fuel FIAT BRAVO 2009 2.G Owner's Manual
[x] Cancel search | Manufacturer: FIAT, Model Year: 2009, Model line: BRAVO, Model: FIAT BRAVO 2009 2.GPages: 246, PDF Size: 4.1 MB
Page 148 of 246

147
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
WARNING
LIGHTS AND
MESSAGES
GENERIC FAILURE
INDICATION
(amber)
Inertial fuel cut-off switch
intervened
The warning light (or the symbol on dis-
play) comes on when the inertial fuel cut-
off switch is triggered.
The display will show the dedicated mes-
sage.
Engine oil pressure sensor failure
The warning light (or the symbol on the
display) turns on when a fault is detected
to engine oil pressure sensor.
Twilight sensor failure
The warning light (or the symbol on dis-
play) turns on when a fault is detected to
the twilight sensor.
The display will show the dedicated mes-
sage.
Speed limit exceeded
(only for Arabic countries)
The warning light (amber), or symbol on
the display (red), comes on when a speed
of 120 km/h is exceeded.
è
CLEANING DPF
(PARTICULATE
FILTER) IN PROGRESS
(only Multijet versions
with DPF - amber)
When the ignition key is turned to MAR,
the warning light switches on but it must
switch off after a few seconds. The warn-
ing light comes on constantly to notify the
driver that the DPF system needs to elim-
inate captured pollutants (particulate) by
the regeneration process. The warning
light does not come on during every DPF
regeneration, but only when driving con-
ditions require notification of the driver.
To switch the warning light off, the car
must stay in motion until regeneration has
been completed. The process normally
takes about 15 minutes. The optimum con-
ditions to end the process are achieved by
keeping the car in motion up to 60km/h
with an engine speed higher than 2,000
rpm.
This light coming on is not a car defect and
therefore the car does not need to go to
the workshop.
A specific message will appear on the dis-
play when the warning light comes on (for
versions/markets, where provided).
h
Rain sensor failure
The warning light (or the symbol on the
display) on the dial turns on when the rain
sensor is faulty. Contact Fiat Dealership.
The display will show the dedicated mes-
sage.
Parking sensors failure
(for versions/markets, where provided)
The warning light (or the symbol on the
display) when a fault is detected to park-
ing sensors.
Tyre pressure monitoring
system failure
(for versions/markets, where provided)
The warning light (or the symbol on the
display) turns on when a failure is detect-
ed in the T.P.M.S. system (for versions/
markets, where provided).
Should one or more wheels without sen-
sor be fitted, the instrument panel warn-
ing light will come on and stay on until
restoring initial conditions.
The display will show the dedicated mes-
sage.
NOTE When one of the above faults oc-
curs, contact your Fiat Dealership as soon
as possible.
141-154 BRAVO GB:141-154 BRAVO GB 11-11-2009 10:55 Pagina 147
Page 149 of 246

148
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
WARNING
LIGHTS AND
MESSAGES
EOBD/INJECTION
SYSTEM FAILURE
(amber)
Under normal conditions, turning
the ignition key to MAR, the warning light
turns on, but it should go off when the en-
gine has started.
If the warning light stays on or turns on
when travelling, means a fault in the sup-
ply/ignition system which could cause high
emissions at the exhaust, possible lack of
performance, poor handling and high con-
sumption levels.
The display will show the dedicated mes-
sage.
In these conditions it is possible to con-
tinue driving without however requiring
heavy effort or high speed from the en-
gine. Prolonged use of the car with the
warning light on may cause damages. Con-
tact Fiat Dealership as soon as possible.
The warning light turns off if the fault dis-
appears, but it is still stored by the system.
U
If, turning the ignition key to
MAR, the warning light U
does not turn on or if it turns
on glowing steadily or flash-
ing when travelling (on certain ver-
sions together with the message on
the display), contact Fiat Dealership
as soon as possible. Warning light U
operation can be checked by traffic
agents by proper equipment. Com-
ply with laws and regulations of the
country where you are driving.
Petrol engines only
Warning light turning on flashing indicates
the possibility of damage to the catalyst.
If the light flashes, it is necessary to release
the accelerator pedal to lower the speed
of the engine until the warning light stops
flashing; continue the journey at moder-
ate speed, trying to avoid driving condi-
tions that may cause further flashing and
contact Fiat Dealership as soon as possi-
ble.
FUEL RESERVE
(amber)
Turning the ignition key to
MARthe warning light turns on,
but it should go off after few seconds. The
warning light turns on when about 8 litres
fuel are left in the tank.
IMPORTANT The warning light flashes to
indicate a failure, contact Fiat Dealership
as soon as possible to have the system
checked.
ç
Always drive at a speed ap-
propriate to the traffic
conditions, the weather and speed
limits. The engine may be turned
off while the DPF light is on; how-
ever, repeated interruption of the
regeneration process may result in
premature exhaustion of engine oil.
For this reason it is always advisable
to wait for the light to go off before
turning off the engine, following the
instructions appearing above. It is
not advisable to complete DPF re-
generation with the vehicle sta-
tionary.
WARNING
141-154 BRAVO GB:141-154 BRAVO GB 11-11-2009 10:55 Pagina 148
Page 150 of 246

HILL HOLDER FAILURE
(amber)
The symbol
*will turn on
when the Hill Holder system is
faulty. Contact Fiat Dealership
as soon as possible.
On certain versions warning
light
áturns on as an alternative.
The display will show the dedicated mes-
sage.
149
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
WARNING
LIGHTS AND
MESSAGES
ESP SYSTEM
(amber)
Turning the ignition key to
MARthe warning light turns on,
but it should go off after few seconds.
If the warning light does not turn off or
stays on when travelling together with the
button led ASR, contact Fiat Dealership.
On certain versions the dedicated mes-
sage is displayed.
Warning light flashing when driving indi-
cates that the ESP system is active.
á
á
GLOW PLUG
WARMING
(Multijet versions)
(amber)
GLOW PLUG
WARMING FAILURE
(Multijet versions)
(amber)
Glow plug warming
Turning the ignition key to MARthe
warning light turns on and it will go off
when glow plugs reach the preset tem-
perature. Start the engine immediately af-
ter warning light turning off.
IMPORTANT With high ambient tem-
perature, warning light stays on for very
short time.
Glow plug warming failure
The warning light turns on when there is
a failure in the glow plug warming system.
Contact Fiat Dealership as soon as possi-
ble.
The display will show the dedicated mes-
sage.
m
*
WATER IN DIESEL
FUEL FILTER
(Multijet versions)
(amber)
Turning the ignition key to MARthe
warning light turns on, but it should go off
after few seconds.
The warning light turns on when there is
water in the diesel fuel filter.
The display will show the dedicated mes-
sage.
c
The presence of water in the
fuel circuit may cause serious
damage to the entire injec-
tion system and cause irreg-
ular engine operation. If the warning
light
cturns on (together with the
message on the display), contact Fi-
at Dealership as soon as possible to
have the system relieved. If the above
indications come on immediately af-
ter refuelling, water has probably
been poured into the tank: turn the
engine off immediately and contact
Fiat Dealership.
141-154 BRAVO GB:141-154 BRAVO GB 11-11-2009 10:55 Pagina 149
Page 153 of 246

152
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
WARNING
LIGHTS AND
MESSAGES
Check tyre pressure
The warning light (or the symbol on the
display) turns on to indicate that the tyre
pressure is below the recommended val-
ue which ensures the long life of the tyre
and optimum fuel consumption, and/or to
indicate a slow pressure leak.
Should two or more tyre be flat, the dis-
play will show the indications corre-
sponding to each tyre in sequence.
Restore proper inflation pressure values
as soon as possible (see paragraph “Cold
inflation pressures” in section “Technical
Specifications”).Tyre pressure unsuitable for speed
Should it be required to journey at a speed
higher than 160 km/h, inflate tyres at pres-
sures values specified in paragraph “Infla-
tion pressures”.
If the T.P.M.S. system (for versions/ mar-
kets, where provided) detects that the
pressure of one or more tyres is unsuit-
able for the current speed, the warning
light will turn on (together with the mes-
sage on the display) (see paragraph “Low
tyre pressure” in this section) and it will
stay on until the car speed slow downs be-
low the preset threshold.
IMPORTANT In this case slow down im-
mediately since tyre overheating could im-
pair tyre performance and life beyond re-
pair, and even make the tyre to blow-out.
Strong radio-frequency
noises could inhibit the reg-
ular operation of the T.P.M.S. sys-
tem. This condition will be indicat-
ed by a message (for versions/ mar-
kets, where provided). The warning
message will go off automatically as
soon as the radio-frequency noise
will stop to disturb the system.
WARNING
141-154 BRAVO GB:141-154 BRAVO GB 11-11-2009 10:55 Pagina 152
Page 157 of 246

156
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
ENGINE STARTING
EMERGENCY START-UP
If the instrument panel warning light
Yturns on glowing steadily, contact im-
mediately Fiat Dealership.
JUMP STARTING
If the battery is flat, it is possible to start
the engine using an auxiliary battery with
the same capacity or a little higher than
the flat one.
Proceed as follows fig. 1:
❒ Connect positive terminals (+ near the
terminal) of the two batteries with a
jump lead;
❒ With a second lead, connect the nega-
tive terminal (–) of the auxiliary battery
and to an earthing point
Eon the en-
gine or the gearbox of the car to be
started;
❒ Start the engine;
❒ When the engine has been started, re-
move the leads reversing the order
above.If after a few attempts the engine does not
start, do not insist but contact the near-
est Fiat Dealership.
IMPORTANT Do not directly connect the
negative terminals of the two batteries:
sparks could ignite the flammable gas from
the battery. If the other battery is fitted in
another car, prevent accidental contacts
between the metal parts of the two cars.BUMP STARTING
Never bump start the engine (by pushing,
towing, or coasting downhill) as this could
cause fuel to flow into the catalytic ex-
haust system and damage it beyond repair.
IMPORTANT Remember that the servo-
brake and electrical power steering sys-
tem are not operating until the engine is
started, a greater effort will therefore be
required to press the brake pedal or turn
the steering wheel.
fig. 1F0Q0733m
Under no circumstances
should a battery charger be
used to start the engine: it
could damage the electronic
systems and in particular the ignition
and injection control units.
Do not carry out this proce-
dure if you lack experience;
if it is not done correctly it can cause
very intense electrical discharges. In
addition, the fluid contained in the
battery is poisonous and corrosive.
Avoid contact with skin and eyes. You
are also advised not to put naked
flames or lighted cigarettes near the
battery and not to cause sparks.
WARNING
155-190 BRAVO GB.qxd 11-11-2009 10:55 Pagina 156
Page 184 of 246

183
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
COMPONENTS FUSE AMPERE FIGURE
Single-tone horn F10 10 51
Headlight alignment correction system
(versions with halogen headlights) F13 7.5 49
Conditioner compressor F19 7.5 51
Headlight washer motor pump F20 20 51
Fuel motor pump on tank F21 15 51
Remote switch coils on fuse box in engine compartment (CVM)/
Body Computer control unit (NBC) F31 5 49
Hi-Fi system subwoofer F32 15 49
Rear left power window F33 20 49
Rear right power window F34 20 49
Brake pedal control (normally closed contact NC)/
water in diesel fuel sensor/flow meter F35 5 49
155-190 BRAVO GB.qxd 11-11-2009 10:56 Pagina 183
Page 194 of 246

193
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
CAR
MAINTENANCE
SERVICE SCHEDULE
1.4 16V - 1.4 T-JET - 1.9 Multijet 8V - 1.9 Multijet 16V VERSIONS
30 60 90 120 150 180
●● ● ●● ●
●● ● ●● ●
●● ● ●● ●
●● ● ●● ●
●● ● ●● ●
●●●
●● ● ●● ●
●● ● ●● ●
●● ● ●● ●
●●●
●●
●●
●●
●●●
Thousands of km
Check tyre conditions/wear and adjust pressure if necessary
Check lighting system operation (headlights, direction indicators,
hazard lights, luggage compartment lights, passenger
compartment lights, glove compartment lights, instrument
panel warning lights, etc.)
Check operation of windscreen wiper system and
adjust sprays if necessary
Check position/wear of front/rear windscreen wiper blades
Check condition and wear of front disc brake pads and
operation of pad wear indicator
Check conditions and wear of rear disc brake pads
Visually check that the following are in good condition
and intact: body exterior, under body protection,
pipe rigid and flexible sections (exhaust-fuel system-brakes),
rubber parts (gaiters, sleeves, bushes, etc.)
Check cleanliness of locks, bonnet, engine and boot,
clean and lubricate linkages
Check and top-up fluids (hydraulic brakes/clutch,
windscreen washer, battery, engine coolant, etc.)
Check and adjust handbrake lever travel
Check visually conditions of auxiliary drive belt/s
Visually check conditions of toothed timing belt
(1.4 16V, 1.4 T-JET,1.9 Multijet 8V versions)
Check tension and adjust auxiliary drive belt
(except for engines with automatic tensioners)
Check and adjust tappet clearance (1.9 Multijet 8V version)
191-212 BRAVO GB:191-212 BRAVO GB 11-11-2009 10:56 Pagina 193
Page 195 of 246

194
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
CAR
MAINTENANCE
Thousands of km
Check exhaust emissions (petrol versions)
Check emissions/fumes (1.9 Multijet 8V - 1.9 Multijet 16V versions)
Check operation of engine control systems
(by means of test interface)
Replace accessory drive belt/s
Replace toothed timing belt (petrol versions) (*)
Replace toothed timing belt (1.9 Multijet 8Vversions) (*)
Replace toothed timing belt (1.9 Multijet 16Vversions) (*)
Replace spark plugs (petrol versions) 1
Replace fuel filter (1.9 Multijet 8V - 1.9 Multijet 16V versions)
Replace air filter cartridge (petrol versions)
Replace air filter cartridge (1.9 Multijet 8V - 1.9 Multijet 16V versions)
Replace engine oil and oil filter (petrol versions)
(or every 24 months) 2
Change engine oil and oil filter (
1.9 Multijet 8V - 1.9 Multijet 16V
versionswithout DPF) (or every 24 months)
Change engine oil and oil filter
(1.9 Multijet 8V - 1.9 Multijet 16V versionswith DPF) (**) 2
Change brake fluidr (or every 24 months)
Change pollen filter (or every 15 months)
(*) Irrespective of mileage, the timing drive belt must be replace every 4 years for heavy duty applications, cold climates, town use, long
periods idling) or at least every 5 years.
(**) The engine oil and oil filter should be changed depending on their actual condition, which is indicated by a warning light/message on the control panel or at
least every 2 years.
1For 1.4 T-JET versions, in order to ensure correct operation and avoid significant damages to the engine, it is mandatory:
- to use spark plugs specifically certified for the T-JET engine only, of the same type and brand (see paragraph “Engine”);
- to replace the plugs as often as required by the Programmed Maintenance Plan;
- we recommend to refer to the Fiat Dealership.
2If the car is used mainly on urban routes or if the yearly kilometres travelled are less than 10,000 km, the engine oil and filter must be changed every 12 months.
30 60 90 120 150 180
●● ● ●● ●
●● ● ●● ●
●● ● ●● ●
●
●
●
●
●● ● ●● ●
●●●
●●●
●●●
●● ● ●● ●
●● ● ●● ●
●●●
●●●
●●●●●●
191-212 BRAVO GB:191-212 BRAVO GB 11-11-2009 10:56 Pagina 194
Page 196 of 246

195
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
CAR
MAINTENANCE
1.6 Multijet and 2.0 Multijet VERSIONS
Thousands of km
Check tyre conditions/wear and adjust pressure if necessary
Check lighting system operation (headlights, direction indicators,
hazard lights, luggage compartment lights, passenger compartment lights,
glove compartment lights, instrument panel warning lights, etc.)
Check operation of windscreen wiper system and
adjust sprays if necessary
Check position/wear of front/rear windscreen wiper blades
Check condition and wear of front disc brake pads and operation
of pad wear indicator
Check conditions and wear of rear disc brake pads
Visually check that the following are in good condition
and intact: body exterior, under body protection,
pipe rigid and flexible sections (exhaust-fuel system-brakes),
rubber parts (gaiters, sleeves, bushes, etc.)
Check cleanliness of locks, bonnet, engine and boot,
clean and lubricate linkages
Check and top-up fluids (hydraulic brakes/clutch,
windscreen washer, battery, engine coolant, etc.)
Check and adjust handbrake lever travel
Check visually conditions of auxiliary drive belt/s35 70 105 140 175
●●●● ●
●●●● ●
●●●● ●
●●●● ●
●●●● ●
●●●● ●
●●●● ●
●●●● ●
●●●● ●
●●●● ●
●●
191-212 BRAVO GB:191-212 BRAVO GB 11-11-2009 10:56 Pagina 195
Page 197 of 246

196
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
CAR
MAINTENANCE
Thousands of km
Check emissions/fumes
Check operation of engine control systems
(by means of test interface)
Replace accessory drive belt/s
Replace toothed timing belt (*)
Replace fuel filter
Replace air filter cartridge
Change engine oil and oil filter (versions without DPF)
(or every 24 months)
Change engine oil and oil filter (versions with DPF) (**)
Change brake fluid (or every 24 months)
Change pollen filter (or every 15 months)
(*) Irrespective of mileage, the timing drive belt must be replace every 4 years for heavy duty applications, cold climates, town use, long periods
idling) or at least every 5 years.
(**) The engine oil and oil filter should be changed depending on their actual condition, which is indicated by a warning light/message on the
control panel or at least every 2 years.
If the car is used mainly on urban routes or if the yearly kilometres travelled are less than 10,000 km, the engine oil and filter must be changed
every 12 months.
35 70 105 140 175
●●●●●
●●●●●
●
●
●●
●●
●●●●●
●●
●●●●●
191-212 BRAVO GB:191-212 BRAVO GB 11-11-2009 10:56 Pagina 196