cooling FIAT ULYSSE 2007 2.G Owners Manual
[x] Cancel search | Manufacturer: FIAT, Model Year: 2007, Model line: ULYSSE, Model: FIAT ULYSSE 2007 2.GPages: 254, PDF Size: 3.42 MB
Page 68 of 254
GETTING TO KNOW YOUR CAR
67
CLIMATE CONTROL (cooling)
Proceed as follows:
- turn the slider pointer Bto the blue
section;
- press button Fto turn the climate
control compressor on and button G
to turn on inside air recirculation;
- turn the slider pointer Ato the re-
quired speed.
• fan speed setting: this is possi-
ble by turning slider A.
• air distribution selection: this is
possible by this is possible by turning
slider E.
Air can be distributed in five
ways: ventilation (front), bilevel
(front/feet), feet, windscreen/feet,
windscreen (MAX-DEF).
• compressor on/off: if the com-
pressor is turned off by pressing but-
ton Nwhen the led is lit, the related
led will go off; if the same button is
pressed when the led is switched off,
the compressor (on/off) is on.• MAX-DEF on: this is possible by
pressing button Dand window
demisting will be quickly reached.
• rear heated window on: this is
possible by pressing button C, and the
related led comes on. In this way the
rear window electrical resistances are
activated to heat and demist the rear
window. To stop it, press the button
again and the related led will go off.
Anyway, the rear heated window
works for a limited time and turns off
automatically.Be careful not to dam-
age the rear heated win-
dow resistances when
cleaning it from inside.
• recirculation on: when button G
is pressed it is possible to select the
following travelling conditions: closed
recirculation (relative led on), air com-
ing from outside (led off) recirculation
open, or having the system automatic
control on (led off even if activated).
Page 152 of 254
DRIVING YOUR CAR
151
STORING THE CAR
The following precautions should be
taken if the car will not be used for
several months:
– park the vehicle in covered, dry and
if possible well-ventilated premises;
– engage a gear (Pfor versions with
automatic electronic gear);
– make sure the handbrake is not en-
gaged;
– clean and protect the painted parts
using protective wax;
– sprinkle talcum powder on the rub-
ber windscreen and rear window
wiper blades and lift them off the glass;
– slightly open the windows;
– inflate the tyres to 0.5 bar above
the normal specified pressure and
check it at intervals;– switch off the electronic car alarm;
– disconnect the terminals (–) from
the battery poles (negative pole first)
and check the battery charge. When
the vehicle is in storage, this check
should be carried out once a month.
If no-load voltage is less than 12.5V,
recharge the battery;
– do not drain the engine cooling sys-
tem;
– cover the vehicle with a cloth or
perforated plastic sheet. Do not use
sheets of non-perforated plastic as
they do not allow moisture on the car
body to evaporate.RESTARTING THE CAR
AFTER STORAGE
Before restarting the vehicle after a
long storage, make the following op-
erations:
– do not take dust off the bodywork
without water;
– check if there are fluid leakages (oil,
brake and clutch fluid, engine coolant,
etc.);
– have the engine oil and the filter re-
placed;
– check the level of: brake and clutch
fluid, engine coolant;
Page 195 of 254
CAR MAINTENANCE
194
Do not remove the
reservoir cap when the
engine is hot: you risk
scalding yourself. ENGINE COOLANT fig. 5-6Check coolant level when the engine
is cold. The level should be included
between the MINand MAXrefer-
ence line on the reservoir.If the level is low, loosen the header
tank cap Aand slowly pour a mixture
of the fluid specified in the ”Lubricant
and fluid specifications” table in sec-
tion “Technical Specifications”,
through the filler neck until nearing the
MAXmark.
The antifreeze mixture contained in
the cooling circuit guarantees protec-
tion down to –40°C.
fig. 5 - Versions 2.0 JTD 120 HP - 136 HP
F0B0444b
fig. 6 - Versions 2.2 JTD
F0B0602b
Page 196 of 254
Top up only with the
same fluid contained in
the cooling circuit.
PARAFLU UP (red) cannot be
mixed with PARAFLU 11 (blue)
or with other fluids. Should this
take place, do not start the en-
gine and contact Fiat Dealership.
CAR MAINTENANCE
195
WINDSCREEN - REAR
WINDOW - HEADLIGHT
WASHER FLUID (where fitted)
fig. 7-8
Remove cap Aand check the fluid
level.
If it is necessary to top up the fluid,
pour in a mixture of water and
TUTELA PROFESSIONAL SC 35
fluid in the following proportions:
– 30% of TUTELA PROFES-
SIONAL SC 35and 70% of water in
summer; The cooling system is
pressurised. If necessary,
replace the cap only with
another genuine one, otherwise
system efficiency could be com-
promised.– 50% of TUTELA PROFES-
SIONAL SC 35and 50% of water in
winter;
– use undiluted TUTELA PRO-
FESSIONAL SC 35for tempera-
tures below –20°C.
fig. 7 - Versions 2.0 JTD 120 HP - 136 HP
F0B0445b
fig. 8 - Versions 2.2 JTD
F0B0603b
Page 230 of 254
TECHNICAL SPECIFICATIONS
229
CAPACITIES
2.0 JTD
120 HP
litres
80
8
9
5.25
1.9
–
1.2
1.2
0.519
7.52.0 JTD
136 HP
litres
80
8
9
5.25
1.9
–
1.2
1.2
0.519
7.5Recommended fluids
and lubricants
Recommended products
Diesel for motor vehicles
(EN590 specifications)
Mixture of distilled water and
PARAFLU11(blue) at 50% or
PARAFLU UP(red) at 50%
SELENIA TURBO DIESEL (❏)
TUTELA MATRYX
TUTELA GI/E
TUTELA GI/A
TUTELA GI/R
TUTELA TOP 4
50-50 mixture of distilled
water and TUTELA
PROFESSIONAL SC 35 2.2 JTD
170 HP
litres
80
8
9
4.75
–
–
1.2
1.2
0.93
7.5
Fuel tank:
– including a reserve of:
Engine cooling system:
Engine sump and filter:
Transaxle:
Automatic gearbox
Hydraulic power steering:
Electro-hydraulic power steering
Hydraulic brake circuit with:
ABS (with ESP)
Windscreen, rear mirror and headlight
liquid reservoir:
(❏) For temperatures lower than –15°C we recommend using SELENIA WR DIESEL SAE5W-40.
Page 232 of 254
TECHNICAL SPECIFICATIONS
231
(*) IMPORTANTDo not add or mix with fluids with specifications other than the specified ones. Use
Drive lubricants
and grease
Brake fluid
Radiator
antifreeze
Windscreen /
rear window/
headlight washer fluidFluid and lubricant specifications
for correct car operation
Synthetic oil SAE 75W-85 complying with API GL4 and
MIL-L-2105 D LEV specifications
ATF DEXRON II D oil, LEV
Synthetic fluid for hydraulic and electro-hydraulic systems
ATF DEXRON III oil
Molybdenum disulphide grease high temperature resistant
specific for homocinetic joints, NLGI 1-2consistency.
Synthetic fluid, F.M.V.S.S. n° 116, DOT 4, ISO 4925,
SAE J-1704, CUNA NC 956-01
Protective with antifreeze action, blue color, based on inhibit-
ed monoethylene glycol, CUNA NC 956-16
Protective with antifreeze action, red colour, based on inhibited
monoethylen glycol, with O.A.T.-based organic formula,
that passes CUNA NC 956-16, ASTM D 3306 specifications
Mixture of alcohol, water and surfactants CUNA NC 956-11Recommended
fluids and lubricants
TUTELA
MATRYX
TUTELA GI/A
TUTELA GI/R
TUTELA GI/E
TUTELA
ALL STAR
TUTELA TOP 4
PARAFLU 11 (*)
or
PARAFLU UP (*)
TUTELA
PROFESSIONAL
SC 35Applications
Mechanical gearbox
and differential
Hydraulic power
steering
Electro Hydraulic power
steering
Electronic
automatic gearbox
CV joints
Hydraulic brakes
and clutch
Cooling ducts
Percentage:
50% down to –35°C
To be used diluted
or neat in windscreen
washer/wiper systems