display FIAT PUNTO EVO 2009 1.G Radio CD MP3 Manual

INTRODUCTION
FUNCTIONS AND
ADJUSTMENTS
RADIO
CD PLAYER
CD MP3
PLAYER
18
QUICK
GUIDE
SPEED VOLUME function
(volume change based on speed)
This function allows the volume level to
be adjusted automatically depending on
the speed of the vehicle, increasing it as
the speed increases to maintain the same
balance with the noise level inside the pas-
senger compartment. To turn the function
on/off, press the ¯/ ˙buttons. The
words Speed volume should appear on the
display followed by the current status of
the function:
❒Off: function deactivated
❒Low: function activated
(low setting)
❒High: function activated
(high setting).RADIO ON VOL function
(radio volume maximum limit acti-
vation/deactivation)
This function makes it possile to acti-
vate/deactivate the maximum volume lim-
it when turning the radio on.
The display shows the function status:
❒“Radio on vol – Limit on”: when the ra-
dio is switched on the volume level will
be:
– if the volume level is equal to or high-
er than the maximum value, the ra-
dio will come on at the maximum
volume;
– if the volume level is between the
minimum and maximum values, the
radio will come on at the same vol-
ume as before it was switched off;
– if the volume level is equal to or low-
er than the minimum value, the radio
will come on at the minimum volume.
❒“Radio on vol – Limit off”: the radio will
come on at the volume level it was at
before switching off. The volume may
be between 0 and 40.
Use the ¯/ ˙buttons to change the set-
ting.NOTES
❒Using the Menu it is only possible to ad-
just the activation/deactivation of the
function and not the minimum or max-
imum volume setting.
❒If the “TA” or “TEL” functions or an
outside audio source are activated
when the radio is turned on, the radio
will come on at the volume set for
these sources. When the outside audio
source is deactivated, the volume can
be adjusted between the minimum and
maximum levels.
❒If the battery charge is low, it will not
be possible to adjust the volume be-
tween the minimum and maximum lev-
els.
603_97_285 Radio Punto FL GB 1ed 8-09-2009 9:55 Pagina 18

19
INTRODUCTION
FUNCTIONS AND
ADJUSTMENTS
RADIO
CD PLAYER
CD MP3
PLAYER QUICK
GUIDE
EXTERNAL AUDIO function
(telephone volume adjustment)
This function makes it possible to adjust
(settings from 1 to 40), by turning the con-
trol fig. 1or pressing the ¯/ ˙buttons
or exclude (OFF setting) the volume of the
Telephone, the Blue&Me™(except the
Media Player function).
The display shows the current function
status:
❒“EXT Audio Off”: function deactivated.
❒“EXT Audio Volume 23”: function acti-
vated with volume setting 23.RADIO OFF function
(on and off mode)
This function is used to select the mode
of turning off the radio between two dif-
ferent procedures. To activate the func-
tion, use the ¯or ˙buttons.
The selected mode will appear on the dis-
play:
❒“00 MIN”: the radio turns off automat-
ically in connection with the ignition
key; the radio turns off automatically as
soon as the key is turned to the STOP
position;
❒“20 MIN”: the radio turns off indepen-
dently from the ignition key; the radio
remains on for a maximum period of 20
minutes after the key has been turned
to the STOP position.
SYSTEM RESET function
This function is used to restore all settings
to the factory values. The options are:
❒NO: no restore intervention;
❒YES: the default parameters are re-
stored. The display will show Resetting
during this operation. At the end of the
operation, the source does not change
and the previous situation will be dis-
played.TELEPHONE PREPARATION
If a hands-free kit is installed on the car,
when there is an incoming phonecall the
radio audio will be connected to the tele-
phone output. The telephone volume is
always fixed, but it can be adjusted dur-
ing a conversation using the rotating con-
trol fig. 1.
The fixed telephone audio volume can be
adjusted using the “EXT Audio” function
in the Menu. The word PHONE will ap-
pear on the display during the deactivation
of the audio for the phonecall.
603_97_285 Radio Punto FL GB 1ed 8-09-2009 9:55 Pagina 19

INTRODUCTION
FUNCTIONS AND
ADJUSTMENTS
RADIO
CD PLAYER
CD MP3
PLAYER
20
QUICK
GUIDE
ANTI-THEFT PROTECTION
The radio is equipped with an anti-theft
protection system based on the exchange
of information between the radio and the
electronic control unit (Body Computer)
on the vehicle.
This system guarantees maximum securi-
ty and avoids the secret code having to be
entered every time after the radio pow-
er supply is disconnected.
If the outcome of the check is positive, the
radio will start to work, whilst if the codes
compared are not the same or if the elec-
tronic control unit (Body Computer) is re-
placed, the equipment will notify the user
of the need to enter the password fol-
lowing the procedure in the paragraph be-
low.Entering the password
When the radio is switched on, if the pass-
word is requested, the display will show
“Radio code” for about 2 seconds fol-
lowed by four dashes “- - - -”.
The password is made up of four numbers
from 1 to 6, each corresponding to one of
the dashes.
To enter the first number, press the but-
ton corresponding to the preset stations
(from 1 to 6). Enter the other code num-
bers in the same way.
If the four digits are not entered within 20
seconds, the display will show “Enter code
- - - -”. This event is not considered an in-
correct entering of the code.
After entering the fourth digit (within 20
seconds), the car radio will start to work.
If an incorrect code is entered, the radio
will emit a sound and the display will show
“Radio blocked/wait” to notify the user of
the need to enter the correct code.
Each time the user enters an incorrect
code, the waiting time will gradually in-
crease (1 min, 2 min, 4 min, 8 min, 16 min,
30 min,1h, 2h, 4h, 8h, 16h, 24h) up to a
maximum of 24 hours. The waiting time
will be shown on the display by “Radio
blocked/wait”. After the message disap-
pears, the code entering procedure may
be started again.Code card
This document certifies ownership of the
car radio. The Code Card contains the
model of the radio, the serial number and
the password.
IMPORTANT Keep the Code Card some-
where safe so that the authorities can be
supplied with the relevant information if
the radio is stolen.
603_97_285 Radio Punto FL GB 1ed 8-09-2009 9:55 Pagina 20

21
INTRODUCTION
FUNCTIONS AND
ADJUSTMENTS
RADIO
CD PLAYER
CD MP3
PLAYER QUICK
GUIDE
FREQUENCY BAND
SELECTION
With the Radio mode active, press the
FMas or AM button briefly and repeated-
ly to select the desired reception band.
Each time the button is pressed the fol-
lowing bands are selected cyclically:
❒Pressing the FMas button: “FM1”,
“FM2” o “FMA”;
❒Pressing the AM button: “MW”.
Each band is highlighted by the name in the
display. The last station selected on the re-
spective frequency band will be tuned in-
to.
The FM band is divided into sections: FM1,
FM1 or “FMA”; the FMA reception band
is reserved for broadcasters stored auto-
matically using the AutoSTore function.PRESELECTION BUTTONS
The buttons numbered from 1 to 6 are
used to set the following preselections:
❒18 on the FM band FM (6 on FM1, 6 on
FM2, 6 on FMT or “FMA” (on some
versions);
❒12 on the MW band;
To listen to a preset station, select the de-
sired frequency band and then briefly press
the corresponding preset button (from 1
to 6).
By pressing the preset button for more
than 2 seconds, the tuned station will be
stored. The storing phase is confirmed by
an acoustic signal. INTRODUCTION
When the radio is turned on the last func-
tion selected before it was switched off
is activated: Radio, CD, CD MP3 or Me-
dia Player (only with Blue&Me™).
To select the Radio function when an-
other audio source is being listened to,
briefly press the FMas or AM buttons de-
pending on the desired band.
Once the Radio mode has been activated,
the display will show the name (RDS sta-
tions only) and the frequency of the se-
lected radio station, the frequency band
selected (e.g. FM1) and the preselect but-
ton number (e.g. P1).
R R
A A
D D
I I
O O
( (
T T
u u
n n
e e
r r
) )
603_97_285 Radio Punto FL GB 1ed 8-09-2009 9:55 Pagina 21

25
INTRODUCTION
FUNCTIONS AND
ADJUSTMENTS
RADIO
CD PLAYER
CD MP3
PLAYER QUICK
GUIDE
INTRODUCTION
This chapter describes the variants re-
garding the operation of the CD player: as
far as the operation of the radio is con-
cerned, refer to the description in the
“Functions and Adjustments” chapter.CD PLAYER SELECTION
To activate the CD player built-into the
equipment, proceed as follows:
❒load a CD with the equipment switched
on: the first track will start to play;
or
❒if a CD has already been loaded, turn
on the car radio and then briefly press
the CD button to select the “CD” func-
tion mode: the last track listened to will
start to play.
It is advisable to use original CDs to en-
sure optimum playing. If CD-R/RWs are
used, we recommend using good quality
media that are burned at the slowest
speed possible.CD LOADING/EJECTION
To load the CD, insert it gently into the
slot to activate the motorized loading sys-
tem, which will position it correctly.
The CD can be loaded with the radio
switched off and the ignition key in the
MAR position: in this case the radio will
remain off. When the radio is turned on,
the last source listened to prior to switch-
ing off will be activated.
When a CD is loaded the display will show
“CD-IN” and the words “CD Reading”.
They will remain displayed for the entire
time required for the radio to read the
CD tracks. When this time has elapsed the
radio will automatically start playing the
first track.
C C
D D
P P
L L
A A
Y Y
E E
R R
603_97_285 Radio Punto FL GB 1ed 8-09-2009 9:55 Pagina 25

INTRODUCTION
FUNCTIONS AND
ADJUSTMENTS
RADIO
CD PLAYER
CD MP3
PLAYER
26
QUICK
GUIDE
Press the ˚button (EJECT) with the ra-
dio on to activate the motorized ejection
of the CD. After ejection, the last audio
source listened to before playing the CD
will be heard.
If the CD is not removed from the radio,
it will automatically be reloaded about 20
seconds later and the Tuner mode will be
tuned into (Radio).
The CD cannot be ejected if the radio is
off.
If the ejected CD is loaded without hav-
ing removed it completely from the slot,
the radio will not switch to the CD
source.Possible error messages
If the CD loaded cannot be read (e.g. a CD
ROM has been inserted or the CD is in-
serted the wrong way round or there is
reading error) the display will show the
words “CD Disc error”.
The CD will then be ejected and the au-
dio source activated prior to the CD
mode selection will be heard.
With an outside audio source activated
(TA, ALARM or Phone), the CD that can-
not be read will be not be ejected until
these functions are over. At the end, with
the CD mode activated, the display will
show the words “CD Disc error” for a
few seconds and then the CD will be
ejected.DISPLAY INFORMATION
When the CD player is working, the dis-
play will show information which has the
following meaning:
❒“CD Track 5”: indicates the numer of
the CD track;
❒“03.42”: indicates the time elapsed since
the start of the track (if the relevant
Menu function is activated).
603_97_285 Radio Punto FL GB 1ed 8-09-2009 9:55 Pagina 26

27
INTRODUCTION
FUNCTIONS AND
ADJUSTMENTS
RADIO
CD PLAYER
CD MP3
PLAYER QUICK
GUIDE
TRACK SELECTION
(forward/backward)
Briefly press the ¯button to play the pre-
vious CD track and the ˙ button to play
the next track. The tracks are selected
cyclically: the first track is selected after
the last track and vice versa.
If the track has been played for more than
3 seconds, pressing the button ˙will
cause the track to be started again from
the beginning. In this case, if you want to
play the previous track, press the button
twice consecutively.TRACK FAST
FORWARD/REWIND
Keep the ˙button pressed down to fast
forward the selected track and keep the
button ¯pressed down to fast rewind the
track. The fast forward/back will stop once
the button is released.PAUSE FUNCTION
To pause the CD player, press the MUTE
button. The words “CD Pause” will ap-
pear on the display.
To resume listening to the track, press the
MUTE button again.
If another audio source is selected, the
pause function is turned off.
603_97_285 Radio Punto FL GB 1ed 8-09-2009 9:55 Pagina 27

29
INTRODUCTION
FUNCTIONS AND
ADJUSTMENTS
RADIO
CD PLAYER
CD MP3
PLAYER
QUICK
GUIDE
SELECTING MP3 SESSIONS
WITH HYBRID DISCS
If a hybrid disc is inserted (Mixed Mode,
Enhanced, CD-Extra) also containing MP3
files, the radio automatically starts play-
ing the audio session. It is possible to move
to the MP3 session whilst playing by keep-
ing the MEDIA button pressed for more
than 2 seconds.
IMPORTANT When the function is acti-
vated the radio may take a few seconds to
start playing. Whilst checking the disc the
display will show “CD Reading”. If no MP3
files are detected, the radio will resume
playing the audio session from the point
where it was interrupted.
DISPLAY INFORMATION
Id3-tag information
display
In addition to the information relating to
the time elapsed, the name of the folder
and the name of the file, the radio is also
capable of display ID3-TAG information
relating to the Title track, Artist and Au-
thor.The name of the MP3 folder shown on the
display corresponds to the name with
which the folder was stored on the CD,
followed by an asterisk.
Example of a complete MP3 folder name:
BEST OF *.
If you wish to display one of the ID3-TAG
pieces of information (Title, Artist, Album)
and this information has not been record-
ed for the track played, the information
will be replaced by information relating to
the name of the file.
SELECTION OF
NEXT/PREVIOUS FOLDER
Press the ▲button to select the next fold-
er or the ▼button to select the previ-
ous folder. The display will show the num-
ber and the name of the folder (e.g. “DIR
2 XXXXXX”).
XXXXXX: name of the folder (the display
will only show the first 8 characters).
The folders are selected cyclically: the first
folder is selected after the last folder and
vice versa. If no other folder/track is selected during
the next 2 seconds, the first track con-
tained in the new folder will be played.
If the last track on the folder currently se-
lected is being played, the next folder will
be played.
STRUCTURE OF THE FOLDERS
The radio with MP3 player:
❒only recognizes the folders that effec-
tively contain MP3 format files
❒if the MP3 files on a CD-ROM are
structured in “sub-folders”, their struc-
ture is compressed to a single level
structure where the “sub-folders” are
taken to the level of the main folders.
603_97_285 Radio Punto FL GB 1ed 8-09-2009 9:55 Pagina 29

30
GENERAL
Sound volume low
The Fader function should be adjusted to
“F” (front) values to prevent the reduction
in radio output power and the cancelling
of the volume if the Fader level adjustment
is R+9.
Source cannot be selected
Nothing has been loaded. Load the CD or
CD MP3 to be played.CD PLAYER
The CD does not play
The CD is dirty. Clean the CD.
The CD is scratched. Try and use anoth-
er CD.
The CD cannot be loaded.
A CD is already loaded. Press the ˚but-
ton and remove the CD.MP3 FILE PLAYBACK
Tracks jump during mp3 file play-
back
The CD is scratched or dirty. Clean the
CD, referring to what is described in the
“CD” paragraph in the “INTRODUC-
TION” chapter.
The duration of the mp3 tracks is not
shown correctly
In some cases (due to the recording
mode) the duration of the MP3 tracks may
be displayed incorrectly.
T T
R R
O O
U U
B B
L L
E E
S S
H H
O O
O O
T T
I I
N N
G G
603_97_285 Radio Punto FL GB 1ed 8-09-2009 9:55 Pagina 30