reset FIAT PUNTO EVO 2010 1.G Owners Manual
[x] Cancel search | Manufacturer: FIAT, Model Year: 2010, Model line: PUNTO EVO, Model: FIAT PUNTO EVO 2010 1.GPages: 270, PDF Size: 8.34 MB
Page 7 of 270
6
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
F0U0004mfig. 4
KEY WITH REMOTE CONTROL fig. 4
The metal insert A operates:
❒the ignition;
❒the door locks;
❒the fuel cap lock/release (for versions/markets where
provided);
Pressing button B opens/closes the metal insert.
All the keys and the CODE card must be
handed over to the new owner when selling
the car.
Only press button B with the key away
from your body, specifically from your
eyes and from objects which could get damaged
(e.g. your clothes). Do not leave the key unat-
tended to avoid the button being accidentally
pressed while it is being handled, e.g. by a child.
WARNING
Button Ëis used for unlocking the doors and the boot.
Button Áis used for locking the doors and the boot.
Button
Ris used to open the boot remotely.
When unlocking the doors, the passenger compartment
ceiling lights will come on for a preset time.
001-036 PUNTO FL EN 4ed 18-01-2010 12:21 Pagina 6
Page 36 of 270
35
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
BUTTON VOLUME
(Adjusting the button volume)
This function may be used to adjust (over 8 levels) the vol-
ume of the noise made when the MENU ESC, +e –but-
tons are pressed.
To set the desired volume, proceed as follows:
– briefly press MENU ESC: the previously set volume lev-
el will flash on the display;
– press +or –to set the value;
– briefly press the MENU ESC button to go back to the
menu screen or hold the button down to go back to the
standard screen without saving.
SEAT BELT BUZZ
(SBR buzzer reactivation
(for versions/markets where provided)
This function can be displayed only after a Fiat Dealer-
ship has deactivated the SBR system (see “SBR system”
in the “Safety” section).SERVICE
(Scheduled servicing)
Through this function it is possible to display information
related to regular scheduling intervals.
This information can be consulted as follows:
– briefly press MENU ESC: service intervals in km or mi,
depending on the previous setting, will be displayed (see
“Measurement units”);
– press the MENU ESC button briefly to return to the
menu screen or hold the button down to return to the
standard screen.
NBThe “Scheduled Servicing Plan” requires the vehicle
to be serviced every 30,000 km (or 18,000 mi). This indi-
cation will appear automatically, with the key at MAR, start-
ing from 2,000 km (or 1,240 mi) and will be displayed every
200 km (or 124 mi). Below 200 km the signals become
more frequent. The indication will appear in kilometres or
miles depending on the unit of measurement settings.
When the next scheduled service is approaching, the mes-
sage “Service” will appear on the display, followed by the
number of kilometres or miles left, when the key is turned
to MAR. Go to a Fiat Dealership, where the “Scheduled
Servicing Plan” operations will be performed and the mes-
sage will be reset.
001-036 PUNTO FL EN 4ed 18-01-2010 12:22 Pagina 35
Page 38 of 270
37
Values displayed
Outside temperature
Indicates the temperature outside the vehicle passenger
compartment.
Range
This indicates the approximate distance that may be trav-
elled with the fuel remaining in the tank, assuming that dri-
ving conditions do not change. The display will show the
reading “----” when the following events take place:
– value lower than 50 km (or 30 mi)
– car left parked with engine running for a long time.
Distance travelled
This value shows the distance covered from the start of
the new journey.
Average consumption
This value shows the approximate average fuel consump-
tion from the start of the new journey.
Current consumption
Indicates the fuel consumption. The value is constantly up-
dated. The message “----” will appear on the display if the
car is parked with the engine running.
Average speed
This value shows the car’s average speed based on the
overall time elapsed since the start of the new journey.TRIP COMPUTER
Introduction
The Trip computer is used to display information on car
operation when the key is turned to MAR. This function
allows you to define two separate trips, called “Trip A”
and “Trip B”, for monitoring the car’s “complete mission”
(journey) in a reciprocally independent manner.
Both functions can be reset (reset – start of a new jour-
ney).
“Trip A” is used to display the figures relating to:
– Outside temperature
– Range
– Distance travelled
– Average consumption
– Current consumption
– Average speed
– Journey time (driving time).
“Trip B”, available on multifunction display only, is used to
display the figures relating to:
– Distance travelled B
– Average consumption B
– Average speed B
– Travel time B (driving time).
NB“Trip B” functions may be excluded (see “Trip B on”).
“Range” and “Instant consumption” parameters cannot be
reset.
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
037-081 PUNTO FL EN 4ed 18-01-2010 12:23 Pagina 37
Page 39 of 270
38
F0U0022mfig. 28
New journey
The new journey begins after:
– “manual” resetting by the user, by pressing the relevant
button;
– “automatic” resetting, when the distance travelled reach-
es 99,999.9 km or when the journey time reaches 99.59
(99 hours and 59 minutes);
– disconnection and subsequent reconnection of the bat-
tery.
IMPORTANT The reset operation when “Trip A” details
are being displayed resets only the information associat-
ed with this function.
IMPORTANT The reset operation when “Trip B” details
are being displayed resets only the information associat-
ed with this function.
Start trip procedure
With the ignition key in the MAR position, reset by press-
ing the TRIP button and keeping it pressed for more than
2 seconds.
Trip Exit
To quit the Trip function: keep MENU ESC pressed for
over 2 seconds. Journey time
This value shows the time elapsed since the start of the
new journey.
IMPORTANT If information is not available, the message
“----” will appear instead of the Trip Computer values.
Counting of the different values will resume regularly when
normal operation is restored. This will not reset any of the
values displayed before the failure nor start a new jour-
ney.
TRIP control button fig. 28
The TRIP button, located on the top of the right steering
column stalk, is used (with ignition at MAR) to display and
reset the previous values to start a new journey:
– press briefly to display the different values;
– hold down to reset and then start a new journey.KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
037-081 PUNTO FL EN 4ed 18-01-2010 12:23 Pagina 38
Page 67 of 270
❒move the stalk upwards (+) for at least one second, then
release it. The car speed is now memorised and you can
therefore come off the accelerator pedal.
If needed (when overtaking for instance), you can accel-
erate simply by pressing the accelerator pedal; when you
come off the pedal, the car will return to the speed mem-
orised previously.
RESTORING THE MEMORISED SPEED
If the device has been switched off, for example by press-
ing the brake or clutch pedal, the memorised speed can
be restored as follows:
❒accelerate gradually until reaching a speed approaching
the memorised speed;
❒engage the gear that was selected when you memorised
the speed;
❒press button RES B-fig. 52.
66
CRUISE CONTROL
(for versions/markets where provided)
This is an electronically controlled device which allows the
vehicle to be driven at a chosen speed above 30 km/h on
long stretches of dry, straight roads with few variations (e.g.
motorways), without having to press the accelerator ped-
al. It is therefore not recommended to use this device on
country roads with traffic. Do not use it in town.
ENGAGING THE DEVICE
Turn twist switch A-fig. 52 to ON.
The cruise control cannot be engaged in 1st or reverse
gear. It is advisable to engage it in 4th gear or higher.
When travelling downhill with the device engaged, the car
speed may slightly exceed the preset one.
When the device is activated, light
Ücomes on together
with the relevant message on the instrument panel (where
provided).
SETTING VEHICLE SPEED
Proceed as follows:
❒turn twist switch A-fig. 52 to ON and press the accel-
erator pedal until you reach the required speed;
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
F0U0047mfig. 52
037-081 PUNTO FL EN 4ed 18-01-2010 12:23 Pagina 66
Page 68 of 270
67
INCREASING THE MEMORISED SPEED
This can be done in two ways:
❒by pressing the accelerator and then memorising the
new speed reached;
or
❒moving the stalk upwards (+).
Each movement of the stalk will correspond to an increase
in speed of about 1 km/h, while keeping the stalk held up-
wards will continuously increase the speed.
REDUCING THE MEMORISED SPEED
This can be done in two ways:
❒by turning the device off and then storing a new speed;
or
❒by moving the stalk downwards (–) until reaching the
new speed which will be memorised automatically.
Each movement of the stalk will correspond to a reduc-
tion in speed of about 1 km/h, while keeping the stalk held
downwards will continuously reduce the speed.
DISENGAGING THE DEVICE
The device can be switched off by the driver in the fol-
lowing ways:
❒turning twist switch A to OFF;
❒switching off the engine;
❒pressing the brake pedal;
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
❒pressing the clutch pedal;
❒pressing the accelerator pedal; in this case, the system
is not really switched off but the request for accelera-
tion takes priority. The cruise control is, however, ac-
tive and you do not need to press button RES B-fig. 52
to restore the previous conditions when you have fin-
ished accelerating.
The device is automatically switched off in the following
cases:
❒if the ABS or ESP systems cut in;
❒if the car speed drops below the preset limit;
❒if there is a system failure.
While travelling with the device engaged, do not
put the gear lever into neutral.
WARNING
In case of malfunctioning or if the device fails,
turn twist switch A to OFF and contact a Fiat
Dealership.
WARNING
037-081 PUNTO FL EN 4ed 18-01-2010 12:23 Pagina 67
Page 124 of 270
123
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
F0U0109mfig. 126
SOUND SYSTEM
(for versions/markets where provided)
For the operation of the radio with CD/MP3 player (where
provided), read the Supplement attached to this Owner
Handbook.
SOUND SYSTEM CAPABILITY
(for versions/markets where provided)
The system consists of:
❒sound system power cables;
❒front and rear speaker connecting wires;
❒aerial power cable;
❒2 tweeters on front doors (30W max power each);❒2 mid-woofers on front doors (165 mm diameter, 40W
max power each);
❒2 full-range speakers on rear doors and rear valance
panels (130 mm diameter, 40W max power each);
❒radio aerial wire;
❒aerial.
Sound system installation
The sound system must be installed in the place occupied
by the central oddments compartment, where you will find
the wiring.
To extract the compartment, press in the points shown in
the diagram corresponding to the retainer systems.
For connection to the preset cables, con-
tact a Fiat Dealership to prevent any prob-
lem that could impair car safety.
WARNING
082-128 PUNTO FL EN 4ed 20-01-2010 15:07 Pagina 123
Page 125 of 270
CD CHANGER CAPABILITY
(for versions/markets where provided)
The system consists of:
❒power cables
❒connection cables.
124
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
For connection to the preset cables, con-
tact a Fiat Dealership to prevent any prob-
lem that could impair car safety.
WARNING
F0U0110mfig. 127
SATELLITE NAVIGATION SYSTEM
CAPABILITY
(for versions/markets where available)
On cars equipped with the Blue&Me
™system, there may
be (on request) capacity to install the Blue&Me
™Tom-
Tom®satellite navigation system, which is available from
Lineaccessori Fiat.
Install the navigation system by inserting the specific sup-
port bracket into the housing shown in fig. 127.
082-128 PUNTO FL EN 4ed 20-01-2010 15:07 Pagina 124
Page 158 of 270
157
An electric brake or winch should be powered directly by
the battery through a cable with a cross-section of no less
than 2.5 mm
2.
IMPORTANT The engine must be running to use the elec-
tric brake or winch.
In addition to the electrical branches, the vehicle’s elec-
trical system can be connected only to the supply cable for
an electric brake and to the cable for an internal trailer
light, though not above 15W.
For connections, use the preset control unit with a bat-
tery cable no less than 2.5 mm
2.
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
INSTALLING THE TOW HOOK
The towing device should be fastened to the body by spe-
cialised personnel in accordance with any additional infor-
mation supplied by the manufacturer of the device.
The towing device must meet current regulations with ref-
erence to Directive 94/20/EC and subsequent amendments.
For any version, the towing device used must be right for
the towable weight of the car on which it is to be installed.
For the electric connection a unified connector should be
used, which is generally placed on a special bracket fastened
to the towing device, and a special ECU should be installed
on the car to control the trailer’s exterior lights. 7 or 13-
pin 12VDC connections should be used (CUNA/UNI and
ISO/DIN Standards). Follow any instructions provided by
the car manufacturer and/or the towing device manufac-
turer.
149-160 PUNTO FL EN 4ed 20-01-2010 14:37 Pagina 157
Page 168 of 270
167
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
FUEL RESERVE (amber)
Turning the key to the MAR position illuminates
the warning light, but it will switch off after a few
seconds.
The warning light turns on when about 7 litres of fuel are
left in the tank.
IMPORTANT The warning light will blink to indicate a sys-
tem failure. If this happens, go to a Fiat Dealership to have
the system checked.
Warning light “indicates a failure of warn-
ing light ¬. This condition is indicated by
intermittent blinking of warning light “for longer
than 4 seconds. In this case, warning light ¬may
not be indicating that there is a fault in the restraint
systems. Before driving off, contact a Fiat Dealer-
ship to have the system checked immediately.
WARNING
ç
ABS SYSTEM FAULT (amber)
Turning the key to the MAR position illuminates
the warning light, but it will switch off after a few
seconds.
The warning light comes on when the system is either not
working properly or not available. Under these circum-
stances, the braking system will work as normal but without
the extra performance offered by the ABS system. Drive
carefully and go to a Fiat Dealership as soon as possible.
On some versions the display shows the associated message.
>
GLOW PLUG PREHEATING
(Multijet versions – amber)
GLOW PLUG PREHEATING FAULT
(Multijet versions – amber)
Glow plugs
This warning light comes on when the key is turned to
MAR. It will go out as soon as the glow plugs have reached
a preset temperature. Start the engine as soon as the
warning light goes out.
IMPORTANT When it is particularly warm outside, the
warning light stays on for an extremely short time.
Glow plug preheating fault
The warning light flashes if there is a fault in the preheat-
ing system. Go to a Fiat Dealership as soon as possible.
A specific message is displayed on certain versions.
m
161-174 PUNTO FL EN 4ed 18-01-2010 12:27 Pagina 167