Bulb FIAT PUNTO EVO 2010 1.G Owners Manual
[x] Cancel search | Manufacturer: FIAT, Model Year: 2010, Model line: PUNTO EVO, Model: FIAT PUNTO EVO 2010 1.GPages: 270, PDF Size: 8.34 MB
Page 170 of 270
GENERIC INDICATOR
(amber)
(for versions/markets where provided)
The warning light turns on in the following cir-
cumstances:
Engine oil pressure sensor failure
The warning light turns on when a failure is detected in
the engine oil pressure sensor. Go to a Fiat Dealership to
have the fault fixed as soon as possible. The associated mes-
sage is displayed on some versions.
Start&Stop fault
(for versions/markets where provided)
The warning light comes on when a Start&Stop failure is de-
tected.
A specific message is displayed on certain versions.
169
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
REAR FOG LIGHTS (amber)
The light comes on when the rear fog lights are
turned on.
4
Fuel cut-off intervention
(for versions/markets, where provided)
The warning light comes on when the fuel cut-off system
intervenes (see “Multifunction display” in the “Controls”
section).
A specific message is displayed on certain versions.
Rain sensor fault
(for versions/markets where provided)
The warning light comes on when a rain sensor failure is
detected (see “Multifunction display” in the “Controls”
section). Contact a Fiat Dealership.
A specific message is displayed on certain versions.
Parking sensor fault
(for versions/markets where provided)
The warning light turns on when a failure is detected in
the parking sensors. In this case, contact a Fiat Dealership.
A specific message is displayed on certain versions.
Tyre pressure monitoring system (TPMS) failure
(for versions/markets where provided)
The warning light turns on when a failure is detected in
the TPMS system (for versions/markets where provided).
Contact a Fiat Dealership as soon as possible.
Should one or more wheels without a sensor be fitted, the
instrument panel warning light will come on and stay on
until the initial conditions are restored.
A specific message is displayed on certain versions.
è
The failure relating to these lights could be: one or more
blown bulbs, a blown protection fuse or a break in the elec-
trical connection. On certain versions warning light è
turns on as an alternative. On some versions the display
shows the associated message.
161-174 PUNTO FL EN 4ed 18-01-2010 12:27 Pagina 169
Page 187 of 270
CHANGING A BULB
GENERAL INSTRUCTIONS
❒When a light is not working, check that the corre-
sponding fuse is intact before changing the bulb. For the
location of fuses, refer to the “Changing a fuse” para-
graph in this section;
❒before changing a bulb check the contacts for rusting;
❒burnt bulbs must be replaced by others of the same type
and wattage;
❒for safety reasons, always check the direction of the
headlight beam after changing a bulb.
186
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
Halogen lamps must be handled holding
the metallic part only. Touching the trans-
parent part of the bulb with your fingers
may reduce the intensity of the light emitted and
even compromise the longevity of the bulb itself. In
the event of accidental contact, wipe the bulb with
an alcohol-soaked cloth and allow to dry.
Changes or repairs to the electrical system
(electronic control units) carried out in-
correctly and without due consideration for the
technical specifications of the system can lead to
malfunctioning and generate a fire hazard.
WARNING
Halogen lamps contain gas under pres-
sure. If they break, glass fragments could
fly everywhere.
WARNING
IMPORTANT The internal surface of the light may appear
slightly misty: this does not indicate a fault, and is actually
caused by low temperature and the degree of humidity
in the air. Misting will rapidly disappear when the head-
lights are switched on. The presence of drops inside the
headlights indicates infiltration of water. Go to a Fiat Deal-
ership.
TYPES OF BULBS
Various types of bulbs are fitted to your vehicle.
A Glass bulbs: pushed into position. Pull to extract.
B Bayonet-type bulbs: to remove from its holder, press
the bulb in and turn it anti-clockwise.
175-210 PUNTO FL EN 4ed 20-01-2010 15:09 Pagina 186
Page 188 of 270
187
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
C Tubular bulbs: release them from their contacts to
remove.
D-E Halogen bulbs: to remove the bulb, release the clip
holding the bulb in place.
fig. 164F0U0147m
175-210 PUNTO FL EN 4ed 20-01-2010 15:09 Pagina 187
Page 189 of 270
H4
H4
W5W
H11
PY21W
WY5W
P21W
LED
P21W
W2.3W
W16W
W16W
W5W
C10W
C10W
C10W
W5W
C5W D
D
A
–
B
A
B
–
B
B
–
–
A
C
C
C
A
C55 W
60 W
5 W
55 W
21 W
5 W
21 W
–
21 W
2.3 W
16 W
16 W
5 W
10 W
10 W
10 W
5 W
5 W
188
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
Bulbs Figure ref. Type Power
Main beams
Dipped beams
Front sidelights
Front fog lights (where provided)
Front direction indicators
Side direction indicators
Rear direction indicators
Taillights
Brake lights
Third brake light
Reverse lights
Rear fog lights
Number plate lights
Front ceiling light with movable lens
Front ceiling light with spot lights
Rear ceiling light
Boot light
Courtesy light
175-210 PUNTO FL EN 4ed 20-01-2010 15:09 Pagina 188
Page 190 of 270
D
C
AB
F0U0148mfig. 165F0U0149mfig. 166
IMPORTANT You can replace the front direction indica-
tor, main beam and dipped beam headlight bulbs through
the access flap (see “Direction indicators” in this section).
SIDELIGHTS fig. 166
To change the bulb, proceed as follows:
❒remove the rubber cap by pulling the flap;
❒press in tabs B and remove the bulb holder;
❒remove the bulb C and replace it;
❒refit the bulb holder and then refit the cap, ensuring that
it locks into place.
CHANGING AN EXTERIOR BULB
For the type of bulb and relative power rating, see “Chang-
ing a bulb”.
FRONT LIGHT CLUSTERS fig. 165
The front light clusters contain sidelights, dipped beam,
main beam and direction indicator bulbs.
The bulbs are arranged inside the light cluster as follows:
A sidelights
B daytime running lights
C direction indicators
D main beam/dipped beam headlights.
189
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
175-210 PUNTO FL EN 4ed 20-01-2010 15:09 Pagina 189
Page 191 of 270
190
F0U0250mfig. 167
DAYTIME RUNNING LIGHTS (DRL)
To change the bulb, proceed as follows:
❒turn the bulb holder A-fig. 167 anti-clockwise using the
tab and pull it out;
❒remove the bulb B by pushing it in slightly and turning
it anti-clockwise;
❒refit the bulb holder by putting it in its housing and turn-
ing it clockwise until it locks into place.
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
F0U0150mfig. 168
MAIN/DIPPED BEAM HEADLIGHTS
To change the bulb, proceed as follows:
❒remove the rubber cap;
❒disconnect the central electric connector B-fig. 168 and
release the bulb holder catch;
❒remove the bulb A and replace it;
❒fit the new bulb, aligning the outlines of the metallic part
with the grooves on the reflector;
❒refit the bulb holder catch and reconnect the electri-
cal connector;
❒refit the cap A, ensuring that it locks into place.
175-210 PUNTO FL EN 4ed 20-01-2010 15:09 Pagina 190
Page 192 of 270
191
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
F0U0152mfig. 170
A
A
B
F0U0151mfig. 169
DIRECTION INDICATORS
Front fig. 169
To change the bulb, proceed as follows:
❒steer the right/left wheel inwards;
❒turn the catch A-fig. 169, then lift off the access lid B;
D
F0U0153mfig. 171
❒remove the bulb holder cover C-fig. 170 by turning it
anti-clockwise;
❒remove the bulb D-fig. 171 by pushing it in gently and
turning anti-clockwise (“bayonet” clamping), then re-
place it;
❒refit the bulb holder cover C-fig. 170 by turning it clock-
wise and locking it properly;
❒close the lid B-fig.169 then tighten the catch A.
175-210 PUNTO FL EN 4ed 20-01-2010 15:09 Pagina 191
Page 193 of 270
192
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
A
F0U0526mfig. 173/b
❒loosen the fixing screws C and remove the headlamp;
❒remove the bulb A-fig.173/b by rotating it counter-
clockwise and disconnect the electrical connector.
F0U0280mfig. 172
Side fig. 172
To change the bulb, proceed as follows:
❒slide the lens A towards the front of the car to press
in the internal catch B, then pull the unit outwards;
❒turn the bulb holder C anti-clockwise, extract bulb D
and replace it;
❒refit the bulb holder C into the lens by turning it clock-
wise;
❒refit the unit making sure the internal catch B clicks in-
to place.
FRONT FOG LIGHTS
(for versions/markets where provided)
To replace the bulb:
❒loosen the screw A-fig.173/a and remove the protec-
tion template B;
C
AC
B
C
F0U0525mfig. 173/a
175-210 PUNTO FL EN 4ed 20-01-2010 15:09 Pagina 192
Page 194 of 270
193
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
REAR LIGHT CLUSTERS
The rear light clusters contain taillight, brake light and di-
rection indicator bulbs.
The bulbs are arranged inside the light cluster fig. 174 as
follows:
D direction indicators
E brake lights.
F0U0155mfig. 174F0U0156mfig. 175
To change the bulb proceed as follows:
❒undo both fastening bolts A-fig 174;
❒disconnect the central electric connector B and pull the
lens unit outwards;
❒ unhook the bulb holder by unclipping the fasteners
C-fig. 175;
❒remove the bulb by pushing it in gently and turning an-
ti-clockwise (“bayonet” clamping), then replace it;
175-210 PUNTO FL EN 4ed 20-01-2010 15:09 Pagina 193
Page 195 of 270
194
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
❒refit the bulb holder;
❒reconnect the electric connector, correctly realign the
unit with the car body and then tighten the fastening
screws A.
IMPORTANT To replace the LED taillights you must con-
tact a Fiat Dealership.
REAR FOG LIGHTS fig. 176
Contact a Fiat Dealership to have bulbs for the rear fog
lights A replaced.
REVERSE LIGHTS fig. 176
Contact a Fiat Dealership to have bulbs for the reverse
lights B replaced.
F0U0157mfig. 176F0U0281mfig. 177
THIRD BRAKE LIGHT fig. 177
To change the bulb proceed as follows:
❒open the boot;
❒remove the rubber caps;
❒press in the catches and remove the lens unit
C-fig. 177;
❒disconnect the electric connector;
❒press in the tabs D-fig. 177 and remove the bulb holder;
❒remove the snap-fitted bulb and replace it.
NUMBER PLATE LIGHTS
To change the bulb proceed as follows:
❒manipulate the point shown by the arrow and remove
the lens unit A-fig. 178;
175-210 PUNTO FL EN 4ed 20-01-2010 15:09 Pagina 194