fig 49 FIAT PANDA 2007 169 / 2.G Repair Manual

76
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SOUND SYSTEM PRESETTING
(where provided)
In addition to what provided with the stan-
dard set-up, the car is also fitted with:
❒two full range speakers, 165 mm diam-
eter, 40 W power each on front doors;
❒two full range speakers, 130 mm diam-
eter, 35 W power each on rear doors;
❒aerial power wire;
❒front and rear speaker power wires;
❒sound system power wires;
❒aerial on the car roof.SOUND SYSTEM
(where provided)
The complete system consists of the fol-
lowing:
❒two full range speakers, 165 mm diam-
eter, 40 W power each on front doors;
❒two full range speakers, 130 mm diam-
eter, 35 W power each on rear doors;
❒aerial on car roof;
❒radio with tape-recorder or sound sys-
tem with CD player or sound system
with MP3 CD player (for its operation
and characteristics see the “Sound sys-
tem” supplement attached to the pre-
sent Handbook).
With HiFi system (if required):
❒two tweeters A-fig. 97and two
woofers B, 40 W max power each on
front doors;
❒two full range speakers, 40 W max
power each on rear doors;
❒a subwoofer, 100 W power, under the
right seat;
❒aerial on the roof;
❒sound system with CD player or sound
system with MP3 CD player (for its op-
eration and characteristics see the
“Sound system” supplement attached
to the present Handbook). If after buying the car, you
decide to install a sound sys-
tem, contact Fiat Dealership
whose qualified personnel will
help you choose a sound system that
does not damage the battery charge.
Excessive electrical absorption dam-
ages the battery and makes its war-
ranty no longer valid.
fig. 96F0G0071m
SOUND SYSTEM
When the sound system has not been re-
quested the car is provided with two odd-
ment compartments on the instrument
panel.
STANDARD SOUND SYSTEM
fig. 96
The system consists of:
❒sound system power wires;
❒oddment compartment;
❒front and rear speaker compartments.
Remove the door panel to fit the speak-
ers.
Have this operation carried out at a Fiat
Dealership.
The sound system is to be fitted in the
dedicated seat in the oddment compart-
ment which can be removed by pressing
the two retaining tabs A.
Here you can find power wires.
060-080 Panda New GB 21-06-2007 13:48 Pagina 76

77
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
INSTALLATION OF ELECTRIC/
ELECTRONIC DEVICES
Electric/electronic devices installed after
buying the vehicle or in aftermarket shall
bear the and marking:
Fiat Auto S.p.A. authorizes the installation
of transceivers provided that installation
is carried out at a specialized shop, work-
manlike performed and in compliance with
manufacturer's specifications.
IMPORTANT Installation of devices re-
sulting in modifications of vehicle charac-
teristics may cause driving license seizing
by traffic agents and also the lapse of the
warranty as concerns defects due to the
abovementioned modification or traceable
back to it directly or indirectly.
Fiat Auto S.p.A. declines all responsibility
for damages caused by the installation of
non-genuine accessories or not recom-
mended by Fiat Auto S.p.A. and installed
not in compliance with the specified re-
quirements.RADIO TRANSMITTERS
AND CELLULAR TELEPHONES
Radio transceiver equipment (e.g.: HAM
radio systems and the like) shall not be
used inside the vehicle unless a separate
aerial is mounted on the roof.
IMPORTANT The use of similar devices
inside the passenger compartment (with-
out separated aerial) produces radio-fre-
quency electromagnetic fields which, am-
plified by the resonance effects inside the
passenger compartment, may cause elec-
trical systems equipping the vehicle to mal-
function. This could compromise safety in
addition to constituting a potential hazard
for the passengers.
In addition, transmission and reception of
these devices may be affected by the
shielding effect of the vehicle body.
As concerns EC-approved mobile phones
(GSM, GPRS, UMTS), strictly comply with
the instructions for use provided by the
mobile phone’s manufacturer. ACCESSORIES PURCHASED
BY THE OWNER
If after buying the car, you decide to install
electrical accessories that require a per-
manent electric supply (alarm, satellite an-
titheft system, etc.) or accessories that in
any case burden the electric supply, con-
tact Fiat Dealership, whose qualified per-
sonnel, besides suggesting the most suit-
able devices belonging to Lineaccessori Fi-
at, will also evaluate the overall electric ab-
sorption, checking whether the car’s elec-
tric system is able to withstand the load
required, or whether it needs to be inte-
grated with a more powerful battery.
fig. 97F0G0073m
060-080 Panda New GB 21-06-2007 13:48 Pagina 77

78
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
DIESEL ENGINES
Operation at low temperatures
If the outside temperature is very low, the
diesel thickens due to the formation of
paraffin and could cause the malfunction-
ing of the fuel system.
In order to avoid these problems, differ-
ent types of diesel are distributed ac-
cording to the season: summer type, win-
ter type and arctic type (cold, mountain
areas). If refuelling with diesel fuel not suit-
able for the current temperature, mix
diesel fuel with TUTELA DIESEL ART ad-
ditive in the proportions stated on the can,
putting first the antifreeze in the tank and
then the diesel fuel.
If driving or parking the vehicle for a long
period in cold areas/mountains, refuel with
the diesel fuel available at local filling sta-
tions.
In this situation you are also recom-
mended to have in the tank an amount of
fuel 50% higher than usable capacity.AT THE FILLING
STATION
PETROL ENGINES
Use only unleaded petrol.
To prevent errors, the diameter of the fu-
el tank filler is too small to introduce a lead
petrol pump filler.
Use petrol with a rated octane number
(R.O.N.) not lower than 95.
IMPORTANT An inefficient catalyst leads
to harmful exhaust emissions, thus con-
tributing to air pollution.
IMPORTANT Never use leaded petrol,
even in small amount or in an emergency,
as this would damage the catalyst beyond
repair.
fig. 98F0G0041m
The car must only be filled
with diesel fuel for motor ve-
hicles, in compliance with Eu-
ropean Standard EN590. The
use of other products or mixtures may
irreparably damage the engine with in-
validation of the warranty due to the
damage caused. In the event of acci-
dentally filling with another type of fu-
el, do not start the engine and empty
the tank. If the engine has been run
even for only a very short time, in ad-
dition to the tank, it is also necessary
to drain out the whole fuel circuit.
REFUELLING
To guarantee full tank filling, carry out two
refuelling operations after the first click of
the fuel delivery gun. Avoid further top-
ping up operations that could cause dam-
ages to the fuel system.
060-080 Panda New GB 21-06-2007 13:48 Pagina 78

79
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
PROTECTING THE
ENVIRONMENT
The devices for curtailing petrol engine
emissions are the following:
❒ three-way catalytic converter;
❒Lambda sensor;
❒fuel evaporation system.
In addition, do not let the engine run, even
for a test, with one or more spark plugs
disconnected.
The devices for curtailing diesel fuel en-
gine emissions are the following:
❒oxidising catalytic converter;
❒ exhaust gas recirculation system
(E.G.R.);
❒ diesel particulate filter (DPF). FUEL FILLER CAP fig. 98 and 99
The fuel filler cap Bis fitted with an anti-
loss device Cwhich fastens it to the flap
Aso it cannot be mislaid.
To slacken the cap Bfirst open the flap A.
The sealing of the tank may cause light
pressurising in the tank. A little breathing
off, while slackening the cap is absolutely
normal.
When refuelling, position the cap on the
device inside the flap as shown in the fig-
ure.
fig. 99F0G0042m
Do not put naked flames or
lighted cigarettes near the fu-
el filler hole as there is a dan-
ger of fire. Do not bend too
close to the hole either so as not to
breathe in harmful vapours.
During normal service the
catalyst reaches high tem-
peratures. Do not therefore park the
car over inflammable materials (grass,
dry leaves, pine needles, etc.): fire
hazard.
WARNING
060-080 Panda New GB 21-06-2007 13:48 Pagina 79

82
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
IINDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
When the car is parked on a steep slope
the reel mechanism may block; this is nor-
mal. The reel mechanism prevents the
webbing coming out when it is jerked or
if the car brakes sharply, in a collision or
when cornering at high speeds.
The rear seat is fitted with inertial seat
belts with three anchor points and reel.
As an optional, (only for homologated 5-
seat cars) also the centre seat can be fit-
ted with three anchor points and reel or
with lap belt with two anchor points for
versions/markets where applicable.
IMPORTANT Remember that in the
event of a violent collision, back seat pas-
sengers not wearing seat belts also rep-
resent a serious danger for front seat pas-
sengers.SEAT BELT HEIGHT
ADJUSTMENT (where provided)
Four different adjustments in height are
provided.
To adjust, press button A-fig. 2and low-
er or raise the grip B.
Always adjust the height of the seat belt
to fit the person wearing it: this precau-
tion could greatly reduce the risk of injury
in case of collision.
Correct adjustment is obtained when the
belt passes half way between the end of
the shoulder and the neck.
See texts and figures given in paragraph
“General instructions for using the seat
belts” in this section.
SEAT BELTS
USING THE SEAT BELTS fig. 1
The belt should be worn keeping the chest
straight and rested against the seat back.
To fasten the seat belts, take hold the
tongue Aand insert it into the buckle B,
until hearing the locking click. At removal,
if it jams, let it rewind for a short stretch,
then pull it out again without jerking.
To unfasten the seat belts, press button
C. Guide the seat belt with your hand
while it is rewinding, to prevent it from
twisting. Through the reel, the belt auto-
matically adapts to the body of the pas-
senger wearing it, allowing freedom of
movement.
fig. 1F0G0053mfig. 2F0G0054m
Never press button C when
travelling.
WARNING
081-100 Panda New GB 21-06-2007 13:49 Pagina 82

83
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
For certain versions, the front seat belts
have just one fixed anchoring point C-
fig. 3on the door post.USING THE CENTRAL SEAT
BELT
Static lap belt with 2 anchor points
(for versions/markets where
applicable) fig. 4
To fasten the seat belt: fit the tongue A
into the buckle Buntil hearing the locking
click.
To unfasten the seat belt: press button C.
To adjust the belt: run the tape in the
buckle D, pulling the end E) to tighten and
section Fto loosen.
fig. 3F0G0195mfig. 4F0G0224m
Make height adjustment
when the car is stationary.
WARNING
After adjustment, always
check that the slider is an-
chored in one of the positions pro-
vided. To do this, with the button A
released, exert a further pressure to
allow the anchor device to catch if re-
lease did not take place at one of the
preset positions.
WARNING
081-100 Panda New GB 21-06-2007 13:49 Pagina 83

84
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
IINDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
Boot extension: unfasten the belt through
button Mand guide the belt to prevent
it from twisting; overlap tongues Iand G,
on the catch Hin the reel compartment.
IMPORTANT After repositioning the
seats, restore proper seat belts conditions
for prompt use.PRETENSIONERS
To increase the efficiency of the front and
rear (where provided) seat belts, the Fiat
Panda is fitted with pretensioners. These
devices “feel”, through a sensor, that a vi-
olent crash is in progress and rewind the
seat belts a few centimetres. In this way
they ensure that the seat belt adheres per-
fectly to the wearer before the restrain-
ing action begins.
The seat belt locks to indicate that the de-
vice has intervened; the seat belt cannot
be drawn back up even when guiding it
manually.
IMPORTANT To obtain the highest de-
gree of protection from the action of the
pretensioning device, wear the seat belt
keeping it firmly close to the chest and
pelvis.
A small amount of smoke may be pro-
duced. This smoke is in no way toxic and
presents no fire hazard.
The pretensioner does not require any
maintenance or greasing. Anything that
modifies its original conditions invalidates
its efficiency. If due to unusual natural
events (floods, sea storms, etc.) the device
has been affected by water and mud, it
must necessarily be replaced. Seat belt with three anchor points
(for versions/markets where
applicable) fig. 5
The seat belt has two webbings and a dou-
ble buckle.
To use the seat belts, take the tongues out
of the reel compartment and pull the belt,
guide the belt to prevent it from twisting
then secure tongue Ginto buckle Lfitted
with the black button M.
To fasten the belt, run the belt and secure
tongue Iinto the corresponding buckle N.
To fasten the belt: press button Oand guide
the belt to prevent it from twisting.
fig. 5F0G0241m
Remember that in the case
of a violent collision, back
seat passengers not wearing seat belts
also represent a serious danger to the
passengers in the front.
WARNING
081-100 Panda New GB 21-06-2007 13:49 Pagina 84

85
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
LOAD LIMITERS
To increase passenger’s safety, the front
and rear (where provided) seat belt reels
contain a load limiter which allows con-
trolled sag in such a way as to dose the
force acting on the shoulders during the
belt restraining action in case of front
crash.
GENERAL INSTRUCTIONS FOR
USING THE SEAT BELTS
The driver must comply with (and have
the car occupants follow) all the local law
regulations concerning the use of seat
belts. Always fasten the seat belts before
starting.
Seat belts are also to be worn by expec-
tant mothers: the risk of injury in the case
of accident is greatly reduced for them and
the unborn child if they are wearing a seat
belt. Of course they must position the
lower part of the belt very low down so
that it passes under the abdomen (as il-
lustrated in fig. 6).
fig. 6F0G0046m
The pretensioner can only
be used once. After a colli-
sion that has triggered it, have it re-
placed at a Fiat Dealership. Preten-
sioner validity is written on the label
set on the door contour sheet metal.
Pretensioners should be replaced at
Fiat Dealership as this date ap-
proaches.
WARNING
Operations which lead to
knocks, vibrations or localised
heating (over 100°C for a
maximum of 6 hours) in the
area around the pretensioners may
cause damage or trigger them. These
devices are not affected by vibrations
caused by irregularities of the road sur-
face or low obstacles such as kerbs, etc.
Contact a Fiat Dealership for any as-
sistance.For maximum safety, keep
the back of your seat up-
right, lean back into it and make sure
the seat belt fits closely across your
chest and hips. Make sure that the
seat belts of the front and rear pas-
sengers are fastened at all times! You
increase the risk of serious injury or
death in a collision if you travel with
the belts unfastened.
WARNING
Under no circumstances
should the components of
the seat belts and pretensioners be
tampered with or removed. Any op-
eration should be carried out by qual-
ified and authorised personnel. Al-
ways contact a Fiat Dealership.
WARNING
081-100 Panda New GB 21-06-2007 13:49 Pagina 85

86
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
IINDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
IMPORTANT Each belt shall be used by
one person only: never travel with a child
sitting on the passenger’s lap with a sin-
gle belt to protect them both fig. 8. Do
not fasten other objects to the body.HOW TO KEEP THE SEAT
BELTS ALWAYS IN EFFICIENT
CONDITIONS
Observe the following:
❒always use the belt with the tap taut and
never twisted; make sure that it is free
to run without impediments;
❒after a serious accident, replace the belt
being worn at that time, even if it does
not appear damaged. Always replace
the seat belt if pretensioners have been
activated;
❒to clean the belts, wash by hand with
neutral soap, rinse and leave to dry in
the shade. Never use strong deter-
gents, bleach or dyes or other chemi-
cal substance that might weaken the fi-
bres;
❒prevent the reels from getting wet:
their correct operation is only guaran-
teed if water does not get inside;
❒replace the seat belt when showing sig-
nificant wear or cut signs. IMPORTANT The belt should not be
twisted. The upper part should pass over
the shoulder and cross the chest diago-
nally. The lower part should adhere to the
pelvis (as illustrated in fig. 7) and not to
the abdomen of the passenger. Do not use
any objects (pegs, stoppers, etc.) to keep
the belts away from the body.
fig. 7F0G0044mfig. 8F0G0045m
If the belt has been subject-
ed to heavy stress, for ex-
ample after and accident, it should be
changed completely together with
the anchors, anchor fastening screws
and the pretensioners. In fact, even if
the belt has no visible defects, it could
have lost its resilience.
WARNING
081-100 Panda New GB 21-06-2007 13:49 Pagina 86

88
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
IINDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
GROUP 2
Starting from 15 to 25 kg in weight, chil-
dren may be restrained directly by the car
belts fig 11.
The only function of the seat is to position
the child correctly in relation to the belts,
so that the diagonal part adheres to the
chest and not to the neck and that the
horizontal part clings to the child’s pelvis
and not the abdomen.
fig. 11F0G0049m
GROUP 1
Starting from 9 to 18 kg in weight, children
may be carried facing forwards, with seats
fitted with front cushion, through which
the car seat belt restrains both child and
seat fig. 10. GROUP 0 and 0+
Babies up to 13 kg must be carried facing
backwards on a cradle seat which, sup-
porting the head, does not induce stress
on the neck in the event of sharp decel-
eration.
The cradle is restrained by the car seat
belts, as shown in fig. 9and in turn it must
restrain the child with its own belts.
fig. 9F0G0047mfig. 10F0G0048m
The figure is only an example for mounting. Attain to the instructions
for fastening which must be enclosed with the specific child restrain-
ing system you are using.
WARNING
Seats exist which are suitable for covering weight groups 0 and 1 with a
rear connection to the car belts and their own belts to restrain the child.
Due to their size, they can be dangerous if installed incorrectly fastened to the car
belts with a cushion. Carefully follow the instructions for installation provided with
the seat.
WARNING
The figure is only an exam-
ple for mounting. Attain to
the instructions for fastening which
must be enclosed with the specific
child restraining system you are using.
WARNING
081-100 Panda New GB 21-06-2007 13:49 Pagina 88