reset key FIAT PANDA 2007 169 / 2.G Owners Manual

18
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
fig. 20F0G0015m
DIGITAL DISPLAY
“STANDARD” SCREEN fig. 20
The standard screen shows the following
indications:
AHeadlight aiming position (only with
dipped beam headlights on).
BClock (always displayed, even with ig-
nition key removed and front doors
closed).
COdometer (covered km or miles).CONTROL BUTTONS fig. 21
APress briefly for switching from total
to partial km/miles.
Long press (over 2 seconds) to reset
partial km/miles.
BSet clock.
SETTING THE CLOCK fig. 21
To set the clock hour press button B.
Every press on the button increases or de-
creases by one unit. Keeping the corre-
sponding button pressed obtains auto-
matic fast increase or decrease. When you
are near the required value, release the
button and complete adjustment with sin-
gle presses.
fig. 21F0G027m
NoteWith key removed (when opening
one of the front doors) the display will
turn on and show for a few seconds the
km or mi covered.
001-031 Panda New GB 21-06-2007 13:47 Pagina 18

28
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
NoteThe “Service Schedule includes car
maintenance every 20,000 km (or 12,000
mi); this is shown automatically, with the
ignition key at MAR, starting from 2,000
km (or the equivalent value in miles) from
this deadline and it is shown again every
200 km (or the equivalent value in miles).
Below 200 km servicing indications are
displayed more frequently. Service indica-
tions will be displayed km or mi according
to previous unit setting. When a pro-
grammed maintenance interval (coupon)
is near to come, turning the ignition key
to MAR, the display will show the mes-
sage “Service” followed by the number of
km/mi to go before car servicing. Contact
a Fiat Dealership to carry out any service
operation provided by the “Service sched-
ule” and to reset the display.Exit Menu
This is the last function that closes the cir-
cular setting cycle listed in the initial menu
screen.
Briefly press button MODEto go back to
the standard screen without storing set-
tings.
Press button –to return to the first menu
option (Speed Lim.). Scheduled Servicing (Service)
Through this function it is possible to dis-
play information connected to proper car
servicing.
Proceed as follows:
– briefly press button MODE: service in
km or mi, according to previous setting,
will be displayed (see paragraph “Units”);
– briefly press button MODEto go back
to the menu screen or press the button
for long to go back to the standard screen.
001-031 Panda New GB 21-06-2007 13:47 Pagina 28

29
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
TRIP COMPUTER
(where provided)
General features
The “Trip computer” is provided on cars
fitted with multifunction display or re-
configurable multifunction display. The
“Trip computer” displays information
(with ignition key at MAR) relating to the
operating status of the car. This function
comprises the “General trip” concerning
the “complete mission” of the car (jour-
ney) and “Trip B”, (only available on re-
configurable multifunction display), con-
cerning the partial mission of the car; this
latter function (as shown in fig. 31) is “con-
tained” within the complete mission.Both functions are resettable (reset - start
of new mission).
“General Trip” displays the figures relat-
ing to:
– Range to empty (where provided)
– Trip distance
– Average consumption (where provided)
– Instant consumption (where provided)
– Average speed
– Trip time (driving time).“Trip B” (only available on reconfigurable
multifunction display), displays the figures
relating to:
– Trip distance B
– Average consumption B (where provided)
– Average speed B
– Trip time B (driving time).
NoteThe “Trip B” function can be ex-
cluded (see paragraph “Trip B On/Off”).
“Range to empty” cannot be reset.
001-031 Panda New GB 21-06-2007 13:47 Pagina 29

30
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
Average speed
This value shows the car average speed as
a function of the overall time elapsed since
the start of the new mission.
Trip time
This value shows the time elapsed since
the start of the new mission.
IMPORTANT Lacking information, Trip
computer values are displayed with “----”.
When normal operating condition is re-
set, calculation of different units will
restart regularly. Values displayed before
the failure will not be reset.TRIP button fig. 30
Button TRIP, set on the top of the right
steering column stalk, shall be used (with
ignition key at MAR) to display and to re-
set the previously described values to start
a new mission:
– short push to display the different val-
ues
– long push to reset and then start a new
mission.
New mission
New mission starts after:
– “manual” resetting by the user, by press-
ing the relevant button;
– “automatic” resetting, when the “Trip dis-
tance” reaches 3999.9 km or 9999.9 km
(according to the type of display) or when
the “Trip time” reaches 99.59 (99 hours
and 59 minutes);
– after disconnecting/reconnecting the
battery. Values displayed
Range to empty (where provided)
This value shows the distance in km (or
mi) that the car can still cover before
needing fuel, assuming that driving condi-
tions are kept unvaried. The display will
show “----” in the following cases:
– value lower than 50 km (or 30 mi)
– car left parked with engine running for
long.
Trip distance
This value shows the distance covered
from the start of the new mission.
Average consumption (where provided)
This value shows the average consump-
tion from the start of the new mission.
Instant consumption (where provided)
This value shows instant fuel consumption
(this value is updated second by second).
If parking the car with engine on,
the display will show “----”.
001-031 Panda New GB 21-06-2007 13:47 Pagina 30

31
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
Start of journey procedure
With ignition key at MAR, press and keep
button TRIPpressed for over 2 seconds
to reset.
Exit Trip
To quit the Trip function: keep button
MODEpressed for over 2 seconds. IMPORTANT The reset operation in the
presence of the screens concerning the
“General Trip” makes it possible to reset
also the “Trip B”. The reset operation in
the presence of the screens concerning
only the “Trip B” makes it possible to re-
set only the information associated with
this function.
TRIP
F0G0149mfig. 30
Reset TRIP B
End of partial mission
Start of new partial mission
End of partial mission
Start of new
partial mission
Reset TRIP B
End of partial mission
Start of new
partial mission Reset GENERAL TRIP
End of complete mission
Start of new missionReset GENERAL TRIP
End of complete mission
Start of new mission
End of partial mission
Start of new
partial mission Reset TRIP B
Reset TRIP B
TRIP B
TRIP B
TRIP B GENERAL TRIP˙
˙
˙
˙˙
˙
˙ ˙
fig. 31
001-031 Panda New GB 21-06-2007 13:47 Pagina 31

53
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IIN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
INTERIOR FITTINGS
CIGAR LIGHTER AND ASHTRAY
(where provided) fig. 57
Press button A; after approximately 15
seconds the cigar lighter will return to its
initial position and is ready for use.
IMPORTANT Always check that the cig-
ar lighter has turned off.
SUN VISORS fig. 58
They are located at the sides of the dri-
ving mirror.
They can be adjusted forwards and side-
wards.
A courtesy mirror is applied to the back
of the passenger’s side sun visor, while a
pocket is applied to the back of the dri-
ver’s side sun visor. On certain versions
the courtesy mirror is fitted also on the
driver’s sun visor. Carefully inspect the car to find fuel leaks,
e.g. in the engine compartment, under the
car or near the tank.
If no fuel leaks are found and the car can
be started again, press button Ato reset
the fuel system and the lights.
After a crash, remember to turn the igni-
tion key to STOPto prevent battery run-
down.
fig. 57F0G0223m
fig. 58F0G0069m
If, after a crash, you smell fu-
el or see leaks from the fuel
system, do not reset the switch to
avoid fine risk.
WARNINGThe cigar lighter gets very
hot. Be careful how you han-
dle it and make sure it is not used by
children: danger of fire or burns.
WARNING
The ashtray can be removed and can be
placed into the glass holder to be used al-
so by rear passengers.
Do not use the ashtray as waste paper
basket: it might set on fire in contact with
cigarette stubs.
032-059 Panda New GB 21-06-2007 13:48 Pagina 53

118
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
If, turning the ignition key to
MAR, the warning light U
does not turn on or if it turns
on glowing steadily or flash-
ing when travelling (on certain versions
together with the message on the dis-
play), contact Fiat Dealership as soon
as possible. Warning light Uoperation
can be checked by traffic agents by
proper equipment. Comply with laws
and regulations of the country where
you are driving.
ç
FUEL RESERVE
(amber)
Turning the ignition key to
MARthe warning light turns on, but it
should go off after few seconds.
The warning light turns on when about 5
litres fuel are left in the tank.
IMPORTANT The warning light flashes to
indicate a failure, contact Fiat Dealership
as soon as possible to have the system
checked.GLOW PLUG
WARMING
(Multijet versions -
amber)
GLOW PLUG WARMING
FAILURE
(Multijet versions - amber)
Glow plug warming
Turning the ignition key to MAR, the
warning light turns on and it will turn off
when glow plugs reach the preset tem-
perature. Start the engine immediately af-
ter warning light switching off.
IMPORTANT With hot ambient temper-
ature, warning light stays on for very short
time.
Glow plug warming failure
The warning light turns on when there is
a failure in the glow plug warming system.
Contact Fiat Dealership as soon as possi-
ble.
On certain versions the dedicated message
is displayed.
m
If the light flashes, it is necessary to release
the accelerator pedal to lower the speed
of the engine until the warning light stops
flashing; continue the journey at moder-
ate speed, trying to avoid driving condi-
tions that may cause further flashing and
contact Fiat Dealership as soon as possi-
ble.DIESEL PARTICULATE
FILTER CLOGGED
(1.3 Multijet versions
75 HP - amber)
Turning the ignition key to MARthe
warning light turns on, but it should go off
after few seconds.
The warning light turns on when the diesel
particulate filter is clogged and the driving
conditions do not enable to activate au-
tomatically the reclaiming procedure.
To enable reclaiming, i.e. cleaning the fil-
ter, keep the car running until the warn-
ing light turns off.
The display will show the dedicated mes-
sage.
h
113-122 Panda New GB 26-06-2007 11:04 Pagina 118

Power windows .................................. 59
Presetting for mounting the
“Isofix type” child restraint system.. 91
Pretensioners ...................................... 84
Protecting the environment ............. 79
Radio frequency remote control .... 195
– battery replacement .................... 11
– request for additional
remote controls............................. 11
Radio transmitters and
cellular telephones ........................... 77
Rear fog lights ...................................... 52
– bulb replacement .......................... 142
– control button .............................. 52
Rear sliding seats.................................. 33
Rear window washer.......................... 50
– control ............................................ 50
– fluid level ........................................ 164
Rear window wiper ........................... 50
– blades .............................................. 172
– control ............................................ 50
– nozzles ............................................ 173
Rearview mirrors................................. 36
– door mirrors ................................. 37
– driving mirror ................................ 36
– electric mirrors ............................. 37
Reconfigurable multifunction
display.................................................. 21
Rev counter.......................................... 16Reversing light ..................................... 142
Roof rack/ski rack .............................. 65
Rubber hoses ....................................... 171
Safety devices ..................................... 81
Seat adjustment ................................... 32
Seat belts............................................... 82
– general instructions ..................... 85
– height adjustment ......................... 82
– load limiters ................................... 85
– maintenance .................................. 86
– pretensioners ................................ 84
– use ................................................... 82
Seats ...................................................... 32
– cleaning ........................................... 175
– manually adjustable front seats .. 32
– rear sliding seats ........................... 33
Side/taillights ........................................ 48
– control ............................................ 48
– front bulb replacement................. 139
– rear bulb replacement.................. 142
Smart washing ..................................... 49
Snow chains ......................................... 111
Sound system ...................................... 76
Spark plugs............................................ 181
Speedometer........................................ 16
Starting the engine ............................. 102
– bump starting ................................ 126
– diesel engines ................................ 103 – battery replacement .................... 11
– request for additional remote
controls .......................................... 11
Key without remote control ........... 9
Load limiters ...................................... 85
Main beam headlights ....................... 48
– bulb replacement .......................... 140
– control ............................................ 48
– flashing ............................................ 48
Manual climate control system ........ 41
MSR system........................................... 71
Multifunction display........................... 19
Number plate light ............................ 143
Oddment compartments.................. 54
Paint ..................................................... 174
Parking .................................................. 104
Parking lights ........................................ 48
Parking sensors.................................... 74
Passenger's compartment
heating......................................39-39-44
Performance ........................................ 188
Plates...................................................... 178
– bodywork paint identification
plate ................................................. 179
– model plate .................................... 178
Pollen filter ........................................... 167
Power socket ...................................... 55
199
WARNING
LIGHTS AND
MESSAGES
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
197-204 Panda New GB 21-06-2007 13:54 Pagina 199