gas type FIAT PUNTO EVO 2010 1.G Owners Manual
[x] Cancel search | Manufacturer: FIAT, Model Year: 2010, Model line: PUNTO EVO, Model: FIAT PUNTO EVO 2010 1.GPages: 270, PDF Size: 8.34 MB
Page 129 of 270
128
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
DIESEL PARTICULATE FILTER (DPF)
(for versions/markets where provided)
The Diesel Particulate Filter is a mechanical filter, inte-
gral to the exhaust system, that physically traps particu-
lates present in the exhaust gases of diesel engines.
It is needed to eliminate almost all particulates in compli-
ance with current/future legislation.
During normal use of the vehicle, the engine control unit
records a set of data (e.g. travel time, type of route, tem-
peratures, etc.) and it will then calculate how much par-
ticulate has been trapped by the filter.
Since this filter physically traps particulate, it should be re-
generated (cleaned) at regular intervals by burning the car-
bon particles.
The regeneration procedure is handled automatically by
the engine control unit according to the filter conditions
and vehicle use conditions.
During regeneration, the following may occur: a limited in-
crease in the engine speed, activation of the fan, a limited
increase in fumes and high temperatures at the exhaust.
These are not faults; they do not impair vehicle perfor-
mance or damage the environment.
If the dedicated message is displayed, refer to the “Warn-
ing lights and messages” section.
The diesel particulate filter (DPF) (for ver-
sions/markets where required) reaches
high temperatures during normal operation.
Therefore do not therefore park the vehicle on in-
flammable materials (grass, dry leaves, pine nee-
dles, etc.): fire hazard.
WARNING
The catalytic converter also reaches high
temperatures during normal operation.
Do not park the vehicle on grass, dry leaves, pine
needles or other flammable material: fire hazard.
WARNING
082-128 PUNTO FL EN 4ed 20-01-2010 15:07 Pagina 128
Page 159 of 270
158
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
Assembly diagram fig. 149
The tow hook structure must be fas-
tened at the points marked by
Øus-
ing a total of 6 M10 screws.
The internal back plates should be at
least 6 mm thick.
The hook should be fastened to the
body avoiding any type of drilling of
the rear bumper that remains visible
when the hook is removed.
IMPORTANT It is compulsory to at-
tach a label (plainly visible) of suitable
size and material at the same level as
the hitch ball, with the following
wording:
MAX LOAD ON BALL 60 kg
After assembly, the screw
holes should be sealed to
prevent exhaust gases getting in.
WARNING
fig. 149F0U0132m
Existing
hole
Existing
screw
Existing screw
Existing
holeExisting
hole
Existing hole
Standard ball
Laden
149-160 PUNTO FL EN 4ed 20-01-2010 14:37 Pagina 158
Page 187 of 270
CHANGING A BULB
GENERAL INSTRUCTIONS
❒When a light is not working, check that the corre-
sponding fuse is intact before changing the bulb. For the
location of fuses, refer to the “Changing a fuse” para-
graph in this section;
❒before changing a bulb check the contacts for rusting;
❒burnt bulbs must be replaced by others of the same type
and wattage;
❒for safety reasons, always check the direction of the
headlight beam after changing a bulb.
186
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
Halogen lamps must be handled holding
the metallic part only. Touching the trans-
parent part of the bulb with your fingers
may reduce the intensity of the light emitted and
even compromise the longevity of the bulb itself. In
the event of accidental contact, wipe the bulb with
an alcohol-soaked cloth and allow to dry.
Changes or repairs to the electrical system
(electronic control units) carried out in-
correctly and without due consideration for the
technical specifications of the system can lead to
malfunctioning and generate a fire hazard.
WARNING
Halogen lamps contain gas under pres-
sure. If they break, glass fragments could
fly everywhere.
WARNING
IMPORTANT The internal surface of the light may appear
slightly misty: this does not indicate a fault, and is actually
caused by low temperature and the degree of humidity
in the air. Misting will rapidly disappear when the head-
lights are switched on. The presence of drops inside the
headlights indicates infiltration of water. Go to a Fiat Deal-
ership.
TYPES OF BULBS
Various types of bulbs are fitted to your vehicle.
A Glass bulbs: pushed into position. Pull to extract.
B Bayonet-type bulbs: to remove from its holder, press
the bulb in and turn it anti-clockwise.
175-210 PUNTO FL EN 4ed 20-01-2010 15:09 Pagina 186
Page 218 of 270
217
CHECKING LEVELSKNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
fig. 198 – 1.2 and 1.4 8vversions
fig. 199 – 1.4 Multi Air versions
Never smoke while
working in the engine
compartment: inflammable gas-
es and vapours may be present,
constituting a fire risk.
WARNING
When topping up, take
care not to mix up the
various types of fluids:
they are not compatible with
each other and could seriously
damage the car.
1. Engine coolant
2. Battery
3. Windscreen washer fluid
4. Brake fluid
5. Engine oil.
F0U0181m
F0U0182m
211-234 PUNTO FL EN 4ed 18-01-2010 12:27 Pagina 217