bulb FIAT FULLBACK 2016 1.G User Guide

Front fog lamps*/Daytime running
lamps*
1. Insert a straight blade (or minus)
screwdriver with a cloth over its tip at
the edge of the cover (A) and pry gently
to remove the cover.
2. Remove the 3 screws (B) and
remove the lamp unit.NOTE When unfastening the screws of
the fog lamp, be careful not to
mistakenly move the beam position
adjustment screw (C).
3. Turn the socket anticlockwise to
remove it.
D. Front fog lamp
E. Daytime running lamp4. While holding down the tab, pull out
the bulb.
5. To install the bulb, perform the
removal steps in reverse.
Rear combination lamps
1. Open the rear gate. (Refer to “Rear
gate”).
2. Remove the screws (A) that hold the
lamp unit.
3. Move the lamp unit toward the rear
of the vehicle and remove the clips (B).
A
369AHA102667
B
370AHA102670
C
371AHZ101056
DD
E
E
372AA0112846
A
373AHA102872
218
IN CASE OF EMERGENCY

4. Remove each socket and bulb
assembly by turning it anticlockwise.
C. Tail and stop lamp Remove the bulb
from the socket by turning it
anticlockwise while pressing in.
D. Rear turn-signal lamp Remove the
bulb by pulling it out.
E. Rear fog lamp (driver’s
side)*/Reversing lamp Remove the bulbby pulling it out.
5. To install the bulb, perform the
removal steps in reverse.
When mounting the lamp unit, align the
pins (F) and clip (G) on the lamp unit
with the holes (H) in the body.Licence plate lamps
Type 1
1. Insert a straight blade (or minus)
screwdriver into the lamp assembly and
pry gently to remove it.
NOTE Wrap a piece of cloth around the
tip of the screwdriver in order to avoid
scratching the lens and the body.
2. Remove the socket and bulb
assembly together by turning it
anticlockwise, and then remove the
bulb by pulling out.
B
374AHA102885
E
D
C
375AHA102898
HF
G
376AHA102902377AHA102915
219

3. To install the bulb, perform the
removal steps in reverse.
NOTE When mounting the lamp unit,
put the hook (A) on the right side of the
lamp unit into the body first.Type 2
1. Remove the screws (A) from the
lamp unit, and then remove the lens
and cover.
2. Remove the bulb by pulling out.
3. To install the bulb, perform the
removal steps in reverse.Front room & map lamps*
1. Insert a straight blade (or minus)
screwdriver into the notch of the lens
and pry gently to remove it. Remove the
bulb from the lamp holder.
NOTE Wrap a piece of cloth around the
tip of the screwdriver in order to avoid
scratching the lens.
2. To install the bulb, perform the
removal steps in reverse.
NOTE When installing the lens, align
the 2 tabs on the lens with the holes on
the vehicle side.
378AHA102928
A
379AHZ100639
380AHA104629
381AHA104632
382AHA102931
220
IN CASE OF EMERGENCY

Rear room lamp
Type 1
1. Insert a straight blade (or minus)
screwdriver into the notch of the lens
and pry gently to remove it. Remove the
bulb from the lamp holder.
NOTE Wrap a piece of cloth around the
tip of the screwdriver in order to avoid
scratching the lens.2. To install the bulb, perform the
removal steps in reverse.
NOTE When installing the lens, align
the 2 tabs on the lens with the holes on
the vehicle side.
Type 2
1. Insert a straight blade (or minus)
screwdriver into the notch of the lens
and pry gently to remove it. Remove the
bulb from the lamp holder.Wrap a piece of cloth around the tip of
the screwdriver in order to avoid
scratching the lens.
2. To install the bulb, perform the
removal steps in reverse.
NOTE When installing the lens, fit the
two tabs on one side of the lens into
the holes on the vehicle side before
fitting the two tabs on the opposite side
of the lens into the holes on the vehicle
side.
383AHA102944
384AHA102957
385AHA102960
386AHA104645
221

Glove box lamp
Have the glove box lamp bulb replaced
at a Fiat dealership.
WARNING
299)Bulbs are extremely hot immediately
after being turned off. When replacing a
bulb, wait for it to cool sufficiently before
touching it. You could otherwise be burnt.
300)Handle halogen lamp bulb with care.
The gas inside halogen lamp bulb is highly
pressurized, so dropping, knocking, or
scratching a halogen lamp bulb can cause
it to shatter.
301)Never hold the halogen lamp bulb
with a bare hand, dirty glove, etc. The oil
from your hand could cause the bulb to
break the next time the headlamps are
operated. If the glass surface is dirty, it
must be cleaned with alcohol, paint thinner,
etc., and refit it after drying it thoroughly.302)Always consult a specialist when
repairing or replacing the bulbs of high
intensity discharge headlamps. This is
because the power circuit, bulbs and
electrodes generate a high voltage that
could cause an electric shock.
303)Modifications or repairs to the electric
system that are not carried out properly or
do not take the system technical
specifications into account can cause
malfunctions leading to the risk of fire.
304)Only replace bulbs when the engine is
off. Also ensure that the engine is cold, to
prevent the risk of burns.
387AHZ101043
222
IN CASE OF EMERGENCY

GENERAL
MAINTENANCE
Fuel, engine coolant, oil and
exhaust gas leakage
Look under the body of your vehicle to
check for fuel, engine coolant, oil and
exhaust gas leaks.
Exterior and interior lamp operation
Operate the combination lamp switch
to check that all lamps are functioning
properly. If the lamps do not illuminate,
the probable cause is a blown fuse or
defective lamp bulb. Check the fuses
first. If there is no blown fuses, check
the lamp bulbs. For information
regarding the inspection and
replacement of the fuses and the bulbs,
refer to “Fuses” and “Replacement of
lamp bulbs”. If the fuses and bulbs are
all OK, we recommend you to have
your vehicle checked and repaired.
Meter, gauge and indicator/
warning lamps operation
Start the engine to check the operation
of all instruments, gauges, and indicator
and warning lamps. If there is anything
wrong, we recommend you to have
your vehicle inspected.
Hinges and latches lubrication
Check all latches and hinges, and, if
necessary, have them lubricated.
VEHICLE CARE
PRECAUTIONS
337)
161)
5)
In order to maintain the value of your
vehicle, it is necessary to perform
regular maintenance using the proper
procedures.
Always maintain your vehicle in
compliance with any environmental
pollution control regulations.
Carefully select the materials used for
washing, etc., to be sure that they do
not contain corrosives. If in doubt, we
recommend you to consult a specialist
for the selection of these materials.
WARNING
337)Cleaning products can be dangerous.
Always follow the instructions of the
cleaning product supplier.
IMPORTANT
161)To avoid damage, never use the
following to clean your vehicle: Petrol; Paint
Thinner; Benzine; Kerosene; Turpentine;
Naphtha; Lacquer Thinner; Carbon
Tetrachloride; Nail Polish Remover;
Acetone.
IMPORTANT
5)Detergents pollute the environment. Only
wash your vehicle in areas equipped to
collect and treat wastewater from this type
of activity.
255

Masking the headlamps.........45
Multi information display.........86
Operation under adverse driving
conditions...............204
Outside rearview mirror.........38
Parking..................140
Parking brake...............139
Periodic checks.............240
Power steering fluid...........251
Pretensioners...............106
Read this carefully.............2
Rear Differential lock..........166
Rear gate..................29
Rear seat..................32
Rear view camera............180
Rear window demister switch.....67
Rearview mirrors..............37
Refill capacities..............292
Removal of water from the fuel filter......................188
Replacement of lamp bulbs......213
Safe driving techniques........134
safety systems..............126
SBR system................105
Scheduled Servicing Plan.......225
Seat adjustment..............31
Seat belt reminder............105
Seat belts
Use ...................103
Seats.....................31
Service precautions...........224
Side airbags................122
Sport mode................149
Starting and stopping the engine. . .141
Steering wheel...............35
Steering wheel height and reach
adjustment................35
Steering wheel lock............36
Sun visors..................74
Super Select 4WD II...........162
Supplemental restraint system
airbag..................118Tools, jack and jack handle......189
Towing...................201
Turbocharger operation........145
Turn-signal lever..............43
Tyres ....................260
Tyres and wheels.............291
Use of the Owner Handbook......3
Vanity mirror................75
Vehicle care precautions........255
Vehicle changes/alterations........5
Vehicle dimensions...........271
Vehicle labeling..............266
Vehicle performance..........279
Ventilators..................52
Washer fluid...............249
Weights..................281
Window...................68
Windscreen wiper.............48
Wiper and washer switch........48
Wiper blade rubber replacement . . .254
FCA Italy S.p.A. - MOPAR - Technical Services - Service Engineering
Largo Senatore G. Agnelli, 3 - 10040 Volvera - Turin (Italy)
Print no.
INDEX
Manual transmission..........146
603.99.982 - 04/2016- Edition1