wheel FIAT LINEA RHD 2010 1.G Owner's Manual

113
IMPORTANT Never connect the negative
terminals of the two batteries directly:
sparks could ignite explosive gas released
from the battery. If the auxiliary battery is
installed on another car, prevent
acciden-
tal contact between metallic parts of the
two cars.JUMP STARTING
Never jump start the engine by pushing,
towing or driving downhill.
This could
cause a flow of fuel into the catalytic con-
verter and damage it beyond repair.
IMPORTANT Remember that the brake
booster and the power steering system
are not operating until
the engine is start-
ed, a greater effort will therefore be re-
quired to press the brake pedal or turn
the steering wheel.
REPLACING A WHEEL
GENERAL INSTRUCTIONS
Wheel changing and correct use of the
jack and spare wheel call for some pre-
cautions as listed below.
Indicate that the car is sta-
tionary according to the laws
in force: hazard lights, triangle, etc.
Passengers should leave the car, par-
ticularly if it is very loaded and
wait
for the wheel to be changed away
from on-coming traffic . Apply the
handbrake.
WARNING
CORRECT USE
OF THE CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES WARNING
LIGHTS AND
MESSAGES IN AN
EMERGENCY
CAR
LINEA Owner HAND BOOK RHD.pdf 113LINEA Owner HAND BOOK RHD.pdf 1138/21/09 2:16:16 PM8/21/09 2:16:16 PM

114
The spare wheel is specific
for your car. Do not use it on
cars of different models. Do not use
spare wheels of different models on
your car. The wheel bolts are specif-
ic for your car. Do not use them on
cares of different models. Do not use
bolts of different models on your car.
WARNING
Repair and refit the standard
wheel as soon as possible.
Do not apply grease to the bolt
threading before assembly: the bolts
could come loose unexpectedly.
WARNING
The jack may only be used to
replace wheels on the car
which it equips or other cars of the
same model.
Never use the jack for
other purposes, such as lifting other
car models. Never use the jack to car-
ry out repairs under the car. Incorrect
positioning of the jack may cause the
car to fall. Do not use the jack
for
loads higher than those shown on the
label.
WARNING
Incorrect wheel cup assem-
bly may cause it to come off
when the car is travelling. Never tam-
per with the inflation valve. Never in-
troduce tools of any kind between rim
and tyre. Check tyre and spare wheel
pressure regularly referring to the
val-
ues shown in the “Technical Specifi-
cations” chapter.
WARNING
Important notes:
the jack weighs 1.76 kg;
the jack requires no adjustment;
the jack cannot be repaired: replace
with an original spare part if damaged;
no tool other than its handle may be fit-
ted on the jack.
CORRECT USE
OF THE CAR
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
WARNING
LIGHTS AND
MESSAGES IN AN
EMERGENCY
LINEA Owner HAND BOOK RHD.pdf 114LINEA Owner HAND BOOK RHD.pdf 1148/21/09 2:16:16 PM8/21/09 2:16:16 PM

115
To change a wheel proceed as
follows:
stop the car in a position so that it is
not a danger for on-coming traffic and
where you can replace the wheel safe-
ly. The ground must be flat and com-
pact;
stop the engine off and pull up the hand-
brake;
engage first gear or reverse;
wear the reflecting safety jacket (com-
pulsory by law in certain countries) be-
fore getting out of the car;
open the tailgate and lift the mat;
loosen the fastener A;

take out the tool box Cand take it near
to the wheel to be changed;

take the spare wheel B;
fig. 2F0R0107m
CORRECT USE
OF THE CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES WARNING
LIGHTS AND
MESSAGES IN AN
EMERGENCY
CAR
LINEA Owner HAND BOOK RHD.pdf 115LINEA Owner HAND BOOK RHD.pdf 1158/21/09 2:16:16 PM8/21/09 2:16:16 PM

116
loosen the bolts of the wheel to be re-
placed by about one turn with the
wrench provided E-fig. 3; if the car is
fitted with alloy rims, shake the car to
facilitate removing the rim from the
wheel hub;

operate the device F-fig. 4to extend
the jack until the top of the jack G-fig.
4fits correctly into catch H-fig. 4;
warn anybody nearby that the car is
about to be lifted. They must stay
clear
and not touch the car until it is back on
the ground;
fit the handle L-fig. 4to operate the
jack and lift the car until the wheel to
be changed is several centimetres off
the ground;
fig. 3F0R0108m
fig. 4F0R0155m
CORRECT USE
OF THE CAR
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
WARNING
LIGHTS AND
MESSAGES IN AN
EMERGENCY
LINEA Owner HAND BOOK RHD.pdf 116LINEA Owner HAND BOOK RHD.pdf 1168/21/09 2:16:18 PM8/21/09 2:16:18 PM

117
for versions with wheel cap, remove the
wheel cap after loosening the 3 fastening
bolts and finally loosen the fourth bolt
L-fig. 5and extract the wheel;
make sure the contact surfaces be-
tween spare wheel and hub are clean
so that the fastening bolts will not come
loose;
fit the spare wheel by inserting the first
bolt for two threads into the hole clos-
est to the inflation valve;
fit the wheel cap making the crescent
hole coincide with the bolt you have fit-
ted using the wrench;
tighten the fastening bolts;
turn the jack handle L-fig. 4to lower
the car and remove the jack;

use the wrench provided to fasten the
bolts completely in a criss-cross fashion
as shown in fig. 6;
if replacing a wheel with alloy rim, stove
it temporarily into the spare
wheel
compartment with the cosmetic side
facing upwards.REFITTING THE
STANDARD WHEEL
Following the procedure described previ-
ously, raise the car and remove the
spare
wheel.
fig. 5F0R0156mfig. 6F0R0157m
CORRECT USE
OF THE CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES WARNING
LIGHTS AND
MESSAGES IN AN
EMERGENCY
CAR
LINEA Owner HAND BOOK RHD.pdf 117LINEA Owner HAND BOOK RHD.pdf 1178/21/09 2:16:18 PM8/21/09 2:16:18 PM

118
Versions with steel rims
Proceed as follows:
make sure the contact surfaces be-
tween spare wheel and hub are clean
so
that the fastening bolts will not come
loose;
fit the standard wheel by inserting the
first bolt for two threads into the hole
closest to the inflation valve;
fit the wheel cap making the lunette
hole coincide with the bolt you have fit-
ted then, fit the other 3 bolts;
using the wrench provided, tighten the
fastening bolts;
lower the car and remove the jack;
using the wrench provided, fully tight-
en the bolts in the sequence shown
previously in the figure.Versions with alloy rims
Proceed as follows:
insert the wheel on the hub and using
the wrench provided tighten the bolts;
lower the car and remove the jack;
using the wrench provided, fully tight-
en the bolts in the sequence shown in
the figure.When you have finished
fit the jack partia lly open in its box C-
fig.2 forcing it lightly to prevent it from
vibrating when traelling;
put the tools back into their places
in the container;
stow the container C-fig.2 complete
with tools;
stow the spare wheel in the space pro-
vided in the boot;

tight the fastener A-fig.2;
reposition the mat in the boot.CORRECT USE
OF THE CAR
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
WARNING
LIGHTS AND
MESSAGES IN AN
EMERGENCY
LINEA Owner HAND BOOK RHD.pdf 118LINEA Owner HAND BOOK RHD.pdf 1188/21/09 2:16:19 PM8/21/09 2:16:19 PM

DIPPED BEAM HEADLIGHTS
fig. 10
To change the bulb, proceed as follows:
remove the clipped-on cover;
disconnect the central electric connec-
tor and release the bulb holder catch;
remove the bulb Band replace it;
fit the new bulb, making the outlines of
the metallic part coincide with the
grooves on the reflector;
refit the bulb holder catch and reconnect
the electrical connector;
refit the protection and check that it
is correctly locked.MAIN BEAM HEADLIGHTS
fig. 11
To change the bulb, proceed as follows:
remove the clipped-on cover;
disconnect the central electric connec-
tor and release the bulb holder catch;
remove the bulb Band replace it;
refit the new bulb;
refit the bulb holder catch and reconnect
the electrical connector;
refit the protection and check that it
is correctly locked.DIRECTION INDICATORS
Front fig. 11/a
To change the bulb, proceed as follows:
steer the right/left wheel outwards as
shown in the figure;
turn the catch as shown by the arrow,
then use the lid;
remove the bulb holder cover by turn-
ing it anticlockwise;
fig. 10F0R0222mfig. 11/aF0R0224mfig. 11F0R0223m
122
CORRECT USE
OF THE CAR
AND CONTROLS
DEVICES
MAINTENANCE
SPECIFICATIONS
INDEX
WARNING
LIGHTS AND
MESSAGES IN AN
EMERGENCY
DASHBOARD
SAFETY
CAR
TECHNICAL
LINEA Owner HAND BOOK RHD.pdf 122LINEA Owner HAND BOOK RHD.pdf 1228/21/09 2:16:19 PM8/21/09 2:16:19 PM

LOADS FUSE AMPERES
Cigar lighter or socket
Boot lock actuator
Power window unit (driver’s side front window motor)
Power window unit (passenger’s side front window motor)
+15 control lighting: radio on steering wheel, control panel; power mirrors,
power window unit, alarm setup
+15 airbag node
+15 radio setup, Blu&Me setup
Power window unit, driver’s seat adjustment motor
Body computer and instrument panel node F44
F45
F47
F48
F49
F50
F51
F52
F5315
10
20
20
7.5
7.5
7.5
15
7.5
132
CORRECT USE
OF THE CAR
AND CONTROLS
DEVICES
MAINTENANCE
SPECIFICATIONS
INDEX
WARNING
LIGHTS AND
MESSAGES IN AN
EMERGENCY
DASHBOARD
SAFETY
CAR
TECHNICAL
LINEA Owner HAND BOOK RHD.pdf 132LINEA Owner HAND BOOK RHD.pdf 1328/21/09 2:16:21 PM8/21/09 2:16:21 PM

FASTENING THE TOW
RING fig. 33
Proceed as follows:

release the cap A;
take the tow hook Bfrom the sup-
port;
tighten the ring on the rear or front
threaded pin.
The power brakes and pow-
er steering will not work while
the car is being towed. More effort on
the
brake pedal and steering wheel will
therefore be required. Do not use wires
for towing. Do not jerk. Make sure not
to damage parts in contact with the
car while towing. Respect the specific
rules of the Highway Code when tow-
ing the car specifically in relation to
the towing device and the behaviour
to maintain on the road.
WARNING
fig. 33F0R0131m
Do not start the engine while
towing the car.
WARNING
Clean the threaded seat
carefully before fastening
the ring . Make sure that the ring is
fully fastened in the seat before tow-
ing the car.
WARNING
Release the steering wheel
lock before towing (see “Ig-
nition device” in “Dashboard and con-
trols”). The power brakes and power
steering will not work while the car is
being towed. More effort on the brake
pedal and steering wheel will therefore
be required. Do not use wires for tow-
ing. Do not jerk. Make sure not to
damage parts in contact with the car
while towing. Respect the specific rules
of the Highway Code when towing the
car specifically in relation to the tow-
ing device and the behaviour to main-
tain on the road.
WARNING
136
CORRECT USE
OF THE CAR
AND CONTROLS
DEVICES
MAINTENANCE
SPECIFICATIONS
INDEX
WARNING
LIGHTS AND
MESSAGES IN AN
EMERGENCY
DASHBOARD
SAFETY
CAR
TECHNICAL
LINEA Owner HAND BOOK RHD.pdf 136LINEA Owner HAND BOOK RHD.pdf 1368/21/09 2:16:21 PM8/21/09 2:16:21 PM

SCHEDULED SERVICING ................................................ 138
SERVICE SCHEDULE
PETROL VERSIONS ............................................................. 139
REGULAR INSPECTIONS ................................................. 143
DEMANDING USE OF THE CAR ................................... 143
CHECKING FLUID LEVELS................................................ 144
AIR CLEANER ...................................................................... 149
POLLEN FILTER ................................................................... 149
BATTERY ................................................................................ 149
WHEELS AND TYRES ......................................................... 152
RUBBER HOSES .................................................................... 153
WINDSCREEN WIPERS ...................................................... 153
BODYWORK ........................................................................ 155
INTERIORS ............................................................................ 157
CC C
A A
R R
M M
A A
I I
N N
T T
E E
N N
A A
N N
C C
E E
137
CAR
MAINTENANCE
CORRECT USE
OF THE CAR
TECHNICAL
INDEX
DASHBOARD
SAFETY
WARNING
LIGHTS AND
MESSAGES IN AN
EMERGENCY
SPECIFICATIONS
AND CONTROLS
DEVICESSERVICE SCHEDULE
VERSIONS ............................................................ 1 DIESEL . 41
LINEA Owner HAND BOOK RHD.pdf 137LINEA Owner HAND BOOK RHD.pdf 1378/21/09 2:16:21 PM8/21/09 2:16:21 PM