ESP FIAT PUNTO EVO 2010 1.G Owners Manual
[x] Cancel search | Manufacturer: FIAT, Model Year: 2010, Model line: PUNTO EVO, Model: FIAT PUNTO EVO 2010 1.GPages: 270, PDF Size: 8.34 MB
Page 3 of 270
REFUELLING
Petrol engines: only refuel the car with unleaded
petrol with an octane rating (RON) of no less than 95
conforming to the European specification EN 228.
The use of petrol that does not conform to the above-
mentioned specification may cause the EOBD warning light
to switch on and the irregular operation of the engine.
Diesel engines: only refuel the car using diesel fuel that
conforms to European specification EN590.
STARTING THE ENGINE
Make sure that the handbrake is properly applied; place the
gear lever in neutral; fully depress the clutch pedal, with-
out pressing the accelerator, then turn the ignition key to
the MAR position and wait for the
Yand mwarning
lights to switch off (diesel versions); turn the ignition key to
the AVV position and release it as soon as the engine starts.
PARKING ON FLAMMABLE MATERIAL
The catalytic converter reaches high temperatures dur-
ing operation. Do not park the on grass, dry leaves, pine
needles or other flammable material: fire hazard.
RESPECTING THE ENVIRONMENT
The car is fitted with a system that carries out a con-
tinuous diagnosis of the emission-related components
in order to help protect the environment.ELECTRICAL ACCESSORIES
If, after buying the car, you decide to add electrical ac-
cessories (with the risk of gradually draining the bat-
tery), visit a Fiat Dealership. They can calculate the over-
all electrical requirement and check that the car’s elec-
trical system can support the required load.
CODE card
Keep this in a safe place, not in the car. You should have
the electronic code from the CODE card with you at
all times.
SCHEDULED SERVICING
Correct maintenance of the car is essential for ensuring it
stays in tip-top condition and safeguards its safety features,
its environmental friendliness and low running costs for
a long time to come.
THE OWNER’S HANDBOOK CONTAINS…
... information, tips and important warnings on the cor-
rect use and maintenance of your car over time as
well as safe driving tips. Pay special attention to the sym-
bols
"(personal safety) #(environmental protection)
!(the car’s wellbeing).
READ THIS CAREFULLY!
K
001-036 PUNTO FL EN 4ed 18-01-2010 12:21 Pagina 2
Page 8 of 270
7
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
F0U0005mfig. 5F0U0006mfig. 6
Replacing the battery of the key with remote
control fig. 6
To replace the battery, proceed as follows:
❒press button A and bring the metal insert B to the open
position;
❒turn the screw C to :using a fine screwdriver;
❒take out the battery case D and replace the battery E,
respecting its polarity;
❒refit the battery case D inside the key and lock it by
turning the screw C to
Á. Dashboard LED indications
When locking the doors, the LED A-fig. 5 in the button
switches on for about 3 seconds and then starts to flash
(as a deterrent).
Once doors are locked, if one or more doors or the boot
are not closed correctly, the LED and direction indicators
start flashing quickly.
001-036 PUNTO FL EN 4ed 18-01-2010 12:21 Pagina 7
Page 63 of 270
“FOLLOW ME HOME” DEVICE
This will light up the space in front of the vehicle for
a certain period of time.
Activation
With the key turned to STOP or removed, pull the left-
hand stalk towards the steering wheel within 2 minutes
from when the engine is turned off.
Each time the stalk is moved, the lights stay on for an ex-
tra 30 seconds up to a maximum of 210 seconds; then the
lights are switched off automatically.
The warning light
3on the instrument panel will light up
and the corresponding message will appear in the display
(see “Warning lights and messages”) for as long as the func-
tion is activated. The light comes on when the stalk is first
moved and stays on until the function is automatically de-
activated. Each movement of the stalk increases only the
amount of time the lights stay on.
Deactivation
Keep the stalk pulled towards the steering wheel for more
than 2 seconds.
fig. 50F0U0043m
62
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
DIRECTION INDICATORS fig. 50
Put the stalk in the permanent position:
up (position
1): activates the right direction indicator;
down (position
2): activates the left direction indicator.
Lights
¥or Îwill blink on the instrument panel. The in-
dicators switch off automatically when the steering wheel
is straightened.
Lane change function
If you wish to signal a lane change, put the left stalk in the
temporary position for less than half a second. The direc-
tion indicator on the selected side flashes three times and
then switches off automatically.
037-081 PUNTO FL EN 4ed 18-01-2010 12:23 Pagina 62
Page 68 of 270
67
INCREASING THE MEMORISED SPEED
This can be done in two ways:
❒by pressing the accelerator and then memorising the
new speed reached;
or
❒moving the stalk upwards (+).
Each movement of the stalk will correspond to an increase
in speed of about 1 km/h, while keeping the stalk held up-
wards will continuously increase the speed.
REDUCING THE MEMORISED SPEED
This can be done in two ways:
❒by turning the device off and then storing a new speed;
or
❒by moving the stalk downwards (–) until reaching the
new speed which will be memorised automatically.
Each movement of the stalk will correspond to a reduc-
tion in speed of about 1 km/h, while keeping the stalk held
downwards will continuously reduce the speed.
DISENGAGING THE DEVICE
The device can be switched off by the driver in the fol-
lowing ways:
❒turning twist switch A to OFF;
❒switching off the engine;
❒pressing the brake pedal;
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
❒pressing the clutch pedal;
❒pressing the accelerator pedal; in this case, the system
is not really switched off but the request for accelera-
tion takes priority. The cruise control is, however, ac-
tive and you do not need to press button RES B-fig. 52
to restore the previous conditions when you have fin-
ished accelerating.
The device is automatically switched off in the following
cases:
❒if the ABS or ESP systems cut in;
❒if the car speed drops below the preset limit;
❒if there is a system failure.
While travelling with the device engaged, do not
put the gear lever into neutral.
WARNING
In case of malfunctioning or if the device fails,
turn twist switch A to OFF and contact a Fiat
Dealership.
WARNING
037-081 PUNTO FL EN 4ed 18-01-2010 12:23 Pagina 67
Page 77 of 270
76
F0U0065mfig. 70
FRONT ARMREST WITH STORAGE
COMPARTMENT
(for versions/markets where provided)
Certain versions are fitted with an armrest A-fig. 69 be-
tween the front seats.KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
F0U0063mfig. 71
To bring this to the standard position of use, push it down
as shown in fig. 69.
Press button A-fig. 70 to raise the top of the armrest in
order to use storage compartment B. Use lever C to tilt
down the armrest with respect to its normal position.
DOOR POCKETS fig. 71
There are document/map pockets and a bottle holder
built into each of the door panels.
F0U0064mfig. 69
037-081 PUNTO FL EN 4ed 18-01-2010 12:23 Pagina 76
Page 91 of 270
90
F0U0084mfig. 92
Front passenger-side and rear doors
(for versions/markets where provided)
The front passenger door armrest and rear door armrests
feature switches A-fig. 92 for controlling the correspond-
ing window.
Press button A-fig. 93 to disable the controls located on
the rear doors (for versions/markets where provided). IMPORTANT In the event that the anti-crushing function
is activated 5 times in only 1 minute, the system will au-
tomatically enter the “recovery” mode (self-protection).
This condition is apparent from the window closing in
stages.
On such occasions, it is necessary to carry out the system
restore procedure, acting as follows:
❒open the windows;
or
❒turn the ignition key to STOP and then to MAR.
If no malfunction is present, the window returns to its nor-
mal operation automatically.
IMPORTANT With the ignition key at STOP or removed,
the windows remain activated for about 2 minutes and are
deactivated as soon a door is opened.KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
The system conforms to the 2000/4/EC
standard concerning the safety of passen-
gers leaning out of the passenger compartment.
WARNING
IMPORTANTOn some versions, pressing the remote con-
trol button Ëfor over 2 seconds will open the windows,
whereas pressing the remote control button Áfor over
2 seconds will close them.
082-128 PUNTO FL EN 4ed 20-01-2010 15:06 Pagina 90
Page 104 of 270
103
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
SYSTEM INTERVENTION
The driver can tell the ABS system has come into action
because the brake pedal pulsates slightly and the system
gets noisier: it means that the vehicle speed should be al-
tered to suit the type of road surface.ABS SYSTEM
If you have never driven a vehicle with ABS before, it is ad-
visable to perform a few tests on slippery ground, always
in safe conditions and respecting the highway code of the
country where you are driving. Read the following infor-
mation carefully.
This system, which is an integral part of the braking sys-
tem, prevents one or more wheels from locking and skid-
ding on all road surface conditions, irrespective of the in-
tensity of the braking action, ensuring that the vehicle can
be controlled even during emergency braking.
The system is completed by EBD (Electronic Braking Force
Distribution), which distributes the braking action between
the front and rear wheels.
IMPORTANT For the maximum efficiency of the braking
system, a bedding-in period of about 500 km is needed (for
a new vehicle or after having replaced the brake
pads/discs): during this period it is better to avoid sharp,
repeated and prolonged braking.
The ABS system gets the most out of the
available grip but it cannot improve it.
Therefore, you should take great care when
driving on slippery surfaces: don’t take unneces-
sary risks.
WARNING
If the ABS cuts in, it is a sign that the grip
between tyre and the road surface has
reached the limit: you must slow down to match
the speed to the road grip available.
WARNING
FAILURE INDICATIONS
ABS failure
ABS failure is indicated by warning light >coming on on
the instrument panel together with the dedicated message
on the multifunction display (where provided), (see “Warn-
ing lights and messages”).
In this case, the braking system will work as normal, but
without the extra capacity offered by the ABS system. Dri-
ve carefully to the nearest Fiat Dealership to have the sys-
tem checked.
EBD failure
EBD failure is indicated by warning lights >and xcom-
ing on on the instrument panel together with the dedicated
message on the multifunction display (where provided),
(see section “Warning lights and messages”).
082-128 PUNTO FL EN 4ed 20-01-2010 15:06 Pagina 103
Page 105 of 270
BRAKE ASSIST
(integrated ESP emergency braking assistance)
(for versions/markets where available)
This system (which cannot be switched off) recognises
emergency braking (according to the speed of operation
of the brake pedal) and provides additional hydraulic brak-
ing pressure to support that applied by the driver. This
allows faster and more powerful operation of the brak-
ing system.
The Brake Assist is deactivated on versions equipped with
ESP if there is an ESP system failure (indicated by the warn-
ing light and the message on the multifunction display, for
versions/markets where provided). Drive carefully to the nearest Fiat Dealership to have the
system checked.
104
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTSIf only warning light xlights up on the in-
strument panel (with a message on the
multifunction display, where provided), stop the
car immediately and contact the nearest Fiat
Dealership. Fluid leaking from the hydraulic sys-
tem will compromise the operation of the brak-
ing system, whether it is of the conventional type
or with ABS.
WARNING
When the ABS cuts in, and you feel the
brake pedal pulsating, do not remove your
foot, but keep it pressed; in doing so you will stop
in the shortest distance possible under the road
conditions at the time.
WARNING
082-128 PUNTO FL EN 4ed 20-01-2010 15:06 Pagina 104
Page 106 of 270
105
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
SYSTEM ACTIVATION
The ESP system comes on automatically when the vehi-
cle is started and cannot be turned off.
FAILURE INDICATIONS
In the event of a failure, the ESP will be automatically
switched off and the áwarning light will come on per-
manently on the instrument panel along with a message on
the multifunction display (for versions/markets where pro-
vided) (see “Warning lights and messages” section). The
LED on the ASR OFF button will also light up. Contact a
Fiat Dealership as soon as possible if this happens.ESP SYSTEM
(Electronic Stability Program)
(for versions/markets where provided)
This is an electronic system that controls car stability in
the event of tyre grip loss, helping to maintain direction-
al control.
The ESP system is therefore particularly useful when the
grip conditions of road surfaces change.
The MSR system (adjustment of the engine braking torque
during gear changes) and the HBA system (automatic in-
crease in the braking pressure during emergency brak-
ing) are present with ESP, ASR and Hill Holder systems
(for versions/markets where provided).
SYSTEM INTERVENTION
This is signalled by warning light áflashing on the instru-
ment panel to inform the driver that the car is experiencing
critical stability and grip conditions.
082-128 PUNTO FL EN 4ed 20-01-2010 15:06 Pagina 105
Page 107 of 270
106
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
Do not take unnecessary risks, even if your
vehicle is fitted with an ESP system. Your
driving style must always be suited to the road
conditions, visibility and traffic. The driver is al-
ways ultimately responsible for road safety.
WARNING
HILL HOLDER SYSTEM
This system is an integral part of the ESP system and it
facilitates hill starts.
It is automatically activated in the following conditions:
❒uphill: vehicle stationary on a road with a gradient high-
er than 5%, engine running, brake pedal pressed and
gearbox in neutral or gear other than reverse;
❒downhill: vehicle stationary on a road with a gradient
higher than 5%, engine running, brake pedal pressed and
reverse gear engaged.During start-up, the ESP system control unit maintains the
braking pressure at the wheels until the engine torque
required for departure is reached, or for a maximum of
1 second, allowing your right foot to be moved easily from
the brake pedal to the accelerator.
If the vehicle has not departed after this time, the system
will deactivate automatically by gradually releasing the
brake force.
At release, the typical brake disengagement noise indicat-
ing that the car is going to move will be heard.
082-128 PUNTO FL EN 4ed 20-01-2010 15:06 Pagina 106