remove seats FIAT ULYSSE 2007 2.G Owners Manual

GETTING TO KNOW YOUR CAR
24
Once you have released
the lever, check that the
seat is firmly locked in the
runners by trying to move it back
and forth. Failure to lock the seat
in place could result in the seat
moving suddenly and the driver
losing control of the car.TO ADJUST THE RECLINING
SEAT BACK fig. 24
Pull out the lever Ato its full extent
and move it up or down to get the re-
quired position, then release it.
HEIGHT ADJUSTMENT
(DRIVER’S SEAT) fig. 24
To lift the seat, pull out the lever B
to its full extent and move it up or
down to get the required position. To
lower the seat, pull down the lever B
and move it up or down to get the re-
quired position.IMPORTANTThe adjustment can
only be made sitting in the driving
seat. Do not remove the seats or car-
ry out maintenance and/or repairs on
them: any operations that are not car-
ried out properly may affect the safe-
ty devices; always take your vehicle to
a Fiat Dealership.
LUMBAR ADJUSTMENT
(WHERE FITTED) fig. 25
That provides better support for the
back. Turn knob Ato make the ad-
justment.
FRONT SEATS
MOVING THE SEAT
BACKWARDS
OR FORWARDS fig. 23
Lift lever Aand push the seat back-
wards or forwards.
fig. 23
F0B0015b
fig. 24
F0B0188b
fig. 22
F0B0016b

GETTING TO KNOW YOUR CAR
29
DISMANTLING THE SECOND
AND THIRD ROW SEATS
To dismantle:
– operate release lever C-fig. 33and
guide the seat back until the “table”
position is reached; turn the tipped
seat again until the “wallet” position is
reached fig. 36;
– take belt Eand pull it upwards then
remove the whole seat from its hous-
ings on the floor runners.
Reverse the above mentioned pro-
cedure to reassemble the seat.Make sure the anchor-
age holes are always
clean; if debris has got in-
to them it interferes with the
seats being locked securely into
place.THIRD ROW BENCH SEAT
Moving the seat backwards
or forwards fig. 37
Lift lever Aand push the seat back-
wards or forwards.
It is possible to widen the luggage
compartment capacity from the out-
side by pulling handle Band pushing
the bench forwards.
fig. 36
F0B0411b
Before starting off again,
make sure that the seats
are facing the front of the
vehicle and are properly fastened
to their anchorage points. The
seat belts can only be used effec-
tively in this position.
fig. 37
F0B0286b

GETTING TO KNOW YOUR CAR
33
fig. 48
F0B0227b
fig. 49
F0B0024b
fig. 50
F0B0017b
Rear seats fig. 48-49
They can be adjusted for height. To
adjust it, lift or lower the head re-
straint to get the required position.
Lift the head restraint up to its max-
imum height, operate device A-fig. 49
and pull the rear head restraint up-
wards to remove it.ARMREST fig. 50
To adjust the armrest apply the fol-
lowing procedure:
– lift the armrest up to position 1;– lower the armrest fully, position 2;
– lift the armrest to the required po-
sition 3.

GETTING TO KNOW YOUR CAR
44
All restraint systems must show ho-
mologation data and control markings
on a tag which is solidly fastened to the
system and cannot be removed.
Children weighing than 1.5 m are,
with reference to restrain systems,
considered adults and can wear nor-
mal seat belts.
We recommend using Lineaccessori
Fiat child restraint systems for each
weight group. These systems were
specifically designed and tested for Fi-
at vehicles.GROUP 0 and 0+
Babies up to 13 kg are to be seated
in a cot type seat supporting the child’s
head facing backwards. This ensures
there is no stress on the child’s neck
in sudden decelerations.
The cot is secured with the seat belts
as shown in fig. 66. Furthermore, the
child must be strapped to the cot.GROUP 1
Children from 9 to 18 kg are to be
seated facing forward in child seats
with front cushions,fig. 67. The ve-
hicle seat belt secures both seat and
child.
The figure is only an ex-
ample. Follow the in-
structions for fastening
the specific child restraint system
you are using.
The figure is only an ex-
ample. Follow the in-
structions for fastening
the specific child restraint system
you are using.
fig. 66
F0B0194b

GETTING TO KNOW YOUR CAR
101
CIGAR LIGHTER fig. 135
To use the cigar lighter, with the ig-
nition key at M, press button A; after
about 15 seconds the button auto-
matically pops back into its original po-
sition and the cigar lighter is ready for
use.ASHTRAY fig. 135-136The passengers in the rear seats can
use the ashtray by placing cup Din the
removable litter container Eas illus-
trated in fig. 135.
Extract compartment Band lift tab
C to use the ashtray. Remove cup D
to empty the ashtray. When the cup
is extracted the compartment can be
used as a glass holder. The cigar lighter gets
very hot. Be careful how
you handle it and make
sure children do not use it: dan-
ger of fire or burns. Always make
sure that the cigar lighter does in
fact pop out after it has been
pushed in.
fig. 135
F0B0082b
fig. 136
F0B0291b
Do not use the ashtray
for waste paper: lighted
cigarette ends could set it
on fire.

CAR MAINTENANCE
213
CLEANING SEATS
AND FABRICS
Remove dust with a soft brush and
vacuum cleaner.
Brush the seats with a damp sponge
with water and a neutral soap.
CLEANING LEATHER SEATS
Remove the dry dirt with a chamois
leather or very slightly moist cloth
without exerting too much pressure.
Remove liquid or grease stains with
a dry absorbent cloth without rubbing.
Then wipe with a chamois leather or
soft cloth moistened with water and
neutral soap.
IMPORTANTNever use alcohol
or alcohol-based products.STEERING WHEEL/GEAR
LEVER KNOB WITH
GENUINE LEATHER
COVERING
These components shall only be
cleaned with water and neutral soap.
Never use spirit or alcohol-based
products.
Before using special products for
cleaning interiors, read carefully label
instructions and indications to make
sure they are free from spirit and/or
alcohol-based substances.
If when cleaning the windscreen with
special glass products, some drops fall
on the leather covering of the steer-
ing wheel/gear lever knob remove
them immediately and then clean with
water and neutral soap.
IMPORTANTTake the utmost
care when engaging the steering lock
to prevent scratching the leather cov-
ering.PLASTIC PARTS INSIDE
THE CAR
Use special products designed not to
alter the appearance of the compo-
nents.
IMPORTANTDo not use alcohol
or petrol to clean the instrument
panel.
Do not keep aerosol
cans in the vehicle. There
is the risk they might ex-
plode. Aerosol cans must never
be exposed to a temperature
above 50°C; when the weather
starts to get hot the temperature
inside the vehicle might go well
beyond that figure.