light FIAT PANDA 2007 169 / 2.G 4x4 Supplement Manual
[x] Cancel search | Manufacturer: FIAT, Model Year: 2007, Model line: PANDA, Model: FIAT PANDA 2007 169 / 2.GPages: 26, PDF Size: 1.13 MB
Page 2 of 26
1
FIAT PANDA 4 x 4
This Supplement describes the main fea-
tures of Fiat Panda 4 x 4 versions togeth-
er with a few instructions for use. For all
the other information not contained here-
in, refer to the Owner Handbook this sup-
plement is attached to.
FIAT PANDA 4 x 4 DRIVE LINE
Fiat Panda 4 x 4 drive line features
two differentials and a viscous joint.
Thanks to this system, under poor
grip conditions the four-wheel drive
will engage automatically (i.e.: no
driver’s action required) and provide
optimum torque distribution be-
tween front and rear axle.
Fiat Panda 4 x 4 is therefore suited
for all types of roads: in fact, it is ca-
pable of coping well with snowy, icy,
muddy and dirt roads, even with
steep slopes.SUMMARY
ABS SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
ELD - ELECTRONIC LOCKING DIFFERENTIAL . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
HEADLIGHT WASHER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
IF A TYRE IS PUNCTURED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
IF AN EXTERIOR LIGHT BURNS OUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
WASHING THE CAR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
TOWING THE CAR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
TOWING TRAILERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
SERVICE SCHEDULE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
ENGINE CODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
BODY VERSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
WHEELS AND TYRES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
INFLATING PRESSURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
SNOW CHAINS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
TRANSMISSION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
STEERING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
PERFORMANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
CAPACITIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
WEIGHTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
FUEL CONSUMPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
CO
2EMISSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
603.83.460 PANDA 4X4 GB 26-06-2007 11:19 Pagina 1
Page 4 of 26
3
FIAT PANDA 4 x 4
ELD operation
At start-up the ELD system is off.
To turn the ELD system on, press button
fig. 1; the relevant button led will turn on.
The system cuts in at a speed below 30
km/h as described previously: in this event
the instrument panel warning light fig. 2
will flash.ELD warning light indications, fig. 2
The ELD warning light indicates the fol-
lowing two system conditions:
❒flashing: system active;
❒glowing steadily: system failure, in
this event contact Fiat Dealership as
soon as possible.
HEADLIGHT WASHER
(where provided)
The headlight washing system consists of
two nozzles for washing the external
headlight lens. This function can be acti-
vated using the windscreen washer stalk
only if dipped beams or main beams are
on. Operating the stalk to wash the wind-
screen will automatically start the head-
light washer.
This version features a windscreen wash-
er fluid reservoir with improved capaci-
ty, i.e.: 4.5 litres.
fig. 1F0G0605mfig. 2F0G0606m
603.83.460 PANDA 4X4 GB 26-06-2007 11:19 Pagina 3
Page 8 of 26
7
FIAT PANDA 4 x 4
IF AN EXTERIOR LIGHT
BURNS OUT
(Fiat Panda 4 x 4 CROSS
version)
IMPORTANT To change an external light
on Fiat Panda 4 x 4 and Fiat Panda 4 x 4
Climbing versions, refer to the Owner
Handbook this Supplement is attached to.
For the type of bulb and power rating re-
fer to paragraph “When needing to change
a bulb” in section “In an emergency” in the
attached Owner Handbook.
FRONT LIGHT UNITS
To change the dipped beam bulb, proceed
as follows:
❒remove the cover A-fig. 11;
❒disconnect the connector C-fig. 12;
❒release the bulb holder catch A;
❒remove the bulb Band fit the new bulb.To change the front sidelight bulb, pro-
ceed as follows:
❒remove the cover A-fig. 11;
❒remove the bulb holder A-fig. 12
❒remove the bulb B;
❒fit the new bulb.To change the front fog light bulb, proceed
as follows:
❒remove the cover A-fig. 11;
❒disconnect the connector D-fig. 14;
❒turn slightly the bulb holder B and re-
move it;
❒remove the bulb C and fit the new bulb.
To change the main beam bulb, proceed
as follows:
fig. 11F0G0617m
fig. 12F0G0618m
fig. 13F0G0619m
fig. 14F0G0628m
603.83.460 PANDA 4X4 GB 26-06-2007 11:19 Pagina 7
Page 9 of 26
8
FIAT PANDA 4 x 4
❒loosen the three fastening screws A-
fig. 15and remove the headlight cov-
er;
❒remove the cover by removing the
catches B;
❒remove the lens fig. 16by loosening
the three fastening screws A;
❒turn connector A-fig. 17counter-
clockwise and remove it;
❒remove the bulb B-fig. 17and fit the
new bulb.
To change the direction indicator bulb,
proceed as follows:
❒loosen the two fastening screws A-
fig. 18and remove the cover B;
❒loosen the fastening screws A-fig. 19
and remove the lens B;
❒remove the cap A-fig. 20from the lens
Band remove the bulb holder C;
❒remove bulb Dby pushing it slightly and
turning it counter-clockwise, then fit
the new bulb.
To change side direction indicators, third
brake light and number plate light bulbs re-
fer to paragraph “When needing to change
a bulb” in section “In an emergency” in the
attached Owner Handbook.
fig. 15F0G0620mfig. 17F0G0622m
fig. 16F0G0621mfig. 18F0G0623m
fig. 19F0G0624m
fig. 20F0G0631m
603.83.460 PANDA 4X4 GB 26-06-2007 11:19 Pagina 8
Page 10 of 26
9
FIAT PANDA 4 x 4
REAR LIGHT UNITS
The bulbs are arranged inside the light unit
as follows fig. 21:
A12V-W5W, double filament bulb for
brake lights/taillights.
B12V-P21W bulb for direction indica-
tors.
C12V-P21W bulb for rear fog light (left
headlight) or reversing light (right head-
light).To change a bulb proceed as follows:
❒loosen the three screws A-fig. 22then
pull gently the headlight outwards un-
til releasing it from the three catches;
fig. 22F0G0625mfig. 23F0G0626m
❒loosen the four screws A-fig. 23and
disconnect the two connectors;
❒remove the required bulb holder turn-
ing it counter-clockwise;
❒remove the required bulb (A, Bor C-
fig. 21), pushing it slightly and turning
it counter-clockwise (bayonet cou-
pling), then fit the new bulb.
fig. 21F0G0627m
603.83.460 PANDA 4X4 GB 26-06-2007 11:19 Pagina 9
Page 13 of 26
12
FIAT PANDA 4 x 4
20 40 60 80 100 120 140 160 180
●●●●● ●●●●
●●●●● ●●●●
●●●●● ●●●●
●●●●● ●●●●
●●●●● ●●●●
●● ● ●
●●●●● ●●●●
●●●●● ●●●●
●
●● ● ●
●● ● ●
●● ● ●
●●
SERVICE SCHEDULE
Thousands of km
Check tyre conditions/wear and adjust pressure
if required
Check light system operation (headlights, direction indicators,
hazard lights, passenger compartment lights, boot lights,
warning lights, etc.)
Check windscreen wiper/washer operation,
adjust nozzles
Check windscreen/rear window blade
position/wear
Check front disk brake pad conditions and wear
Check rear disk brake pad conditions and wear
Sight inspect the conditions of: body external parts,
underbody protection, pipes and hoses
(exhaust - fuel - brakes), rubber parts
(boots, sleeves, bushes, etc.)
Check cleanness of locks, bonnet and boot and lever cleanness
and lubrication
Check tension and adjust accessory drive belts
(excluding engines with automatic belt tighteners)
Sight inspect accessory drive belt conditions
Check and adjust tappet clearance (petrol versions)
Check handbrake lever stroke
Check antievaporation system (petrol versions)
603.83.460 PANDA 4X4 GB 26-06-2007 11:19 Pagina 12
Page 21 of 26
20
FIAT PANDA 4 x 4
1.2
30
4.5
–
–
4.6
2.5
2.8
–
–
2.7
0.9
0.55
4.51.3 Multijet
–
–
30
4.5
6.5
–
–
2.85
3.0
2.7
0.9
0.55
4.5Specified fuels
and recommended products
Unleaded premium petrol with no
less than 95 R.O.N
(EN 228 Specification)
Diesel fuel for motor vehicles
(EN 590 Specification)
Mixture of 50% water and 50%
PARAFLU UP
SELENIA 20K(*)
SELENIA WR
TUTELA CAR TECHNYX (**)
TUTELA W90/M-DA(***)
TUTELA TOP 4
Mixture of water and
TUTELA PROFESSIONAL SC 35
CAPACITIES
Fuel tank: litres
including a reserve of: litres
Fuel tank: litresincluding a reserve of: litres
Engine cooling system: litres
Engine sump: litres
Engine sump and filter: litres
Engine sump: litres
Engine sump and filter: litres
Gearbox/differential: litres
Rear differential: litres
Hydraulic brake circuit: kg
Windscreen/rear window and
headlight washer fluid reservoir litres
(*) For use in particularly harsh weather conditions SELENIA PERFORMER MULTIPOWERengine oil is recommended
(**) SAE 75W-85synthetic oil that passes API GL4 PLUS, MIL - L - 2105 D Lev specifications
(***) SAE 80W-90mineral oil that passes API GL5, MIL - L - 2105 D Lev specifications
603.83.460 PANDA 4X4 GB 26-06-2007 11:19 Pagina 20