Specifications FIAT DOBLO 2008 1.G User Guide

152VEHICLE MAINTENANCE
ANNUAL
INSPECTION
SCHEDULE
For vehicles with an annual
mileage of below 20.000 km (for
example about 10.000 km) the
following yearly inspection pro-
gramme is advised:
– check tyre conditions/wear and ad-
just pressure if required (including the
spare wheel).
– check light system operation (head-
lights, direction indicators, hazard
lights, boot lights, passenger compart-
ment lights, glovebox light, warning
lights, etc.).
– check windscreen wiper/washer
operation, adjust nozzles.
– check windscreen/rear window
blade position/wear
– check front disk brake pad condi-
tions and wear.– check cleanness of bonnet and
boot locks and lever cleanness and lu-
brication
– sight inspect the conditions of: en-
gine, gearbox, transmission, pipes and
hoses (exhaust - fuel - brakes), rubber
parts (boots, sleeves, bushes, etc)
brake and fuel hoses.
– check battery charge.
– visual check on various drive belt
conditions.
– check and top up, if required, fluid
levels (engine coolant, brake fluid,
windscreen washer fluid, battery fluid,
etc.).
– change engine oil.
– change engine oil filter.
– replace pollen filter (where pro-
vided).
ADDITIONAL
CHECKS
Every 1,000 kmor before long
trips, check and top up as necessary:
engine coolant level, brake fluid level,
windscreen washer liquid level, tyre
pressure and conditions.
Every 3,000 km check and top up
as necessary: engine oil level.
You are recommended to use FL
Selenia,products designed and pro-
duced specifically for Fiat vehicles (see
“Capacities” in section “Technical
specifications”).
149-173 Doblo GB 9-05-2008 12:10 Pagina 152

157VEHICLE MAINTENANCE
ENGINE OIL fig. 6, 7, 8
Check engine oil with the vehicle on
level ground and while the engine is
still warm (approximately 5 minutes
after stopping the engine.
The oil level should be included be-
tween the MINand MAXreference
marks on the dipstick.
The space between MINand MAX
equals about 1 litre of oil.If the oil level is near or actually be-
low the MINmark, add oil through
the filler until it reaches the MAX
mark.
Oil level shall never exceed the
MAXmark. Be very careful under
the bonnet: you risk burn-
ing yourself. Remember
that when the engine is hot, the
fan can start up and cause in-
juries.
Do not add oil with dif-
ferent specifications from
the oil already in the en-
gine.
fig. 6 - 1.4 8V versions
F0A0536bF0A0346b
fig. 7 - 1.3 Multijet versions
149-173 Doblo GB 9-05-2008 12:10 Pagina 157

160VEHICLE MAINTENANCE
Prevent brake fluid,
which is highly corrosive,
from coming into contact
with painted parts. Should it hap-
pen, immediately wash with wa-
ter.
Check that fluid contained in tank is
at maximum level. If fluid has to be
added, it is suggested to use the brake
fluid in table "Fluids and lubricants"
(see chapter "Technical characteris-
tics"). At plug opening, pay maximum
attention in order to prevent any im-
purities from entering the tank.
For topping up, always use a funnel
with integrated filter with mesh equal
to or lower than 0.12 mm.
fig. 14
F0A0126b
POWER STEERING FLUID
fig. 13
The oil level with the vehicle on lev-
el ground and engine cold should be
included between the references MIN
and MAXon the reservoir.
When the oil is hot, the level can ex-
ceed the reference line MAX.
When topping up (where necessary)
make sure that the oil has the same
specifications as the oil in the system.Do not travel with the
windscreen washer reser-
voir empty. The wind-
screen washer is fundamental for
improving visibility.
fig. 13
F0A0261b
Do not let the power
steering fluid come into
contact with hot engine
parts. It catches fire very easily.
Oil consumption is ex-
tremely low. If the oil lev-
el needs topping up again
a s short period of time, have the
system checked for leakage at a
Fiat Dealership.
BRAKE/HYDRAULIC
CLUTCH FLUID fig. 14-15
Check that the level of the fluid in the
reservoir is at the maximum.
Use DOT 4 fluid only for topping up.
We recommend TUTELA TOP 4
that the braking system was originally
filled with.
149-173 Doblo GB 9-05-2008 12:10 Pagina 160

164VEHICLE MAINTENANCE
Incorrect fitting of elec-
trical and electronic ac-
cessories can seriously
damage the vehicle.
If after buying the vehicle, you
want to install electric acces-
sories which require permanent
electric supply (alarm, free-hand
phone kit, etc.) contact Fiat Deal-
ership whose qualified personnel,
in addition to suggesting the
most suitable devices, will evalu-
ate the overall electric absorp-
tion, checking whether the vehi-
cle electric system is capable of
withstanding the load required,
or whether it should be integrat-
ed with a more powerful battery.
Batteries contain sub-
stances that are very
harmful for the environ-
ment. You are advised to have
the battery changed at a Fiat
Dealership. It is properly
equipped for disposing of used
batteries in an environmentally-
friendly way that complies with
the law.The liquid in the battery
is poisonous and corro-
sive. Avoid contact with
eyes and skin. Do not bring naked
flames or possible sources of
sparks near the battery: risk of
fire and explosion.CHANGING THE BATTERY
If required, replace the battery with
a genuine spare part having the same
specifications.
If a battery with different specifica-
tions is fitted, the service intervals giv-
en in the “Service schedule” in this
section will no longer be valid. Refer
therefore to the instructions provid-
ed by the battery manufacturer.
Running the battery
with low fluid level can
damage the battery be-
yond repair and could also cause
its explosion.
149-173 Doblo GB 9-05-2008 12:10 Pagina 164

171VEHICLE MAINTENANCE
ADVICE FOR PRESERVING
THE BODYWORK
Paint
Paintwork does not only serve an
aesthetic purpose, but also protects
the underlying sheet metal.
In the case of deep scrapes or scores,
you are advised to have the necessary
touching up carried out immediately
to avoid the formation of rust.
Only use genuine products when
touching up the paintwork (see “Body-
work paint identification plate” in sec-
tion “Technical specifications”).
Ordinary maintenance of the paint-
work means washing it. The frequen-
cy you should do this depends on the
conditions and the environment the
vehicle is driven in. For example, in ar-
eas with a high level of air pollution or
on roads sprinkled with road salt,
wash the vehicle more frequently. – The spraying of the underbody, en-
gine compartment, inside the wheel-
houses and other parts with wax-
based products with a high protective
capacity.
– Spraying plastic-coating materials
to protect the most exposed points:
under the door, inside the wings, the
edges etc.
– The use of “open” box sections to
prevent condensation and water from
building up and rusting the inside of
the parts.
BODY AND UNDERBODY
WARRANTY
Your Fiat Doblò is covered by war-
ranty against any original structural or
body part being perforated by rust.
Refer to the Warranty Booklet for the
general terms.BODYWORK
PROTECTION FROM
ATMOSPHERIC AGENTS
The main causes of rust are:
– atmospheric pollution
– salt and humidity in the atmosphere
(coastal or very hot and humid areas)
– environmental conditions that are
specific to the season.
Not to be underestimated is also the
abrasive action of wind-borne atmos-
pheric dust and sand and mud and
gravel raised by other vehicles.
For your Fiat Doblò, Fiat has used
leading-edge technological solutions to
effectively protect the body from rust.
These include:
– Painting systems and products that
make the vehicle particularly resistant
to rust and scratching.
– The use of zinc-plated sheet steel
which is highly resistant to rust.
149-173 Doblo GB 9-05-2008 12:10 Pagina 171

174TECHNICAL SPECIFICATIONS
VEHICLE IDENTIFICATION
DATA CHASSIS MARKING
fig. 1
It is printed on the passenger com-
partment floor, near the right-hand
front seat.
It can be reached by lifting the spe-
cial flap in the carpeting and includes
the following data:
– vehicle model ZFA 223000;
– chassis number.MODEL PLATE
The plate A-fig. 2-3, is applied to the
front engine crossmember.
T T
E E
C C
H H
N N
I I
C C
A A
L L
S S
P P
E E
C C
I I
F F
I I
C C
A A
T T
I I
O O
N N
S S
fig. 1
F0A0163b
fig. 2 - 1.4 8Vversions
F0A0537b
fig. 3 - Multijet versions
F0A0538b
ENGINE MARKING
The marking is stamped on the cylin-
der block and includes the model and
the serial number.
174-211 Doblo GB 16-12-2008 14:26 Pagina 174

The plate fig. 4bears the following
identification data:
B - Homologation number
C - Vehicle type code
D - Chassis number
E - Maximum vehicle weight fully
loaded
F- Maximum vehicle weight fully
loaded with trailer.G- Maximum vehicle weight on
front axle.
H - Maximum vehicle weight on rear
axle
I - Engine type
L - Body version code
M - Spare part code
M - Smoke opacity index (for diesel
engines).BODYWORK PAINT
IDENTIFICATION PLATE
The plate fig. 5is applied inside the
bonnet.
It bears the following data:
A - Paint manufacturer
B - Colour name
C - Fiat colour code
D- Respray and touch up code.
fig. 4
F0A0722bA
B
C
D
fig. 5
F0A0169b
175TECHNICAL SPECIFICATIONS
174-211 Doblo GB 16-12-2008 14:26 Pagina 175

176TECHNICAL SPECIFICATIONS
ENGINE CODES - BODYWORK VERSIONS
EUROPEAN HOMOLOGATION
Engine Engine code
1.4 8V 350A1000
Versions Bodywork
version code
Cargo 223ZXP1AAX
Cargo high roof 223ZXP1ABX
Cargo extra capacity 223WXP1AAX
Cargo high roof - extra capacity 223WXP1ABX
Cargo small capacity 223ZXP1AAY
Cargo high roof - small capacity 223ZXP1ABY
Cargo Maxi (long wheelbase) 223WXP1AAXL
Cargo Maxi (long wheelbase) - small capacity 223WXP1AAYL
5 seater combi N1 223WXP1AAZ
Panorama 223AXP1A10
Panorama high roof 223AXP1A10B
7 seater family 223AXP1A10C
HOMOLOGATION FOR SPECIFIC MARKETS
Engine Engine code
1.4 8V 350A1000
Versioni Bodywork
version code
Cargo 223ZXP1AXX
Cargo high roof 223ZXP1AXY
Cargo extra capacity 223WXP1AXX
Cargo high roof - extra capacity 223WXP1AXY
Cargo Maxi (long wheelbase) 223WXP1AXXL
5 seater combi N1 223WXP1AXZ
Panorama 223AXP1AXX
Panorama high roof 223AXP1AXXB
7 seater family 223AXP1AXXC
174-211 Doblo GB 16-12-2008 14:26 Pagina 176

177TECHNICAL SPECIFICATIONS
EUROPEAN HOMOLOGATION
Engine Enginecode
1.3 Multijet 199 A 2000
Versions Bodywork
version code
Cargo 223ZXN1AAX
Cargo high roof 223ZXN1ABX
Cargo extra capacity 223WXN1AAX
Cargo high roof - extra capacity 223WXN1ABX
Cargo small capacity 223ZXN1AAY
Cargo high roof - small capacity 223ZXN1ABY
Cargo Maxi (long wheelbase) 223WXN1AAXL
Cargo Maxi (long wheelbase) - small capacity 223WXN1AAYL
5 seater combi N1 223WXN1AAZ
Engine Engine
code
1.3 Multijet 85 HP 223 A 9000
Versions Bodywork
version code
Cargo 223ZXM1AAX
Cargo high roof 223ZXM1ABX
5 seater combi N1 223ZXM1AAZ
Panorama 223AXM1A08D
Panorama high roof 223AXM1A08B
7 seater family 223AXM1A08E
HOMOLOGATION FOR SPECIFIC MARKETS
Engine Enginecode
1.3 Multijet 199 A 2000
Versions Bodywork
version code
Cargo 223ZXN1AXX
Cargo high roof 223ZXN1AXY
Cargo extra capacity 223WXN1AXX
Cargo high roof - extra capacity 223WXN1AXY
Cargo Maxi (long wheelbase) 223WXN1AXXL
5 seater combi N1 223WXN1AXZ
174-211 Doblo GB 16-12-2008 14:26 Pagina 177

178TECHNICAL SPECIFICATIONS
EUROPEAN HOMOLOGATION
Engine Engine code
1.9 Multijet 105 HP 223 B 1000
Versions Bodywork
version code
Cargo 223ZXL1AAX
Cargo high roof 223ZXL1ABX
Cargo extra capacity 223WXL1AAX
Cargo high roof - extra capacity 223WXL1ABX
Cargo small capacity 223ZXL1AAY
Cargo high roof - small capacity 223ZXL1ABY
Cargo Maxi (long wheelbase) 223WXL1AAXL
Cargo Maxi (long wheelbase) - small capacity 223WXL1AAYL
5 seater combi N1 223WXL1AAZ
Panorama 223AXL1AA07
Engine Engine
code
1.9 Multijet 100 HP 223 B 2000
Versions Bodywork
version code
Cargo 223ZXR1AAX
Cargo high roof 223ZXR1ABX
Cargo extra capacity 223WXR1AAX
Cargo high roof - extra capacity 223WXR1ABX
Cargo Maxi (long wheelbase) 223WXR1AAXL
HOMOLOGATION FOR SPECIFIC MARKETS
Engine Engine code
1.9 Multijet 105 HP 223 B 1000
Versions Bodywork
version code
Cargo 223ZXL1AXX
Cargo high roof 223ZXL1AXY
Cargo extra capacity 223WXL1AXX
Cargo high roof - extra capacity 223WXL1AXY
Cargo Maxi (long wheelbase) 223WXL1AXXL
5 seater combi N1 223WXL1AXZ
Panorama 223AXL1AXX
174-211 Doblo GB 16-12-2008 14:26 Pagina 178