check engine light FIAT PUNTO EVO 2009 1.G User Guide

162
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
AIRBAG FAILURE (red)
When the ignition key is moved to MAR position,
the warnintg light turns on but should go off af-
ter a few seconds.
The warning light stays on constantly if there is a failure
in the airbag system. A specific message is displayed on cer-
tain versions.
¬
If the warning light ¬does not come on
when turning the key to MAR or stays on
during car travel, a failure may be present in the
restraint systems. If this is the case, the airbags
or pretensioners may not be deployed after an im-
pact or, in a minor number of cases, they may be
deployed accidentally. Contact a Fiat Dealership
immediately to have the system checked before
driving off.
WARNING
A problem with the warning light ¬(light
off) is indicated by the warning light “,
which indicates the front passenger airbag is de-
activated, flashing for more than the usual four
seconds.
WARNING
OVERHEATED ENGINE COOLANT
(red)
When the ignition key is moved to MAR position,
the warnintg light turns on but should go off after a few
seconds. The warning light turns on when the engine is
overheated. If the warning light comes on, proceed as fol-
lows:
❒when driving normally: stop the car, switch off the en-
gine and check that the water level in the reservoir is
not below the MIN mark. If it is not, wait for a few min-
utes for the engine to cool down then slowly and care-
fully open the cap, top-up with coolant and check that
the level is between the MIN and MAX marks. Also
visually check for leaks. Go to a Fiat Dealership if the
warning light comes on again when the engine is next
started.
❒if the vehicle is used under demanding conditions (e.g.
towing trailers uphill or fully loaded): slow down and,
if the light stays on, stop the car. Stop for 2 or 3 min-
utes with the engine running and slightly accelerated to
assist better coolant circulation. Then switch the en-
gine off. Check correct fluid level as described above.
IMPORTANT On particularly demanding journeys, it is ad-
visable to keep the engine on and slightly accelerated for
a few minutes before switching it off.
A specific message is displayed on certain versions.
ç
161-174 PUNTO FL EN 3ed 9-12-2009 13:40 Pagina 162

165
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
SEAT BELT NOT FASTENED (red)
The warning light on the display lights up per-
manently when the car is not moving and the dri-
ver’s seat belt is not correctly fastened. It will flash,
and be accompanied by an audible warning, if the front seat
belts are not correctly fastened when the vehicle is mov-
ing. The SBR (Seat Belt Reminder) system’s audible warn-
ing can be disabled only by a Fiat Dealership. On some ver-
sions the system can be reactivated from the setup menu.
<
LOW ENGINE OIL LEVEL (red)
(for versions/markets where provided)
When turning the ignition key to MAR, the
warning light turns on but it should go off after a
few seconds. This warning light where provided comes on
when the engine oil level falls below the minimum rec-
ommended value. Restore the correct engine oil level (see
“Checking fluid levels” in the “Servicing and care” section).
A specific message is displayed on certain versions.
k
EBD FAULT (red)
(amber)
Warning lights
xand >lit at the
same time with the engine running in-
dicates an EBD system failure or that the system is not
available. This may cause premature locking of the rear
wheels in the event of violent braking, causing the car to
swerve. Drive very carefully to a Fiat Dealership to have
the system inspected immediately.
On some versions the display shows the associated mes-
sage.> x
INJECTION SYSTEM FAULT
(Multijet versions – amber)
EOBD SYSTEM FAULT
(petrol versions – amber)
Injection system failure
Under normal conditions, turning the ignition key to MAR,
the warning light turns on but it should go off after the en-
gine starts.
If the warning light stays on or comes on when travelling,
it means there is a fault in the injection system which could
cause loss of performance, poor handling and high fuel con-
sumption levels.
A specific message is displayed on certain versions. Un-
der these conditions, the vehicle can continue travelling at
moderate speed without demanding excessive effort from
the engine. In any case, you should go to a Fiat Dealer-
ship as soon as possible.
U
161-174 PUNTO FL EN 3ed 9-12-2009 13:40 Pagina 165

166
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
Go to a Fiat Dealership as soon as possi-
ble if warning light Udoes not light up
when the key is turned to MAR or if, while trav-
elling, the warning light comes on either perma-
nently or flashing (along with a message on the
display on certain versions). The operation of the
Uwarning light may be checked by traffic police
using appropriate equipment. Follow the laws in
force in the country where you are driving.
WARNING
FRONT PASSENGER AIRBAG
DEACTIVATED (amber)
The warning light
“comes on when the front
passenger airbag is disabled.
With the front passenger air bag enabled, when the igni-
tion key is turned to MAR the
“warning light comes on
constantly for about 4 seconds, flashes for another 4 sec-
onds and then should go out.
“
Engine management system failure – EOBD
Under normal conditions, turning the ignition key to MAR,
the warning light turns on but it should go off after the en-
gine starts. This indicates that the warning light is work-
ing correctly. If the warning light either stays on or comes
on during car travel:
❒on permanently: this means there is a fault in the sup-
ply/ignition system which could cause high exhaust
emissions, loss of performance, poor handling and high
fuel consumption levels.
A specific message is displayed on certain versions.
Under these conditions, the vehicle can continue travel-
ling at moderate speed without demanding excessive ef-
fort from the engine. Prolonged use of the car with the
warning light on may cause damage. Go to a Fiat Dealer-
ship as soon as possible. The warning light goes out after
the fault disappears, but the indication is stored in the sys-
tem.
❒flashing: this indicates possible damage to the catalytic
converter (see “EOBD system” in the “Dashboard and
controls” section).
If the light flashes, come off the accelerator pedal to re-
duce engine revs until the warning light stops flashing; con-
tinue the journey at moderate speed, trying to avoid dri-
ving conditions that may cause further flashing, and get
to a Fiat Dealership as soon as possible.For versions/markets, where provided, the
Uwarning
light in the instrument panel does not have the EOBD func-
tion (European On Board Diagnosis) but only that of sig-
nalling that the injection system is not working perfectly.
161-174 PUNTO FL EN 3ed 9-12-2009 13:40 Pagina 166

167
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
FUEL RESERVE (amber)
Turning the key to the MAR position illuminates
the warning light, but it will switch off after a few
seconds.
The warning light turns on when about 7 litres of fuel are
left in the tank.
IMPORTANT The warning light will blink to indicate a sys-
tem failure. If this happens, go to a Fiat Dealership to have
the system checked.
Warning light “indicates a failure of warn-
ing light ¬. This condition is indicated by
intermittent blinking of warning light “for longer
than 4 seconds. In this case, warning light ¬may
not be indicating that there is a fault in the restraint
systems. Before driving off, contact a Fiat Dealer-
ship to have the system checked immediately.
WARNING
ç
ABS SYSTEM FAULT (amber)
Turning the key to the MAR position illuminates
the warning light, but it will switch off after a few
seconds.
The warning light comes on when the system is either not
working properly or not available. Under these circum-
stances, the braking system will work as normal but without
the extra performance offered by the ABS system. Drive
carefully and go to a Fiat Dealership as soon as possible.
On some versions the display shows the associated message.
>
GLOW PLUG PREHEATING
(Multijet versions – amber)
GLOW PLUG PREHEATING FAULT
(Multijet versions – amber)
Glow plugs
This warning light comes on when the key is turned to
MAR. It will go out as soon as the glow plugs have reached
a preset temperature. Start the engine as soon as the
warning light goes out.
IMPORTANT When it is particularly warm outside, the
warning light stays on for an extremely short time.
Glow plug preheating fault
The warning light flashes if there is a fault in the preheat-
ing system. Go to a Fiat Dealership as soon as possible.
A specific message is displayed on certain versions.
m
161-174 PUNTO FL EN 3ed 9-12-2009 13:40 Pagina 167

STARTING THE ENGINE
EMERGENCY STARTING
If the instrument panel warning light
Ystays on perma-
nently, contact a Fiat Dealership immediately.
JUMP STARTING fig. 150
If the battery is flat, the engine may be started using an aux-
iliary battery with an equal or slightly higher capacity than the
flat one. It is advisable to contact a Fiat Dealership so the bat-
tery can be checked/replaced.
IN AN EMERGENCY
In an emergency we recommend that you call the freephone number found in the Warranty Booklet. You can
also go to the www.fiat.com website to find your nearest Fiat Dealership.
This procedure must be performed by ex-
perts because incorrect actions may cause
considerable electrical discharge. Furthermore,
battery fluid is poisonous and corrosive: avoid con-
tact with skin and eyes. Keep naked flames and
lit cigarettes away from the battery. Do not cre-
ate sparks.
WARNING
Proceed as follows to start the car:
❒connect the positive terminals (+ sign near the termi-
nal) of the two batteries with a jump lead;
❒with a second lead, connect the negative terminal (–) of
the auxiliary battery to an earthing point Eon the en-
gine or the gearbox of the car to be started;
❒ start the engine;
❒when the engine has been started, follow the sequence
above in reverse order to remove the leads.
If after a few attempts the engine does not start, do not
keep trying but contact a Fiat Dealership.
fig. 150F0U00134m
175
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
175-210 PUNTO FL EN 3ed 9-12-2009 13:41 Pagina 175

Repair and refit the standard wheel as
soon as possible. Do not apply grease to
the bolt threads before assembly: they might spon-
taneously unscrew.
WARNING
The jack may be used to replace wheels
only on the car which it equips or other
cars of the same model. Never use the jack for
other purposes, such as lifting other models. Nev-
er use the jack to carry out repairs under the car.
Incorrect positioning of the jack may cause the
car to fall. Do not use the jack for loads higher
than the one shown on its label.
WARNING
If the hub cap is not fitted correctly, it may
come off when the car is travelling. Nev-
er tamper with the inflation valve. Never intro-
duce tools of any kind between the rim and the
tyre. Check tyre and spare wheel pressures regu-
larly, referring to the values shown in the “Tech-
nical specifications” section.
WARNING
Important notes:
❒the jack weight is 1.76 kg;
❒the jack requires no adjustment;
❒the jack cannot be repaired. If it breaks, it must be re-
placed with the same type;
❒no tool other than its cranking device may be fitted on
the jack.
To change a tyre, proceed as follows:
❒stop the car where it is not a danger to other road users
and you can replace the wheel safely. The ground should
be flat and solid;
❒turn the engine off and engage the handbrake;
❒engage first gear or reverse;
❒wear the reflective safety jacket (compulsory by law in
certain countries) before getting out of the car;
❒open the boot and lift the carpet or remove the cargo
box (for versions/markets where provided);
❒ unscrew the locking device A-fig. 151;
❒take out the tool container C-fig. 151 and put it along-
side the wheel to be changed;
❒take out the spare wheel B-fig. 151;
❒loosen the bolts of the wheel to be replaced by about
one turn with the wrench provided E-fig. 152; if you
have alloy wheels, rock the car to make it easier to sep-
arate the rim from the wheel hub;
177
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
175-210 PUNTO FL EN 3ed 9-12-2009 13:41 Pagina 177

Replace the cylinder containing out-of-
date sealant fluid. Dispose of the cylinder
and the sealant liquid properly. Dispose ac-
cording to the national and local laws in force.
F0U0142mfig. 159F0U0141mfig. 158
INFLATION PROCEDURE
Put on the protective gloves provided
with the quick tyre repair kit.
WARNING
❒Make sure the handbrake is on. Unscrew the tyre valve
cap, take out the flexible filler tube A-fig. 158 and tight-
en the ring nut B on the tyre valve;
❒make sure that switch D-fig. 159 for the compressor
is in position 0 (off), start the engine, insert pin E-fig. 160
into the nearest socket and switch on the compressor
by moving switch D-fig. 159 to position 1 (on) Inflate
the tyre to the pressure specified in the “Tyre pressure”
paragraph in the “Technical specifications” section.
For a more accurate reading, check pressure gauge F-fig.
159 with the compressor off;
❒if after 5 minutes you cannot reach at least 1.5 bar, un-
plug the compressor from the valve and the socket, then
move the car forward about ten metres in order to dis-
tribute the sealant inside the tyre evenly, then repeat the
inflation operation;
183
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
175-210 PUNTO FL EN 3ed 9-12-2009 13:42 Pagina 183

F0U0144mfig. 161F0U0143mfig. 160
❒if after this operation you still cannot reach at least 1.8
bar after 5 minutes, do not resume driving because the
tyre is too damaged and the quick tyre repair kit cannot
guarantee suitable sealing. Contact a Fiat Dealership;
❒if you do reach the tyre pressure specified in the “Tyre
pressure” paragraph in the “Technical specifications” sec-
tion, start driving immediately;
184
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
Apply the adhesive label where it can be
easily seen by the driver as a reminder that
the tyre has been treated with the quick repair kit.
Drive carefully, particularly on bends. Do not ex-
ceed 80 km/h. Do not accelerate or brake sud-
denly.
WARNING
❒after driving for about 10 minutes, stop and check the
tyre pressure again; remember to put the handbrake on;
If the pressure has fallen below 1.8 bar, do
not drive any further: the Fix & Go automatic
quick tyre repair kit cannot guarantee proper hold
because the tyre is too damaged. Contact a Fiat
Dealership.
WARNING
❒If you get a pressure reading of at least 1.8 bar, restore
the proper pressure (with engine running and handbrake
on) and restart.
❒drive with the utmost care to the nearest Fiat Dealer-
ship.
175-210 PUNTO FL EN 3ed 9-12-2009 13:42 Pagina 184

●● ●● ● ●
●● ●● ● ●
●● ●● ● ●
●● ●● ● ●
●● ●● ● ●
●● ●
●● ●● ● ●
●● ●● ● ●
●● ●● ● ●
●● ●● ● ●
●●
●●
●●
●● ●
●● ●● ● ●
212
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
SCHEDULED SERVICING PLAN
EURO 4/EURO 5 PETROL AND EURO 4 DIESEL VERSIONS
Thousands of kilometres 30 60 90 120 150 180
Check tyre condition/wear and adjust pressure if required
Check operation of lighting system (headlamps, direction indicators,
hazard warning lights, boot, passenger compartment, glove box,
instrument panel warning lights, etc.)
Check operation of windscreen washer system and adjust nozzles
if necessary.
Check windscreen/rear window wiper blade position/wear
Check conditions and wear of front/rear disc brake pads
(for versions/markets where provided) and operation of pad wear indicator
Check condition and wear of rear drum brake linings
Visually inspect the conditions of: bodywork,
underbody protection, pipes and tubes
(exhaust – fuel – brakes), rubber parts (boots, sleeves, bushes, etc.)
Check cleanliness of bonnet and boot locks, and the cleanliness
and lubrication of linkages
Check and, if necessary, top up fluid levels (brakes/hydraulic
clutch, windscreen washer, battery, engine coolant, etc.)
Check the handbrake lever stroke and adjust it, if necessary
Visually inspect the condition of accessory drive belt/s.
Visually inspect the condition of toothed timing belt
Check tension of accessory drive belt/s, and adjust if necessary
(versions 1.2 – 1.4 heated)
Check and, if necessary, adjust tappet clearance (1.2 8v – 1.4 8vversions)
Check exhaust gas emissions
211-234 PUNTO FL EN 3ed 9-12-2009 13:38 Pagina 212

213
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
●● ●● ● ●
●
●
●● ●● ● ●
●● ●
●● ●
●● ●● ● ●
●● ●● ● ●
●● ●
●● ●● ● ●
Thousands of kilometres 30 60 90 120 150 180
Check engine management system operation (via diagnostic socket)
Replace accessory drive belt/s
Replace toothed timing belt (*)
Replace spark plugs (petrol versions) (1)
Replace fuel filter (diesel versions)
Replace air filter cartridge (petrol versions) (❏)
Change engine oil and replace oil filter (petrol versions)
(or every 24 months) (2)
Change engine oil and replace oil filter
(EURO 4 diesel versions without DPF) (or every 24 months)
Change engine oil and oil filter (diesel EURO 4 versions with DPF) (Õ) (3)
Change brake fluid (or every 24 months)
Replace pollen filter (or every 15 months)
(*) Regardless of the distance covered, the timing belt should be replaced every 4 years for particularly demanding use (cold climates, city dri-
ving, idling for a long time, dusty areas) or, in any case, every 5 years.
(❏) For Euro 4 diesel versions, the air filter cartridge should be replaced every 30,000 km.
(Õ) The engine oil and the filter must be replaced when the warning light on the dashboard comes on (see the “Warning lights and messages”
section) or at least every 24 months.
(1)For 1.4 Turbo Multi Air versions, in order to guarantee correct operation and prevent serious damage to
the engine, it is essential to observe the following:
– only use spark plugs specifically certified for 1.4 Turbo Multi Air engines; all spark plugs should be of the
same type and brand (see the “Engine” paragraph);
– adhere strictly to the spark plug replacement intervals detailed in the Scheduled Servicing Plan;
– it is advisable to have this performed at a Fiat Dealership.
(2)If the car is mainly used in towns and cities, change the engine oil and filter every 12 months.
(3)If the car is mainly used in cities or travels less than 10,000 km a year, change the engine oil and filter every 12 months.
211-234 PUNTO FL EN 3ed 9-12-2009 13:38 Pagina 213