leaving
the car and take it out with you.
WARNING
129-140 BRAVO GB 29-10-2008 12:35 Pagina 133

141
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
WARNING
LIGHTS AND
MESSAGES
GENERAL WARNINGS ..................................................... 142
LOW BRAKE FLUID............................................................ 142
HANDBRAKE ON................................................................ 142
BRAKE PAD WEAR ............................................................ 142
AIR BAG FAILURE................................................................ 143
FRONT PASSENGER AIR BAG/
SIDE BAGS DEACTIVATED....................................................... 143
SEAT BELTS NOT FASTENED.......................................... 144
LOW BATTERY CHARGE................................................. 144
LOW ENGINE OIL PRESSURE.......................................... 144
EXHAUSTED OIL ................................................................ 144
“DUALDRIVE” ELECTRIC POWER
STEERING FAILURE.............................................................. 145
“DUALDRIVE” ELECTRIC POWER STEERING
ACTIVATION ....................................................................... 145
ENGINE COOLANT HIGH TEMPERATURE................ 146
INCOMPLETE DOOR LOCKING.................................... 146
BOOT OPEN......................................................................... 146
BONNET OPEN................................................................... 146
GENERIC FAILURE INDICATION ................................. 147
DIESEL PARTICULATE FILTER CLOGGED ................. 147
FUEL RESERVE....................................................................... 147
EOBD/INJECTION SYSTEM FAILURE............................. 148
ESP SYSTEM .......................................................................... 148
HILL HOLDER FAILURE .................................................... 148
GLOW PLUG WARMING ................................................ 149GLOW PLUG WARMING FAILURE............................... 149
WATER IN DIESEL FUEL FILTER..................................... 149
ABS SYSTEM FAILURE......................................................... 149
EBD SYSTEM FAILURE........................................................ 150
CAR PROTECTION SYSTEM
FAILURE FIAT CODE.......................................................... 150
ALARM FAILURE.................................................................. 150
THEFT ATTEMPT................................................................. 150
T.P.M.S. SYSTEM FAILURE ................................................. 151
LOW TYRE PRESSURE ...................................................... 151
CHECK TYRE PRESSURE .................................................. 151
TYRE PRESSURE UNSUITABLE FOR SPEED ................. 151
EXTERNAL LIGHTS FAILURE........................................... 153
BRAKE LIGHTS FAILURE................................................... 153
REAR FOGLIGHTS............................................................... 153
FRONT FOG LIGHTS.......................................................... 153
LEFT-HAND DIRECTION INDICATOR........................ 153
RIGHT-HAND DIRECTION INDICATOR.................... 153
SIDE/TAILLIGHTS AND LOW BEAMS ........................... 154
FOLLOW ME HOME........................................................... 154
MAIN BEAMS......................................................................... 154
CRUISE CONTROL ............................................................ 154
POSSIBLE PRESENCE OF ICE ON THE ROAD ........... 154
LIMITED RANGE ................................................................. 154
ASR SYSTEM ......................................................................... 154
SPEED LIMIT EXCEEDED .................................................. 154
SPORT FUNCTION ACTIVATION................................. 154
WW W
A A
R R
N N
I I
N N
G G
L L
I I
G G
H H
T T
S S
A A
N N
D D
M M
E E
S S
S S
A A
G G
E E
S S
141-154 BRAVO GB 29-10-2008 12:32 Pagina 141

146
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
WARNING
LIGHTS AND
MESSAGES
ENGINE COOLANT
HIGH TEMPERATURE
(red)
Turning the ignition key to MAR
the warning light turns on, but it should go
off after few seconds.
The warning light turns on when the en-
gine is overheated.
If the warning light comes on, proceed as
follows:
❒normal driving conditions: stop the
car, switch off the engine and check
whether the water level in the reser-
voir is not below the MIN mark. Oth-
erwise wait for few seconds to allow
engine cooling, then open slowly and
carefully the cap, top up coolant and
check whether its level is falling be-
tween MIN and MAX marks in the
reservoir. Check visually any leak and if
when restarting the warning light
comes on again, contact a Fiat Dealer-
ship.
❒Car heavy duty(e.g.: towing trailer
uphill of fully laden car): decrease speed,
if the warning light stays on, stop the
car. Wait for 2 or 3 minutes leaving the
engine on and slightly accelerated to
further activate the circulation of the
coolant fluid, then switch the engine off.
Check proper coolant level as de-
scribed previously.
IMPORTANT Under severe use of the
car, keep the engine on and slightly accel-
erated for few minutes before switching it
off.
The display will show the dedicated mes-
sage.
ç
INCOMPLETE DOOR
LOCKING (red)
The warning light (or the sym-
bol on the display) turns on when
one or more doors are not properly shut.
The buzzer will sound when one or more
doors are open and the car is moving.
´
BOOT OPEN
The symbol (where provided)
on the display turns on when
the boot is not properly shut.
On certain versions the warning light
´turns on instead.
R
BONNET OPEN
The symbol (where provided)
on the display turns on when
the bonnet is not properly shut.
On certain versions the warning light
´
turns on instead.
S
141-154 BRAVO GB 29-10-2008 12:32 Pagina 146

150
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
WARNING
LIGHTS AND
MESSAGES
EBD SYSTEM
FAILURE
(red)
(amber)
The turning on at the same time of warn-
ing lights
xand >with the engine run-
ning indicates an EBD system failure or
that the system is unavailable; in this case
heavy braking may cause the rear wheels
to lock before time, with the possibility of
skidding.
Drive with the utmost care to the near-
est Fiat Dealership to have the system
checked.
The display will show the dedicated mes-
sage.
x>
CAR PROTECTION
SYSTEM FAILURE -
FIAT CODE
(amber)
ALARM FAILURE
(where provided)
(amber)
THEFT ATTEMPT
(amber)
Car protection system failure -
Fiat Code
Turning the key to MARthe warning light
shall flash only once and then go off.
The turning on of the warning light (or the
symbol on the display) glowing steadily,
with the ignition key at MAR, indicates a
probable failure (see “Fiat Code system”
in section “Dashboard and controls”).
The display will show the dedicated mes-
sage.
IMPORTANT The turning on at the same
time of warning lights
Uand Y(or sym-
bol on display) indicates a failure of the Fi-
at CODE system.
Y
If with the engine running the warning lightYflashes, this means that the car is not
protected by the engine immobilising de-
vice (see “Fiat Code system” in section
“Dashboard and controls”).
Contact Fiat Dealership to have all the
keys memorised.
Alarm failure (where provided)
The turning on of the warning light (or
symbol on display) indicates a failure in the
alarm system. Contact Fiat Dealership as
soon as possible.
The display will show the dedicated mes-
sage.
Theft attempt
The turning on of the warning light (or
symbol on display) indicates an attempt of
break-in. Contact Fiat Dealership as soon
as possible.
The display will show the dedicated mes-
sage.
141-154 BRAVO GB 29-10-2008 12:32 Pagina 150

166
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
FOR CHECKING AND
RESTORING PRESSURE ONLY
The compressor can be also used just for
restoring pressure. Disconnect the quick
connection and connect it directly to the
tyre valve fig. 16; in this way the cylinder
is not connected to compressor and the
sealing fluid will not flow into the tyre. CYLINDER REPLACEMENT
PROCEDURE
To replace the cylinder proceed as fol-
lows:
❒disconnect connection B-fig. 17;
❒turn counter-clockwise the cylinder to
replace and raise it;
❒fit the new cylinder and turn it clock-
wise;
❒connect connection Bto the cylinder
and fit the transparent tube Ainto the
proper space.
fig. 16F0Q0517mfig. 17F0Q0512m
❒if at least 1.8 bar pressure is read, re-
store proper pressure (with engine
running and handbrake on) and restart;
❒drive with the utmost care to the near-
est Fiat Dealership.
It is of vital importance to
communicate that the tyre
has been repaired using the quick tyre
repair kit. Hand the instruction
brochure to the personnel charged
with treating the tyre repaired with
the kit.
WARNING
If the pressure falls below 1.8
bars, do not drive any fur-
ther: the quick tyre repair kit Fix & Go
automatic cannot guarantee proper
hold because the tyre is too much
damaged. Contact Fiat Dealership.
WARNING
155-190 BRAVO GB 29-10-2008 12:35 Pagina 166

168
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
F0Q0391m
C Tubular bulbs: free them from their
contacts to remove.
D-E Halogen bulbs: to remove the bulb,
release the clip holding the bulb in
place.
F Gas-discharge bulbs (Bi-Xenon).
fig. 18
TYPES OF BULBS fig. 18
Various types of bulbs are fitted to your
car:
A All glass bulbs: these are pressed on.
Pull to remove.
B Bayonet type bulbs: press the bulb,
turn counterclockwise to remove this
type of bulb from its holder.
155-190 BRAVO GB 29-10-2008 12:35 Pagina 168

171
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
SIDELIGHTS
To change the bulb, proceed as follows:
❒remove the protective cover A-fig. 19;
❒turn the bulb holder A-fig. 21coun-
terclockwise and then withdraw it;
❒remove the bulb Band replace it;
❒fit the new bulb, refit the bulb holder
A-fig. 21 and then refit the protective
coverB-fig. 19correctly.MAIN BEAM HEADLIGHTS
To change the bulb, proceed as follows:
❒remove the protective cover A-fig. 19;
❒release the bulb holder catch A-fig. 22;
❒remove the bulb Cand replace it;
❒fit the new bulb, making the tabs of the
metallic part coincide with the grooves
on the reflector, reconnect the electri-
cal connector Bthen hook the bulb
holder catch A;
❒refit the protective cover B-fig. 19cor-
rectly.
fig. 21F0Q0706mfig. 22F0Q0707mfig. 23F0Q0708m
DIRECTION INDICATORS
Front
To change the bulb, proceed as follows:
❒turn the protective cover C-fig. 19
counterclockwise;
❒remove the bulb B-fig. 23and replace
it;
❒refit the protective cover Acorrectly.
155-190 BRAVO GB 29-10-2008 12:35 Pagina 171

172
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
REAR LIGHT UNITS fig. 26
Rear light units contain taillights, direction
indicators and brake light (stop) bulbs.
The bulbs are arranged inside the light unit
fig. 26as follows:
B taillights/brake light (double light);
C direction indicators. Side
To change the bulb, proceed as follows:
❒push the transparent cover A-fig. 24
to compress the internal catch B, then
remove the unit;
❒turn the bulb holder C counterclock-
wise, remove the snap-fitted bulb D
and replace it;
❒refit the bulb holder Cin the lens by
turning it clockwise;
❒refit the unit making sure the catch
clicks into place B.FRONT FOG LIGHTS fig. 25
(where provided)
Contact Fiat Dealership to have front fog
lights replaced.
fig. 24F0Q0709mfig. 25F0Q0710mfig. 26F0Q0714m
155-190 BRAVO GB 29-10-2008 12:35 Pagina 172

174
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
NUMBER PLATE LIGHTS
To change the bulb proceed as follows:
❒work in the point shown by the arrow
and remove lens unit A-fig. 34;
❒turn the bulb holder B-fig. 35clock-
wise;
❒remove the bulb C and replace it. THIRD BRAKE LIGHT
To change the bulb proceed as follows:
❒open the tailgate;
❒remove cover A-fig. 32;
❒remove the lens unit B-fig. 33and dis-
connect the electric connector;
❒press the tabs C-fig. 33and remove
the bulb holder;
❒remove the snap-fitted bulb and replace
it.
❒refit cover A-fig. 32and then close the
tailgate.
fig. 33F0Q0751m
fig. 32F0Q0716m
fig. 34F0Q0718m
fig. 35F0Q0719m
155-190 BRAVO GB 29-10-2008 12:35 Pagina 174