ENGINE FIAT DOBLO 2008 1.G Manual PDF

179TECHNICAL SPECIFICATIONS
EUROPEAN HOMOLOGATION
Engine Engine code
1.9 Multijet 120 HP 186 A 9000
VersionsBodywork version code
Cargo 223ZXH1AAX
Cargo high roof223ZXH1ABX
Cargo Maxi (long wheelbase)223ZXH1AAXL
5 seater combi N1223ZXH1AAZ
Panorama 223AXH1A06
Panorama high roof223AXH1A06B
7 seater family223AXH1A06C
ENGINE
GENERAL FEATURES1.4 8v
Type code 350A1000
Cycle Otto
Number and layout of cylinders 4 in line
Piston bore and stroke mm 72,0 x 84
Total displacement cm31368
Compression ratio 11,1 : 1
Max power (CEE):
kW 57
HP 77
corresponding ratio rpm 6000
Max torque (CEE):
Nm 115
kgm 11,7
corresponding ratio giri/min 3000
Spark plugs NGK ZKR7A - 10
Fuel Unleaded
petrol
95 RON
174-211 Doblo GB 16-12-2008 14:26 Pagina 179

Modifications or repairs
to the fuel system that
are not carried out prop-
erly or do not take the system
technical specifications into ac-
count can cause malfunctions
leading to the risk of fire. FUEL SUPPLY/IGNITION
Petrol versions
Electronic Multipoint sequential
phased injection integrated with igni-
tion, returnless system.FUEL FEED/IGNITION
Multijet versions
“Common Rail” electronic control
direct injection, turbo and intercool-
er.
SPARK PLUGS
The cleanness and soundness of the
spark plugs are very important for
keeping the engine efficient and pol-
luting emissions down.
The appearance of the spark plug, if
examined by an expert eyes, is a good
way of pinpointing a problem even if it
has nothing to do with the ignition sys-
tem. Therefore, if the engine has prob-
lems, it is important to have the spark
plugs checked at a Fiat Dealership.
The spark plugs must be
changed at the times
specified in the service
schedule. Only use the type of
plugs indicated. If the heat ratio
is less than required or the life
specified is not guaranteed, prob-
lems can arise.
181TECHNICAL SPECIFICATIONS
174-211 Doblo GB 16-12-2008 14:26 Pagina 181

200TECHNICAL SPECIFICATIONS
CAPACITIES
1.4
litres kg
60 –
5 - 7 –
7–
2.4 2.1
2.6 2.25
1.98 1.8
1.3 1.2
0.5 –
0.55 –
7–
Fuel tank:including a reserve of:
Engine cooling
system:
Engine sump:
Engine sump and filter:
Manual gearbox:
Power steering
Front and rear brakes
hydraulic circuit:
Hydraulic brake circuit
with ABS:
Windscreen and rear window
washer fluid reservoir:
(▲) For particularly hard climate conditions, we recommend use of a 60% PARAFLU UP and 40% demineralized water mixture.
(❒) For particularly cold temperatures use SELENIA MULTIPOWER.
Prescribed fuel
Recommended products
Unleaded petrol not lower than
95 R.O.N
50 - 50 mixture of distilled water
and PARAFLU UP
(▲)
SELENIA 20K(❒)
TUTELA CAR ZC 75 SYNTH
TUTELA GI/E
TUTELA TOP 4
TUTELA TOP 4
Mixture of water and TUTELA
PROFESSIONAL SC 35
174-211 Doblo GB 16-12-2008 14:26 Pagina 200

201TECHNICAL SPECIFICATIONS201
1.9 Multijet
litres kg
60 –
5 - 7 –
6.5 –
4.0 (❍) 3.5 (❍)
4.3 (❍) 3.7 (❍)
1.98 1.8
1.3 1.2
0.5 –
0.55 –
7– 1.3 Multijet
litres kg
60 –
5 - 7 –
6.5 –
3.0 (■) 2.6 (■)
3.2 (■) 2.8 (■)
1.98 1.8
1.3 1.2
0.5 –
0.55 –
7–
(▲) For particularly hard climate conditions, we recommend use of a 60% PARAFLU UP and 40% demineralized water mixture.
(❍) For particularly cold temperatures use SELENIA WR.
Fuel tank:including a reserve of:
Engine cooling
system:
Engine sump:
Engine sump and filter:
Manual gearbox:
Power steering
Front and rear brakes
hydraulic circuit:
Hydraulic brake circuit
with ABS:
Windscreen and rear window
washer fluid reservoir: Prescribed fuel
Recommended products
Diesel fuel for motor vehicles
(EN590 Specification)
50 - 50 mixture of distilled water
and PARAFLU UP
(▲)
SELENIA TURBO DIESEL(❍)
SELENIA WR(■)
TUTELA CAR ZC 75 SYNTH
TUTELA GI/E
TUTELA TOP 4
TUTELA TOP 4
Mixture of water and TUTELA
PROFESSIONAL SC 35
174-211 Doblo GB 16-12-2008 14:26 Pagina 201

202TECHNICAL SPECIFICATIONS
FLUIDS AND LUBRICANTS
PRODUCTS WHICH MAY BE USED AND THEIR CHARACTERISTICS
Specifications of the lubricants and fluids to use
for best operation
Synthetic-based engine oils grade SAE 10W-40
that pass ACEA A3 and API SL specifications.
Synthetic-based engine oils grade SAE 5W-30
that pass ACEA A1-A5 - API SL and
FIAT 9.55535-M1specifications.
Synthetic-based engine oils grade SAE 10W-40
that pass ACEA B3 and API CD specifications.
Synthetic-based engine oils grade SAE 5W-40
that pass ACEA B4, API CF and
FIAT 9.55535-M2specifications.
Synthetic-based engine oils grade SAE 5W-40 that pass
ACEA B4, API CF and FIAT 9.55535-M2specifications
F0A0175b
(*) For very low temperatures, we recommend SELENIA MULTIPOWER.
(**) For very low temperatures, we recommend SELENIA WR.
Applications Use
Lubricants for
petrol engines (*)
Lubricants for
diesel engines (**)
Lubricants for
diesel engines
(1.3 Multijet versions)
Fluids and lubricants
recommended
SELENIA 20K
SELENIA
MULTIPOWER
SELENIA
TURBO DIESEL
SELENIA
WR
174-211 Doblo GB 16-12-2008 14:26 Pagina 202

204TECHNICAL SPECIFICATIONS
FUEL CONSUMPTION
The fuel consumption and CO2emis-
sion values listed in the table below are
determined based on homologation
tests laid down in the European Di-
rective 2004/3/EC.
To measure fuel consumption and
emissions the procedures below are
followed:
– Urban cycle:the vehicle is start-
ed with the engine cold and driven so
as to reproduce the speed and
gearshift profile specified in the Euro-
pean Directive. The cycle includes a
series of accelerations, decelerations,
driving at constant speed and standing
with the engine in idle. The maximum
speed reached during the cycle is
50km/h and the average speed is
19km/h.– Extraurban cycle:consecutive to
the urban cycle according to the spec-
ifications laid down in the European
Directive. The maximum speed
reached during the cycle is 120km/h
and the average speed is 63km/h.
– consumption:this is determined
through a weighted average of the
consumption measured for the urban
cycle (with approx. 37% weight) and
for the extraurban cycle (with approx.
63% weight).
IMPORTANT
In practice, fuel consumption may be
higher than the values determined
through the homologation tests. Be-
low are some of the main factors that
may result in a deviation between the
consumption measured during normal
use of the vehicle and that measured
during the homologation tests.1) Vehicle conditions: inadequate
maintenance, use of roof racks, trail-
ers, heavy load conditions, intense use
of the electrical devices and the air-
conditioning.
2) Driving style: frequent cold starts
to drive short stretches, incorrect
procedure to warm up the engine,
gearshifting, continuous driving at high
speeds, sudden acceleration and brak-
ing.
3) Traffic and road conditions: driving
in traffic, uphill or twisty roads, road
surface conditions.
4) Atmospheric conditions: intem-
perate climate, wind, rain, snow, dri-
ving at high altitudes.
5) Percentage town, out-of-town and
motorway driving.
174-211 Doblo GB 16-12-2008 14:26 Pagina 204

205TECHNICAL SPECIFICATIONS205
PRACTICAL TIPS TO
REDUCE CONSUMPTION
AND ENVIRONMENTAL
POLLUTION
Vehicle conditions
1. Have checks and adjustments
carried out in accordance with the
“Scheduled Service Plan”.
2. Check the tyre pressure at inter-
vals of not more than 4 weeks (see
“Tyre pressure”). Too low tyre pres-
sure increases consumption as the
rolling resistance increases. In these
conditions the tyres wear faster and
performance deteriorates.
3. Use winter tyresonly in the sea-
sons where dictated by the climatic
conditions. Winter tyres not only in-
crease consumption but also tyre
noise.4. Do not travel in heavy load con-
ditions(vehicle overloaded): The
weight of the vehicle (especially when
driving in town) and its trim greatly af-
fect fuel consumption and stability.
5. Remove roof racks or ski racks
after use. These accessories reduce
the aerodynamics of the vehicle and
have a negative effect on fuel con-
sumption.
6. Ideally use a trailerto transport
particularly bulky objects.
7. It is preferable to use the air vents:
driving with the window open has a
negative effect on the aerodynamics of
the vehicle.
8. Use the electrical devices only for
the time strictly necessary. The rear
heated window, additional headlights,
windscreen wipers and heater fan
need a considerable amount of ener-
gy, consequently increasing fuel con-
sumption (up to 25% more in the ur-
ban cycle).9. Using the air-conditioning in-
creases consumption (up to 30% more
on average): use the air vents when
the outside temperature permits.
Driving style
1. After starting the engineit is
advisable to set off immediately and
slowly avoiding revving up the engine.
Do not warm up the engine with the
vehicle stationary either at idle or at
high speed: in these conditions the en-
gine in fact warms up more slowly, in-
creasing consumption, emissions and
wear of the mechanical devices.
2. Avoid revving upwhen starting
at traffic lights or before turning off the
engine. This action, like double-de-
clutching, is unnecessary and causes in-
creased fuel consumption and pollu-
tion.
174-211 Doblo GB 16-12-2008 14:26 Pagina 205

206TECHNICAL SPECIFICATIONS
3. Gear selection: change to the
highest gear as soon as possible (con-
sistent with smoothness of engine op-
eration and the traffic conditions) and
do not push the engine to high speeds
in the intermediate gears. Engaging low
gears at high speeds to achieve super
acceleration increases consumption,
polluting emissions and engine wear.
4. Vehicle speed: fuel consumption
increases exponentially as the speed
increases. Keep your speed as mod-
erate and constant as possible, avoid-
ing unnecessary braking and acceler-
ation, which cause excessive fuel con-
sumption and increased emissions.
Keeping an adequate safety distance
from the vehicle in front of you will
help smoother driving.5. Acceleration: violently acceler-
ating considerably affects consumption
and emissions; therefore, accelerate
gradually without exceeding the max-
imum torque speed of the engine.CO2EMISSIONS
The values were obtained from
analysis of the exhaust gas emitted
during the test and are related to the
consumption values through the car-
bon balance of the emissions pro-
duced.
The CO
2emission values listed in the
following table refer to combined con-
sumption.
174-211 Doblo GB 16-12-2008 14:26 Pagina 206

211TECHNICAL SPECIFICATIONS
PROVISIONS FOR THE PROCESSING OF A VEHICLE
AT THE END OF ITS LIFE-CYCLE
For years now Fiat has been developing its global commitment towards the safeguarding and protection of the
Environment through the continuous improvement of its production processes and the making of increasingly more “eco
friendly” products. With a view to guaranteeing the best possible service to clients in full observance of environmental
standards and in response to the obligations imposed by European Directive 2000/53/EC on end-of-life vehicles, Fiat offers
its clients the possibility to hand in their vehicle* at the end of its life span without additional costs.
The European Directive, in fact, provides for the take-back of the vehicle without the last holder or owner of the same
incurring expenses due to the fact that the market value of the vehicle is zero or negative. In particular, in almost all of
the countries of the European Union, up until 1st January 2007, take-back of the vehicle free of charge only applies to vehi-
cles registered from 1 July 2002 on, while, from 2007 on, take-back will be carried out free of charge, independently of
the year of registration, provided that the vehicle still contains all its essential component parts (especially engine and
body) and is free from additional waste materials.
Our contracted network of authorised treatment facilities has been carefully selected in order to provide a quality ser-
vice to our customers by de-polluting and recycling “End of Life Vehicles” to approved environmental standards. To find
out the location of your nearest authorised treatment facility, offering free of charge take-back, simply contact one of our
dealers or refer to the Fiat web site or call the toll free number 00800 3428 0000.
*Passenger transportation vehicles to seat a max. of nine persons, having a total admissible weight of 3.5 t
174-211 Doblo GB 16-12-2008 14:26 Pagina 211

213INDEX
- rear window ............................. 61
- windscreen ............................... 60
Digital clock .......................... 26-27
Dimensions ................................... 187
Direction indicators
- control ...................................... 64
- front bulb replacement .......... 133
- rear bulb replacement ........... 134
- side bulb replacement ............ 134
Door lock/unlock
remote control ............................. 8
Double ladder (partitions) ......... 51
Driver’s protection ladder
(partitions)................................... 51
Driving your vehicle .................... 106
EBD electronic brake force
distributor ................................... 90
Electric windows .......................... 74
Electronic brake force
distributor EBD .......................... 90
Electronic control units .............. 166
Engine
- fuel feed ..................................... 181
- identification code .................. 176
- ignition ...................................... 181
- specifications ............................ 179Engine compartment
- washing ...................................... 172
Engine coolant gauge ................... 25
Engine coolant level ..................... 159
Engine oil
- checking the level.................... 157
- consumption............................. 158
- specifications ............................ 202
Engine oil level .............................. 157
EOBD system................................ 97
Evaporation system...................... 104
Exhaust gas recirculation ............ 104
Extending the boot ...................... 80
Fiat CODE system ..................... 6
First aid kit ..................................... 148
Follow me home ......................... 66
Front doors ................................... 74
Front foglights
- bulb replacement ................... 133
- control button ......................... 68
Fuel
- at the filling station ................. 102
- capacities .................................. 200
- fuel cut-off switch ................... 69
- gauge .......................................... 25
Fuel cap........................................... 103Fuel consumption ......................... 204
Fuel cut-off switch........................ 69
Fuses
- dashboard fusebox.................. 139
- engine compartment
fusebox ...................................... 140
- replacement.............................. 138
- table............................................ 141
Gearbox
- gearbox use .............................. 109
- technical characteristics ........ 182
Getting to know your vehicle ... 6
Glove compartment .................... 69
Handbrake .......................... 107-182
Hazard lights.................................. 68
Headlight beam corrector.......... 88
Headlight slant
(electrical corrector) ................ 88
Headlights
- adjusting the headlights
abroad........................................ 89
- beam corrector ....................... 88
- beam direction......................... 89
- slant compensation ................. 88
Head restraints
212-220 Doblo GB 16-12-2008 14:26 Pagina 213