door lock FIAT ULYSSE 2008 2.G Owners Manual

GETTING TO KNOW YOUR CAR
11fig. 2
F0B0401b
THE FIAT CODE
SYSTEM
To further protect your vehicle from
attempted theft, it has been fitted with
an electronic engine immobiliser sys-
tem (called Fiat CODE) which is au-
tomatically activated when the ignition
key is removed. Each ignition key, in
fact, contains an electronic device,
which modulates a radio-frequency
signal emitted by a special aerial, built
into the ignition switch, during ignition.
The modulated signal is a “password”
with which the control unit recognis-
es the key. Engine ignition is enabled
only if the key is recognised by the sys-
tem.THE KEYS fig. 2
The following keys are supplied with
the car:
– two keys Aif the car is fitted with
remote central door locking system
and electronic alarm.
– two keys Bif the car is fitted with
remote central door locking system,
electronic alarm and powered side
sliding doors.The keys shall be used to:
– ignition switch;
– lock/unlock the driver and passen-
ger door
– operate remote door locking/un-
locking
– operate the alarm system (where
fitted)
– deactivate the passenger side airbag
– lock/unlock the fuel filler cap
– lock/unlock the glove compart-
ment.

GETTING TO KNOW YOUR CAR
13
A CODE card fig. 5is provided with
the keys. This CODE card bears the
electronic code used by the Fiat
Dealershipswhenever the vehicle
cannot be started. The key fig. 4is fitted with 4 but-
tons:
A -to activate the central locking
system, the alarm and the localisation
function;
B -to activate the central unlocking
system and deactivate the alarm;
C -to lock/unlock the right-hand
side sliding door;
D -to lock/unlock the left-hand side
sliding door.
By pressing button Athe so-called
“localisation” function is turned on: all
the passenger compartment lights and
direction indicators are switched on
for a couple of seconds. Such function
is recognised by the system up to a
distance of around 30 meters from the
vehicle.
The key is also fitted with a metal in-
sert Fwhich can be pushed inside the
key grip by pressing button E.The remote control inside the key
works on radio-frequency.
IMPORTANTIn order to ensure
perfect efficiency of the electronic de-
vices contained inside the keys, they
should never be exposed to direct
sunlight. When pressing the but-
ton E, take care to pre-
vent the metal insert
from causing harm or damage
when it comes out. The button
E should only be pressed when
the key is away from the body, in
particular from the eyes and
from objects that can be spoilt
(e.g. clothes). Make sure the key
can never be touched by others,
especially children, who may in-
advertently press button E.The electronic compo-
nents inside the key may
get damaged if the key is
submitted to sharp knocks.
fig. 4
F0B0403b
Press button Eagain to let it come
out from the key grip.

GETTING TO KNOW YOUR CAR
14
REPLACING THE KEY
BATTERIES fig. 6-7
If the doors do not lock and the di-
rection indicators do not come on
when the button on the remote con-
trol is pressed, replace the batteries
with others of the same time:
– open the metal insert;
– open the plastic casing Aby forc-
ing recess B;
– remove the printed circuit Cwith
the battery;
– extract the battery Dand replace
it respecting the polarity;
– refit the printed circuit Cwith the
battery facing inwards;
– close the plastic casing A.Since the electronic alarm absorbs
electricity, if you will not be using the
vehicle for more than a month, you
are advised to switch the system off
with the remote control. This will pre-
vent the battery from going flat. All the keys and the
CODE card must be
handed over to the new
owner when selling the car.
fig. 5
F0B0404b
This code is masked by a special
paint, which should be removed when
the CODE card is used. The CODE
card should therefore be kept in a safe
place and not in the vehicle.Used batteries pollute
the environment. Dispose
of them in the special
containers as specified by current
legislation or take them to your
nearest Fiat Dealership, which
will deal with their disposal. Do
not expose them to naked flames
and high temperatures. Keep out
of children’s reach.
fig. 6
F0B0440b
fig. 7
F0B0441b

GETTING TO KNOW YOUR CAR
16
ELECTRONIC
ALARM
(where fitted)
The vehicle is equipped with an elec-
tronic alarm with perimeter (external)
protection and volumetric (internal)
protection. To switch on the alarm,
press the button A-fig. 8on the re-
mote control.
This will be accompanied by the di-
rection indicator flashing and then the
red led on the dashboard A-fig. 9
flashing.
Door locking by turning the key
does not activate the alarm. When the alarm is triggered
The siren comes on, the direction in-
dicators and the headlights flash for
about 30 seconds when:
– - the doors, bonnet, boot or sun-
roof (where provided) are opened;
– a variation in the volume inside the
vehicle is experienced (do not leave the
windows open or animals inside the ve-
hicle when the alarm is switched on);
– if an attempt is made to neutralise
the alarm system without the remote
control.Switching the alarm system off
To switch the alarm system off, press
button B-fig. 8on the remote con-
trol.
The direction indicators will flash
rapidly for about 2 seconds.
If the alarm system has triggered, led
A-fig. 9will flash rapidly.
fig. 8
F0B0405b
fig. 9
F0B0003b

GETTING TO KNOW YOUR CAR
19
DOORS10 km/h is reached, the doors and the
tailgate are automatically locked.
When the key is turned to M, the ac-
tivation of this function is signalled by
a sound (“beep”). Press and keep but-
ton A-fig.12 pressed for more than
3 seconds to deactivate the above
mentioned function.
SECOND ROW CONTROL
ELECTRIC DEACTIVATION
fig. 13
Next to the electric window lock-
ing/unlocking controls on the driver’s
side, there is button Awhich prevents
rear row controls from being used and
therefore windows, sunroof (where
fitted) and side sliding doors from be-
ing opened by the passengers in the
second row.FRONT DOORS
Opening/closing by hand from
the outside fig. 14
Opening:turn the key to position
1and pull the door handle in the di-
rection of the arrow.
Closing:close the door and turn the
key to position 2.
IMPORTANT Insert the key right
into the lock before turning it.
fig. 12
F0B0012b
fig. 13
F0B0013b
fig. 14
F0B0407b
Always use these locks
when transporting chil-
dren.
Before opening a door
make sure that the oper-
ation can be performed in
safety conditions.
A buzzer will sound to inform the
driver that the outside lights are on
when a door is opened and the igni-
tion key is removed. Switch off the
lights, close the door or start the en-
gine to stop the buzzer. The vehicle
is fitted with button A-fig. 12, placed
next to the front ceiling lamp, to
lock/unlock the doors from the inside.
The vehicle is delivered to the cus-
tomer with the ”autoclose” system on.
It means that when a speed above

GETTING TO KNOW YOUR CAR
21
Door lock/unlock with the
remote control from outside
(where fitted) fig. 18
Right door:operate the key button
A with the remote control.
Left door:operate the key button
Bwith the remote control.Electric lock/unlock from inside
(where fitted) fig. 19-20
From the first row:
– press button A to open the left
sliding door, so the latch will unlock
and the door will open;
– press again button A to close the
left sliding door, but the latch will not
lock. To do it, press button C;
– press button Bto open the right
sliding door, so the latch will unlock
and the door will open;
– press again button Bto close the
right sliding door, but the latch will not
lock. To do it, press button C.From the second row:
– to lock/unlock press button Dcon-
nected to each sliding door.
Both doors are fitted with a safety
anticrushing device working as follows:
– during opening: when an obsta-
cle is detected the door stops auto-
matically;
– during closing: when an obsta-
cle is detected the door stops and au-
tomatically reverse its operation, thus
going back to a fully open position. In
this case, press one of the buttons on
the remote control, the front ceiling
lamp or the door panel to restore the
door operation.
Both stages are accompanied by
buzzer sound
fig. 18
F0B0408b
fig. 19
F0B0409b
fig. 20
F0B0221b

GETTING TO KNOW YOUR CAR
22
CENTRAL DOOR LOCKING
SYSTEM
From the outside
With the doors closed: insert and
turn the key in the lock of one of the
front doors.
From the inside
With the doors closed: press button
C-fig. 19placed next to the front ceil-
ing lamp.
Pressing or lifting one of the rear sill
buttons only locks or unlocks the par-
ticular door involved.
IMPORTANTIf one of the doors
is not shut properly or there is a fail-
ure in the system, the central locking
feature will not work and the direc-
tion indicators will not flash; after
some attempts, the device stops
working for around 20 seconds. In
these 20 seconds, the door can be
locked or unlocked manually without
the electrical system coming into play.
After the 20-second period, the con-
trol unit is ready to receive commands
once more.
If the reason for the malfunction has
been removed, the device will start to
work properly again. If not, it will cut
out once more.“Door open” alarm
If, with engine running, one of the
doors is not shut properly, the multi-
function display will show a dedicat-
ed message and the buzzer will sound.
SUPER DOOR LOCK
(where fitted)
To engage the super door lock using
the remote control, press button A-
fig. 8once and then press it again
within 5 seconds. After the first click
they will click again to signal that they
have been engaged.
To activate the super door lock with
the key, place it in the lock and hold
it in the locking position for a few sec-
onds until you hear the second click
indicating that the doors have been
locked.
This operation is necessary if you do
not wish to engage the electronic
alarm.When the super door
lock has been activated it
is impossible to open the
doors even from the inside; for
this reason do not use the super
door lock when there are pas-
sengers in the vehicle.
The super door lock is deactivated
when the doors are unlocked with a
key or remote control by pressing the
pushbutton B-fig. 8.

GETTING TO KNOW YOUR CAR
23
CHILD SAFETY LOCK
There can be 2 types of “Children
safety”: electric safety or mechanical
safety.
ELECTRICAL LOCK fig. 21
Next to the electric window lock-
ing/unlocking controls on the driver’s
side, there is button Awhich prevents
rear row controls from being used and
therefore windows, sunroof (where
fitted) and side sliding doors from be-
ing opened by the passengers in the
second row.
Any adjustments should
be made when the vehicle
is stationary.Always use these locks
when transporting chil-
dren.
2
1
fig. 22
F0B0014b
fig. 21
F0B0014b
MECHANICAL LOCK fig. 22
They are designed to prevent the
rear sliding doors being opened from
the inside:
position 1- lock off (the door can
be opened from the inside);
position 2- lock set (door locked).
The lock remains in the set position
even when the doors are unlocked
electrically.After activating the safe-
ty lock on both sliding
doors, operate the inside
lever to check the lock is really on. Always use these locks
when transporting chil-
dren.
IMPORTANTThese device works
only for the relative door.

GETTING TO KNOW YOUR CAR
36
Adjustment by hand fig. 55
If the mirror makes it difficult to get
through narrow gaps, fold it from po-
sition 1to position 2.
Electric folding (where fitted)
fig. 55
Folding is possible only when the ig-
nition key is at M.
To tilt the mirrors use button Bnext
to arrow O.
Locking the doors, door mirrors will
set automatically to locking position;
unlocking the doors, door mirrors will
set automatically to opening position.
If door mirrors were folded by press-
ing button Bbefore locking the doors,
next time doors are unlocked the mir-
rors will not set automatically to open-
ing position but you will have to press
button Bagain.SEAT BELTS
HOW TO USE THE SEAT
BELTS (FRONT AND REAR)
The belt should be worn keeping the
chest straight and rested against the
seat back.
To fasten the seat belt, take hold the
tongue A-fig. 56and insert it into the
buckle B, until you hear it click.
Pull the seat belt gently. If it jams, let
it rewind a little and pull it out again
without jerking.
To unfasten the belts, press button
C. Guide the belt with your hand as
it rewinds to prevent twisting.
Never press button C
when travelling.The seat belt reel mechanism will
adapt the belt to the body of the per-
son wearing it offering freedom of
movement.
When the car is parked on a steep
slope the reel mechanism may block;
this is normal.
The reel mechanism prevents the
webbing coming out when it is jerked
or if the car brakes sharply, as in col-
lision or when cornering at high speed.
fig. 56
F0B0229b
During adjustment,
avoid touching the mirror
and its support to prevent
finger pinching.

GETTING TO KNOW YOUR CAR
96
INTERIOR
EQUIPMENT
GLOVE COMPARTMENT
fig. 117
Pull handle Ato open the glove com-
partment.
Turning the key locks or unlocks the
compartment (where fitted).
Do not travel with the
glove compartment open
as this could cause injury
in the event of an accident.
fig. 117
F0B0088b
STOPPING THE ENGINE
Proceed as follows:
– release the accelerator pedal;
– press the brake pedal.
IMPORTANTOn a downhill and
the engine started, keep the vehicle
stopped only with the brake pedal; do
not press the accelerator pedal.
When stationary, the engine started
and the gear lever at D, Ror M(se-
quence mode), keep the brake pedal
depressed to prevent the car moving
with the engine idling.
If the car is stationary for a long time,
shift the gear lever to P.PARKING
Apply the handbrake and shift the
gear lever to P. Steer the wheels and
place a wedge or a stone under them
if the car is parked on a slope.
Do not leave the ignition key at Mto
prevent draining the battery charge.
Always take the ignition key with you
when leaving the car.
SOUND WARNINGS
(BUZZERS)
If you open the doors when the ig-
nition key has been removed or is at
S, a sound warning is emitted if the
gear lever is not in Pposition. Do not leave children
unsupervised in the vehi-
cle.