fold seats FIAT DOBLO PANORAMA 2015 2.G Owners Manual

.
BONNET OPENING LEVER
❒Opening/closing .................................. 59
STEERING WHEEL
ADJUSTMENT UNLOCKING LEVER
❒Operation ........................................... 32
DOORS
❒Lock/Unlock ....................................... 19
SEATS
❒Adjustments ....................................... 24❒Driver’s seat adjustments .................... 24
❒Passenger seat adjustments ............... 25
❒Rear seat access ................................ 26
❒Seat that folds to table ........................ 26
❒Third row seats ................................... 26
4F0V0541
12
GRAPHICAL INDEX

Driver seat lumbar
adjustment
(for versions/markets, where
provided)
Turn knob D fig. 25 to adjust the
backrest support.
Heated seats
(for versions/markets, where
provided)
With the key turned to MAR, press
button A fig. 26 to switch the
function on/off.
When the function is enabled, the
LED on the button turns on.FOLDAWAY
PASSENGER SEAT
(for versions/markets, where
provided)
The passenger seat can be folded
away on some Cargo versions.
17)
Completely retract the seat for a
total folding down avoiding
interference with the dashboard.
Seat folding
To fold the seat, proceed as follows:
❒open the passenger side door;
❒pull levers A and fold the backrest
forwards in the direction indicated
by the arrow;
❒then push the backrest B fig.
28down: the seat is now completely
folded over on itself into the "table"
position;
❒pull flap C fig. 29 and push the
backrest down further: the seat
is now completely folded away.
26F0V0208
27F0V0142
28F0V0143
25

Repositioning the seat
To return the seat back to its
normal position, proceed as follows:
❒grip tab A fig. 30 and lift the backrest
upwards;
❒operate levers B fig. 31 and lift the
seat further upwards.
18) 19)
ACCESS TO THE REAR
SEATS
(Doblò and Doblò Combi versions)
To access the rear seats, open
one of the sliding side doors (see
"Doors" in this section).
FOLDING TABLE SEAT
(Doblò and Doblò Combi versions,
where provided)
On some versions the seat can be
folded into a table position.
20)
Completely retract the seat in table
position for a total folding down
avoiding interference with the
dashboard.
IMPORTANT Move the seat only
when there are no rear passengers.Seat folding
❒Open the passenger side door;
❒Pull lever A fig. 32 and fold the
backrest forwards in the direction
indicated by the arrow;
❒Push the backrest B fig. 32 down:
the seat is now completely folded
over on itself into the "table" position.
Repositioning the seat:
❒operate lever A fig. 32 and lift the
backrest upwards.
3RD ROW SEAT
MOVEMENTS
Proceed as follows:
❒completely lower the rear seat head
restraints;
29F0V0144
30F0V0145
31F0V0146
32F0V0201
26
KNOW YOUR VEHICLE

❒move the seat belt to the side,
making sure that it is fully extended
and not twisted;
❒lift lever A fig. 33 retaining the
backrest and fold the latter forwards.
When you lift the lever, you will see
a red band.
❒pull the tape B fig. 33 behind the seat
backrests and fold the seats and the
backrests forwards.NoteOn the split seats, there are
rubber bands on the lower edge of the
cushion so you can attach the folded
seat to the 2nd row rear seat head
restraint rods (see the plate on the seat
backrest fig. 33).
21)
REMOVING 3RD ROW
SEATS
Proceed as follows:
❒remove the rear seat head restraints;
❒remove the rolling curtain from its
housing;
❒move the seat belt to the side,
making sure that it is fully extended
and not twisted;
❒lift lever A fig. 33 retaining the
backrest and fold the latter forwards.
When you lift the lever, you will see
a red band.
❒pull the tape B fig. 33 behind the seat
backrests and fold the seats and the
backrests forwards;
❒position the head restraint using the
openings under the cushion to insert
the rods;
❒push the lever as indicated in fig. 35;
❒remove the seat from the
attachments on the floor.REPOSITIONING 3RD
ROW SEATS
Proceed as follows:
❒attach the hooks to the floor fig. 36;
❒push the lever as illustrated in fig.
35 and pull it to make sure that
the seat is still correctly secured;
❒withdraw the head restraint under the
cushion;
3
124
12437856
33F0V0407
34F0V0408
35F0V0206
36F0V0207
27

WARNING
15) All adjustments must be made
with the vehicle stationary.
16) After releasing the adjustment
lever, always check that the seat
is locked on the guides by trying
to move it back and forth. If it
is not locked, the seat may move
unexpectedly and make you lose
control of the vehicle.
17) Close the dashboard console
before folding the retractable
front passenger seat to avoid
damage.
18) When the passenger seat is
folded away, the space created
cannot be used for loading. When
the vehicle is in motion, you are
therefore advised to remove or
secure any objects that might
interfere with the driver.19) If there is no partition between
the cab and the load
compartment, tall objects or
packages may take up part of the
passenger area. Make sure that
these items are well secured
by using the available hooks and
that they cannot interfere with the
driver.
20) Close the dashboard console
before folding the front passenger
seat into table position to avoid
damage.
21) While travelling, before using the
third row seats, make sure that
the second row seats are in
driving position and correctly
secured (see dedicated plate fig.
34.
PARTITIONS
FIXED PANEL
PARTITION
(for versions/markets, where
provided)
Separates the passenger area from
the load compartment fig. 40.
FIXED GLAZED
PARTITION
(for versions/markets, where
provided)
This has a central window so you
can keep an eye on your load fig.
41.
40F0V0102
29

EMERGENCY OPENING
FROM THE INSIDE
In the event of an emergency, you
can open the boot from inside
the vehicle as follows:
❒open the sliding side door and fully
fold the rear seats;
❒from inside the boot, press lever A
fig. 78 and open the tailgate.
EMERGENCY OPENING
OF THE SWING DOORS
FROM THE INSIDE
In the event of an emergency, you
can open the boot from inside
the vehicle as follows:
❒open the sliding side door and lower
the backrest of the rear seat to give
you access to the load compartment
(Doblò/Doblò Combi versions);
or
❒open the sliding side door (Cargo
versions);
❒use device A fig. 79 located on the
inside of the right-hand swing door;
❒open the left-hand swing door by
pulling on its handle (see "Doors"
in this section).
REMOVING THE
PARCEL SHELF
The parcel shelf consists of two
parts. To remove it completely,
proceed as follows:
❒open the rear swing door; raise the
front part A fig. 80, unhooking pin A
fig. 81 from its housing
❒raise rear part B fig. 80, unhooking
pins B and C fig. 81 from their
housings.
If the seat is completely folded
down, remove the parcel shelf as
described and store it horizontally
between the back of the front seats
and the folded rear seat.
To refit the parcel shelf, follow the
same procedure in reverse.
76F0V0370
77F0V0340
78F0V013579F0V0080
61

EXTENDING THE BOOT
Proceed as follows:
❒open the rear doors and remove the
parcel shelf (as described previously);
❒completely lower the rear seat head
restraints;
❒move the seat belt to the side,
making sure that it is fully extended
and not twisted;❒lift backrest retainer lever A fig. 82
and fold the backrest forwards to
give you a flat loading area. When
you lift the lever, you will see a red
band.
❒to widen the load compartment
further, lift lever B fig. 83 on the side
of the cushion that will raise
automatically; intervene manually to
fold seat and backrest completely
forward fig. 84.
On versions with backrest folded
down and parcel shelf folded down
(for versions/markets, where
provided) a load compartment can
be created fig. 85.
In the low position, the parcel shelf
can support a maximum load of
70 kg on a minimum bearing surface
of 400 mm × 400 mm fig. 86.
N.B. There are bands on the rear
seats under the cushion to attach
the folded seat to the front seat
head restraint rods.
80F0V0136
81F0V0137
82F0V0127
83F0V0202
84F0V0203
62
KNOW YOUR VEHICLE

38) Never exceed the maximum
allowed load in the boot (see
the "Technical specifications"
chapter). Also make sure that the
objects you place in the boot
have been properly secured, to
avoid them from being thrown
forward consequent to sudden
braking and injuring your
passengers.
39) You must not use the folded
rear seat to carry luggage. The
load could be thrown forward into
the backrest of the front seats,
seriously injuring the occupants.
40) Make sure that the objects are
positioned carefully and fixed to
the hooks on the floor to prevent
them being flung forwards in
the event of sharp braking and
causing injury to the passengers.
IMPORTANT
7) To close the tailgate use handle B
fig. 77. Do not try to close the
tailgate by pressing on the side
shock absorbers C fig. 77. Also be
careful not to knock the side
shock absorbers when you load
the boot, to avoid damaging them.
INTERIOR FITTINGS
DRIVER SIDE ARMREST
(for versions/markets, where
provided)
On some versions, the driver side
front seat has an armrest fig. 89.
Raise or lower the armrest as shown
by the arrows.
GLOVE COMPARTMENT
(for versions/markets, where
provided)
This is located in front of the
passenger seat fig. 90.GLOVE COMPARTMENT
To open it, operate handle A fig.
91.
Turn the key clockwise/
anticlockwise to lock/unlock the
glove compartment (for
versions/markets where provided).
41)89F0V0058
90F0V0059
91F0V0060
64
KNOW YOUR VEHICLE

IMPORTANT The backrest is
correctly secured when the red
band fig. 122 on backrest folding
handles A disappears. This red band
indicates that the backrest is not
secured.IMPORTANT After putting the rear
seats (for Doblò/Doblò Combi
versions) back to their normal
operating position, refit the seat belt
so that it is ready for use.
63)
ADJUSTING THE SEAT
BELT HEIGHT
64) 65)
The seat belt height can be adjusted
to various positions using the
regulator on the central pillar.
Always adjust the height of the seat
belts to fit the person wearing it:
this precaution could greatly reduce
the risk of injury in the event of
collision.
Correct adjustment is obtained
when the belt passes approximately
half way between the shoulder
and the neck.
WARNING
61) Never press button C fig. 119
when travelling.
62) Remember that, in the event of a
violent collision, back-seat
passengers not wearing seat belts
represent a serious danger to
the front-seat passengers as well
as to themselves.
63) Make sure that the backrest is
correctly secured on both sides
(red bands B not visible) to
prevent it from moving forward in
the event of sharp braking,
causing injuries to passengers.
64) The height of the seat belts must
be adjusted with the vehicle
stationary.
65) After the height adjustment,
always check that the regulator is
locked in one of the preset
positions. To do this, push
downwards to enable the locking
device to click if the grip has
not been released in one of the
possible positions.
121F0V0197
122F0V0127
116
SAFETY

ISOFIX CHILD
RESTRAINT SYSTEM
SETUP
(for versions/markets, where
provided)
Only for vehicles designed to carry
people, (homologation M1),
provision has been made on some
versions to fit a Universal Isofix child
restraint system, a new European
standardised system for carrying
children safely.
Isofix systems can be fitted
alongside a traditional child restraint
system. An example of a child
restraint system is shown in fig. 130.
The Universal Isofix child restraint
system covers weight group 1.
Specific Isofix child restraint systems
cover the other weight groups.
These seats must be designed,
tested and type-approved
specifically for this vehicle (refer to
the list of vehicles attached to the
child restraint system).Due to its different anchoring
system, the child restraint system
must be attached to the dedicated
lower metal rings A fig. 131, located
between the backrest and rear
cushion. After removing the rear
parcel shelf (if present), secure the
upper belt (provided with the child
restraint system) to ring B fig. 132
(one on each side) located behind
the rear seat cushion.
NoteTo prevent possible scoring of
the table seat backrest, with folded
rear seat (for versions/markets,
where provided), anchorage ring
Isofix B fig. 132 (one on each side) is
covered with a cloth cap, to be
removed for correctly fastening the
child restraint system.
130F0V0113
131F0V0128
132F0V0330
124
SAFETY