CD changer FIAT PANDA 2007 169 / 2.G Radio CD Tape Manual

75
RADIO WITH
COMPACT DISC AND MP3 CD PLAYER
RADIO WITH
TAPES PLAYER
RADIO WITH
COMPACT DISC PLAYER
The behaviour of the set during AutoSTore is as
follows:
❒at the beginning of the AutoSTore function all the
other functions are disabled;
❒pressing one of the radio function buttons, e.g.: 17
(PTY), 6 (N), 5 (
÷), 6 (O), 5 (˜), (7), (9), (10),
(13), (15), (16) the automatic storage process is
interrupted, the last station heard before
AutoSTore was turned on is tuned and the function
associated with the button pressed is run;
❒pressing button 14 (AF-TA) during AutoSTore will
interrupt it, the TA function (traffic information) will
be turned on/off and a new automatic storage
process will be started;
❒changing the listening source (Radio, Compact Disc,
CD Changer) during automatic storage will not
interrupt the AutoSTore function.
Activating the AutoSTore function in MW or LW
bands will automatically select the FMT band where
the function is then run.
IMPORTANT Sometimes the AutoSTore function is
unable to find 6 stations with a strong signal. In this
case the previous stations will be stored on the free
preset buttons.Listening to stored stations
Proceed as follows:
❒select the required frequency band (FM, MW, LW);
❒briefly press one of the six station storage buttons.
The display will show the number that corresponds to
the button.
In bands FM1, FM2 and FMT, if reception is poor and
the AF alternative frequency search function is active,
the station with the strongest signal that is
broadcasting the same programme will be sought
automatically.
AF function (alternative frequency search)
Within the RDS system the radio can work in two
different modes:
❒“AF ON”: alternative frequency search on (the
display shows “AF”);
❒“AF OFF”: alternative frequency search off.
051-098 ING 21-06-2007 15:49 Pagina 75

77
RADIO WITH
COMPACT DISC AND MP3 CD PLAYER
RADIO WITH
TAPES PLAYER
RADIO WITH
COMPACT DISC PLAYER
With the TA function (traffic information) it is
possible:
1) to search only RDS stations that transmit in the FM
band, enabled to broadcast traffic information;
2) to receive traffic information even if the CD player
or CD Changer is in use;
3) to receive traffic information at a predefined
minimum volume even with the radio volume off.
The operations to be carried out for each of the three
above conditions are listed below.
1) To receive stations enabled to broadcast traffic
information:
❒select band FM1, FM2 or FMT;
❒briefly press button 14 (AF-TA) so that the display
shows “TA”;
To store stations with TA on, carry out the storage
operations (see “Manual station storage”).2) If wishing to receive traffic information when
listening to a CD, before inserting the CD or starting
the CD Changer, in Telephone mode or with Mute
function on, tune to a station enabled to broadcast
traffic information (TP) and activate the TA function. If
while listening to a Compact Disc, this station
broadcasts traffic information, the CD will be
suspended temporarily and resumed again
automatically after the end of the message. At the start
of receiving traffic information the display will briefly
show the wording “TRAFFIC INFORMATION”, while
the display continues giving the last information
(frequency, etc.).
If the CD player is already working and at the same
time you want to receive traffic information, briefly
pressing button 14 (AF-TA) the radio tunes to the last
station heard in the FM band, the TA function is
activated and the traffic messages are transmitted. If
the station selected does not send traffic information,
the search for an enabled station starts automatically.
If wishing to interrupt the traffic information message,
briefly press button 14 (AF-TA) during transmission of
the message.
051-098 ING 21-06-2007 15:49 Pagina 77

78
RADIO WITH
COMPACT DISC AND MP3 CD PLAYER
RADIO WITH
TAPES PLAYER
RADIO WITH
COMPACT DISC PLAYER
3) To receive traffic information while not listening to
the radio:
❒turn on the TA function briefly pressing button 14
(AF-TA) so that the display shows “TA”;
❒tune to a station enabled to transmit traffic
information so that the display shows “TP” and turn
the volume to zero by turning the button/knob 18
(VOLUME ON/OFF).
This way, if that station broadcasts traffic information,
this will be heard at a minimum predefined volume.
IMPORTANT In certain countries radio stations exist
which, even if the TP function is on (the display shows
“TP”), do not transmit traffic information.
If the radio is working in the AM band, when button
14 (AF-TA) is pressed, it passes to the FM1 band on
the last station heard. If the station selected does not
broadcast traffic information the search for an enabled
station starts automatically.The volume with which the traffic bulletin is
transmitted varies depending on the listening volume:
❒listening volume below 20: traffic bulletin volume =
20 (fixed value);
❒listening volume above 20: same traffic bulletin
volume as the listening volume +1.
If the volume is changed during a traffic bulletin the
value is not shown on the display and the new value is
kept only for the bulletin in progress.
If the volume is changed during a traffic bulletin,
depending on the active audio source the following
cases may took place:
❒Radio on: a “beep” is given every 30 seconds;
❒Compact Disc, CD Changer (if installed), Telephone
or Mute on: a “beep” is given and the search for an
enabled station will start.
During a traffic bulletin it is possible to turn on sound
adjustment and the radio menu by pressing
respectively buttons 11 (MENU-PRESET SCAN) or 8
(AUDIO-LOUDNESS).
051-098 ING 21-06-2007 15:49 Pagina 78

82
RADIO WITH
COMPACT DISC AND MP3 CD PLAYER
RADIO WITH
TAPES PLAYER
RADIO WITH
COMPACT DISC PLAYER
Scrolling transmissions
It is possible to receive different programmes in the
same network and scroll them (in FM band only).
To activate this function keep button 14 (AF-TA)
pressed to activate the AF function. The scrolling may
begin pressing button 5 (
÷) or (˜).
All stations previously received (at least once) will be
stored with the corresponding PI code. With this
function on, radio stations can be tuned
forward/backward by pressing button 5 (
÷) or
(
˜).
IMPORTANT The station must have been received
previously at least once.
Stereophonic stations
If the signal received is weak, the device switches
automatically from Stereo to Mono.MENU
Functions of button 11 (MENU-PRESET SCAN)
To activate the menu function, briefly press button 11
(MENU-PRESET SCAN). The display shows the word
“MENU”.
To scroll the menu functions use buttons 6 (
N) or
(
O). To turn on/off the function selected, use buttons
5 (
÷) or (˜).
The display will show the current status of the
function selected.
The functions controlled by the menu are the
following:
❒USER EQ SETTING (equalizer setting, only if the
equalizer is on);
❒PRESET/USER/CLASSIC/ROCK/JAZZ (turning
on/off and choosing predefined equalizer
adjustments);
❒REGIONAL MODE (regional programmes);
❒CD DISPLAY (CD data display);
❒CDC DISPLAY (CD Changer data display, if
installed);
❒SENSITIVITY (tuning sensitivity);
051-098 ING 21-06-2007 15:49 Pagina 82

84
RADIO WITH
COMPACT DISC AND MP3 CD PLAYER
RADIO WITH
TAPES PLAYER
RADIO WITH
COMPACT DISC PLAYER
REGIONAL MODE function
(regional broadcast reception)
Certain national broadcasters, at determinate times of
the day, transmit regional programmes which differ
from region to region. This function makes it possible
to tune in only on local stations (regional). However if
a regional programme is heard and you wish to stay
tuned to it, the function must be activated.
To turn the function on/off use button 5 (
÷) or
(
˜).
The display will show the current status of the
function:
❒“REGIONAL MODE: ON”: function on;
❒“REGIONAL MODE: OFF”: function off.
If the function is off and a regional programme is tuned
that works in a determinate area and the car enters a
different area, the regional station of the new area is
received.
IMPORTANT When the function is off (“REGIONAL
MODE-OFF”) and the AF function is on (alternative
frequencies) the radio automatically tunes to the
frequency of the station selected with the strongest
signal.CD DISPLAY function
(Compact Disc data display)
With this function it is possible to choose the
information shown on the display, when listening to a
Compact Disc.
After choosing “CD” in the menu using buttons 6 (
N)
or (
O), the display shows “CD DISPLAY”. To change
the setting use buttons 5 (
÷) or (˜).
The display shows the setting among the two possible:
❒“TIME” (time elapsed from start of track);
❒“NAME” (CD name).
CDC DISPLAY function
(CD Changer data display)
(if installed)
This function can be chosen only if a CD Changer is
connected. In this case the display will show “CDC
DISPLAY”.
To change the function use buttons 5 (
÷) or (˜).
The display shows the setting among the three
possible:
❒“TIME” (time elapsed from start of track);
❒“CD NR” (CD number);
❒“NAME” (CD name).
051-098 ING 21-06-2007 15:49 Pagina 84

85
RADIO WITH
COMPACT DISC AND MP3 CD PLAYER
RADIO WITH
TAPES PLAYER
RADIO WITH
COMPACT DISC PLAYER
SENSITIVITY function
(tuner sensitivity adjustment)
With this function it is possible to change the
sensitivity of automatic station searching. When low
sensitivity “SENSITIVITY LOCAL” is set only stations
with excellent reception are sought; when high
sensitivity “SENSITIVITY DISTANCE” is set all stations
are sought. Therefore, if the car is in an area with a
considerable number of stations and you want to
choose only those with a strong signal, set to low
sensitivity “SENSITIVITY LOCAL”.
To set the sensitivity, use button 5 (
÷) or (˜).
The display will show the current status of the
function:
❒“SENSITIVITY: LOCAL”: low sensitivity;
❒“SENSITIVITY: DISTANCE”: high sensitivity.SVC SETTING function
(volume changing with speed)
The SVC function makes it possible to automatically
adapt the volume level to the speed of the car,
increasing it as the speed increases to maintain the
ratio with the noise level in the passenger
compartment.
To turn the function on/off use button 5 (
÷) or
(
˜). The display will show the current status of the
function:
❒“SVC SETTING: ON”: function on;
❒“SVC SETTING: OFF”: function off.
CD NAMING function
(allocating a name to a CD)
Use the CD NAMING function to give a name (max.
name length = 8 characters) to max. 30 CDs.
This function can be selected only if in Compact Disc
or CD Changer mode. To turn this function on, use
button 5 (
÷) or (˜): the display shows “CD
NAMING FUNCTION”. If the CD already has a name,
this will be shown on the display, if not, eight dashes
will be shown. If storage is no longer available for a
new name, the display will show the first name stored.
051-098 ING 21-06-2007 15:49 Pagina 85

90
RADIO WITH
COMPACT DISC AND MP3 CD PLAYER
RADIO WITH
TAPES PLAYER
RADIO WITH
COMPACT DISC PLAYER
❒pressing button 6 (N) or (O);
❒pressing a preset button (from 1 to 6);
❒turning the Mute function on;
❒changing the sound source;
❒pressing button 1 (SOURCE-SCAN), 11 (MENU-
PRESET SCAN) or 18 (AUDIO-LOUDNESS);
❒if the TA function is on and the station selected is
broadcasting a traffic bulletin.
The Scan function will stay active until it is stopped by
the user.
Repeat function (track repeat)
Press button 10 (4-RPT) to listen repeatedly to the last
track played: for about 2 seconds the display shows
“REPEAT TRACK”.
Press button 10 (4-RPT) again to turn the Repeat
function off: for about 2 seconds the display shows
“REPEAT OFF”.
After repeating a track the display shows for about 2
seconds “REPEAT TRACK”.
Changing the sound source, the function is turned off.
IMPORTANT When the Repeat function is turned on,
the Scan and Mix functions are turned off.Mix function (random track playing)
To start random playing of tracks on the Compact
Disc selected, press button 9 (5-MIX). A new track
will be played and for about 2 seconds the display will
show “MIX CD”.
Press button 9 (5-MIX) again to turn the function off:
for about 2 seconds the display will show “MIX OFF”.
When the Mix function is on, all the tracks in the
current CD or any CD in the CD Changer will be
played randomly.
After playing a track the display shows for about 2
seconds “MIX CD”.
Changing the sound source, the function is turned off.
IMPORTANT When the Mix function is turned on, the
Scan and Repeat functions are turned off.
051-098 ING 21-06-2007 15:49 Pagina 90

91
RADIO WITH
COMPACT DISC AND MP3 CD PLAYER
RADIO WITH
TAPES PLAYER
RADIO WITH
COMPACT DISC PLAYER
TPM function (CD playing sequence storage)
With the TPM function (Track Program Memory) it is
possible to store the sequence for playing tracks of a
CD, to be able to play them later in the sequence set.
To turn the function on briefly press button 16 (1-
TPM), while listening to a CD. When the function is
on, the display shows “TPM ON”. After playing the
track, the display will show again the word “TPM ON”
for about 2 seconds.
The TPM function cannot be activated if no track
sequence has been set. Pressing button 16 (1-TPM) the
display will show “NO TPM AVAILABLE”.
To store tracks, select the track required, then keep
button 16
(1-TPM) pressed until hearing the beep; the display will
show “TRACK IS STORED”. Repeat this procedure
for all the other tracks to be stored.
IMPORTANT It is possible to store max. 40 tracks per
CD.CLR function
(clearing CD track storage)
With the CLR (Clear) function it is possible:
❒to clear only one or all CD tracks stored with the
TPM function.
❒to clear the tracks stored with the TPM function
from all the CDs contained in the CD Changer.
To clear one track, select it with buttons 5 (
÷) or
(
˜) when the TPM function is on, then keep button
15 (2-CLR) pressed for about 3 seconds. The TPM
function is turned off, a beep is heard and the display
shows “ONE TRACK DELETED”.
To clear all the tracks stored of a CD, insert the
required CD, turn on the TPM function then press
button 15 (2-CLR) for about 6 seconds. The TPM
function is turned off, a double beep is heard after
about 2 and 4 seconds and the display shows
“ALL TRACKS DELETED”.
To clear all the tracks of all the CDs contained in the
CD changer, press button 15
(2-CLR) for over 8 seconds. Three beeps are heard
after about 2, 4 and 8 seconds and the display shows
“COMPLETE TPM CLEARED”.
051-098 ING 21-06-2007 15:49 Pagina 91

92
RADIO WITH
COMPACT DISC AND MP3 CD PLAYER
RADIO WITH
TAPES PLAYER
RADIO WITH
COMPACT DISC PLAYER
CD CHANGER (CDC)
(where provided)
CD Changer (multiple Compact Disc player) for 5
discs, to be located in the glove compartment, is
available upon request.
Selecting the CD Changer
Turn on the set, then press briefly button 1
(SOURCE-SCAN) to select the “CHANGER”
function.
Inserting/ejecting a CD
To insert CDs into the CD Changer: insert gently a
CD with the label upwards into the CD Changer
compartment and push it gently to the stop. The
powered loading system will position it correctly.
To eject CDs from the CD Changer: keep pressed the
button with the number corresponding to the CD to
be ejected, set near the CD compartment.Possible error messages
Error messages will be displayed in the following cases:
❒no CD in the CD Changer: the display will show
“CD ERROR” until changing the sound source;
❒selected CD is illegible (CD not in the selected
position or CD not inserted properly): the display
shows “CD ERROR” after the number of the
selected CD for about 2 seconds. The next CD will
be selected; if there are no other CDs or if they are
also illegible the display will show the wording “NO
CD” until the sound source is changed;
❒error in CD reading: the display shows “CD
ERROR” for about 2 seconds. The next CD will be
selected; if there are no other CDs in the CD
Changer (after the last CD search will restart from
the first one) or if they are also illegible the display
will show the wording “NO CD” until the sound
source is changed;
❒a CD-ROM is inserted: next CD will be selected.
051-098 ING 21-06-2007 15:49 Pagina 92

93
RADIO WITH
COMPACT DISC AND MP3 CD PLAYER
RADIO WITH
TAPES PLAYER
RADIO WITH
COMPACT DISC PLAYER
Display information
When the CD Changer is working, the display shows
the following information which means:
❒“T05”: shows the number of the track on the CD;
❒“03:42”: shows the time elapsed since the start of
the track (if the corresponding Menu function is on);
❒“CD 04”: the number of the CD in the loader.
❒“XXXXXXX”: shows the name allocated to the
CD.
Choosing the CD
Press button 6 (
N) to select the next CD and button
6 (
O) to select the previous CD. If in the menu the
CD time display function was selected, this will be
replaced for about 2 seconds by the CD number.
If the loader does not contain a disc in the position
selected, the display briefly shows the wording “NO
CD”, and the next CD is played automatically.Select track (forward/backward)
Briefly press button 5 (
÷) to play the previous track
of the CD chosen and button 5 (
˜) to play the next
one. Tracks are played in sequence: after the last
track, the first one will be played and vice versa.
To select tracks continuously, keep the button
pressed.
If playing the track started more than 3 seconds ago,
pressing briefly button 5 (÷) the track is played again
from the start. In this case if wanting to play the
previous track, press the button twice consecutively.
Fast forward/backward
Keep button 5 (
÷) pressed to move the track
selected backward at high speed and keep button 5
(
˜) pressed to move it quickly forward. Fast
forward/backward is stopped once the button is
released.
If the CD number or CD name display function was
selected in the menu, this will be replaced for about 2
seconds by the CD time display function.
051-098 ING 21-06-2007 15:49 Pagina 93