bulb FIAT ULYSSE 2009 2.G Owners Manual
[x] Cancel search | Manufacturer: FIAT, Model Year: 2009, Model line: ULYSSE, Model: FIAT ULYSSE 2009 2.GPages: 254, PDF Size: 3.56 MB
Page 160 of 254
IN AN EMERGENCY
159
When you have finished:
1)Arrange the replaced wheel in the
support under the floor.
2)Tighten the bolt with the jack han-
dle until the wheel support is well po-
sitioned and then put the cover back
to its place.
3)Close the tailgate.
4)Refit the jack and the jack handle
in the compartment.
5)Close the compartment with the
covering panel.IF A BULB BURNS
OUT
Modifications or repairs
to the electrical system
carried out incorrectly
and without bearing the features
of the system in mind can cause
malfunctions with the risk of fire.
You should, where pos-
sible, have your bulbs
changed at a Fiat Dealer-
ship. Correct operation of exter-
nal light beams are essential for
safe driving and compliance with
legal requirements.
fig. 11
F0B0126b
Only touch the metal
part when handling halo-
gen bulbs. If the transpar-
ent bulb is touched it reduces the
intensity of the light emitted and
can also reduce the life of the
bulb. If you touch the bulb acci-
dentally, rub it with a cloth moist-
ened with alcohol and leave it to
dry.
Halogen bulbs contain
pressurised gas which, if
broken, may cause small
fragments of glass to be project-
ed outwards.
153-183 ULYSSE ING:153-183 ULYSSE ING 13-11-2009 10:07 Pagina 159
Page 161 of 254
IN AN EMERGENCY
160
GENERAL INSTRUCTIONS
– When a light is not working, check
that it has not fused before changing
the bulb.
– For the location of the fuses, refer
to “If a fuse blows” in this chapter.
– Before replacing a bulb that does
not work, check that the contacts are
not oxidised.
– Burnt-out bulbs must be replaced
with ones of the same type and pow-
er.
– Always check the height of the
headlight beam after changing a bulb.TYPES OF BULBS fig. 12
Several types of bulbs are installed in
the vehicle:
A -Glass bulbs: clipped into position.
Pull to remove.
B -Bayonet bulbs: remove from the
bulb holder by pressing the bulb and
turning it anticlockwise.
C-D -Halogen bulbs: to remove the
bulb, release the clip holding the bulb
in place.
E -Xenon bulbs.
fig. 12
F0B0127b
153-183 ULYSSE ING:153-183 ULYSSE ING 13-11-2009 10:07 Pagina 160
Page 162 of 254
IN AN EMERGENCY
161
BULBS
Front side lights
Dipped beam headlights:
– halogen bulbs
– Xenon lights
Main beam headlights
Front fog lights
Direction indicators:
– front
– side
– rear
Taillights and brake lights
Third brake lights
Reversing light
Rear fog lights
Number plate light
Passenger compartment lights
Ceiling lights
Glove compartment lights
Courtesy lights
Puddle lightFIGURE 12
A
C
E
C
D
B
A
B
B
A
B
B
A
A
A
A
A
ATYPE
W5W
H7
D15
H7
H3
PY21W
WY5W
PY21W
P21/5W
W5WF14
P21W
P21W
W5W
W5W
W5W
W5W
W5W
W5WPOWER
5W
55W
35W
55W
55W
21W
5W
21W
21W/5W
5W
21W
21W
5W
5W
5W
5W
5W
5W
153-183 ULYSSE ING:153-183 ULYSSE ING 13-11-2009 10:07 Pagina 161
Page 163 of 254
IN AN EMERGENCY
162
IF AN EXTERIOR
LIGHT BURNS OUT
Modifications or repairs
to the electrical system
carried out incorrectly
and without bearing the features
of the system in mind can cause
malfunctions with the risk of fire.
IMPORTANTSee “If a bulb burns
out” for information on bulb types and
power when changing a bulb.FRONT LIGHT CLUSTER
Front headlights include front side
lights, main beam headlights, dipped
beam headlights, direction indicators
and front fog lights fig. 13:
A- main beam headlights;
B- front side lights;
C- dipped beam headlights;
D- direction indicators;
E- front fog lights.To replace a dipped beam headlight
remove the rubber cover 1-fig. 14by
turning it anticlockwise.
To replace front side lights and main
beam headlights remove the cover 2
by turning it anticlockwise.
To replace front fog lights remove the
cover 3by turning it anticlockwise.
To replace direction indicator bulbs
remove the bulb holder 4by turning
it anticlockwise.
fig. 13
F0B0130b
fig. 14
F0B0131b
153-183 ULYSSE ING:153-183 ULYSSE ING 13-11-2009 10:07 Pagina 162
Page 164 of 254
IN AN EMERGENCY
163
FRONT SIDE LIGHTS fig. 15
To replace a bulb:
– Remove the cover as 2previously
described.
– Remove the bulb holder Aby turn-
ing it slightly.
– Take off the clipped bulb Band re-
place it.
– Put the bulb holder back to its
place.MAIN BEAM HEADLIGHTS
fig. 16
To replace a bulb:
– Remove the cover as 2previously
described.
– Disconnect the electrical connec-
tion A.
– Release clip B.
– Take off bulb Cand replace it.
– Fit the new bulb by matching the
metal tab with the groove on the lamp.
– Refit clip B.
– Reconnect connector A.DIPPED BEAM HEADLIGHTS
With halogen bulbs fig. 17
To replace a bulb proceed as follows:
– Remove the rubber cap 1as de-
scribed previously.
– Turn the bulb holder Aclockwise
or counter-clockwise to release it
from the catches.
– Remove the snap fitted bulb Band
replace it
fig. 15
F0B0135b
fig. 16
F0B0134b
fig. 17
F0B0446b
153-183 ULYSSE ING:153-183 ULYSSE ING 13-11-2009 10:07 Pagina 163
Page 165 of 254
IN AN EMERGENCY
164
– Fit the new bulb into the bulb hold-
er (with protrusion facing upwards),
push the bulb forwards along the ve-
hicle axis until hearing the locking click
that indicates proper bulb securing.
– Refit the bulb holder into its seat
turning it clockwise or counter-clock-
wise to lock it to catches.
Xenon bulbs fig. 18
We recommend you to
have the bulb changed at
a Fiat Dealership.IMPORTANT The bulb replace-
ment procedure is described only as
information.
To replace a bulb:
– Remove the rubber cap 1as pre-
viously described.
– Release clip A.
– Disconnect connector B.
– Take off bulb Cand replace it.
– Fit the new bulb and connect con-
nector B.
– Refit clip A.Only touch the metal
part when handling
Xenon bulbs. If you touch
the transparent bulb accidental-
ly, rub it with a cloth moistened
with alcohol and leave it to dry.
fig. 18
F0B0129b
153-183 ULYSSE ING:153-183 ULYSSE ING 13-11-2009 10:07 Pagina 164
Page 166 of 254
IN AN EMERGENCY
165
FRONT DIRECTION
INDICATORS fig. 19
To replace a bulb:
– Turn the bulb holder Aanticlock-
wise and remove it.
– Remove bulb Bby pushing it slight-
ly and turning it anticlockwise (bayo-
net coupling).
– Replace the bulb.
– Refit the bulb holder by turning it
clockwise and check it is well fastened.FRONT FOG LIGHTS fig. 20
To replace a bulb:
– Remove cap 3as previously de-
scribed.
– Disconnect connector A.
– Release clip B.
– Take off bulb Cand replace it.
– Fit the new bulb by matching the
metal tab with the groove on the lamp.
– Refit clip B.
– Reconnect connector A.SIDE DIRECTION
INDICATORS fig. 21-22
To replace a bulb:
– Press the lens Ain direction 1so
to compress the inside clip B, then
remove the unit by pulling it in direc-
tion 2.
– Turn bulb holder C anticlockwise.
– Take off clipped bulb Dand replace
it.
– Refit bulb holder Cand the trans-
parent unit.
fig. 19
F0B0136b
fig. 20
F0B0132b
fig. 21
F0B0128b
153-183 ULYSSE ING:153-183 ULYSSE ING 13-11-2009 10:07 Pagina 165
Page 167 of 254
IN AN EMERGENCY
166
Be careful when remov-
ing the side direction in-
dicator unit not to dam-
age the bodywork or the trans-
parent glass.
REAR LIGHT CLUSTER
The rear light cluster includes brake
lights and taillights, direction indica-
tors, reversing light and rear fog lights
fig. 23:
A- direction indicators;
B- brake lights/taillights;C- reversing light;
D- rear fog lights.
To replace a bulb fig. 24-25:
– Remove cover Aby lifting it in the
points and direction shown by the ar-
rows.– Disconnect connector Band re-
lease the two fasteners C.
– Release wing nut Dand remove
the rear cluster.
fig. 22
F0B0137b
fig. 24
F0B0041b
fig. 23
F0B0115b
153-183 ULYSSE ING:153-183 ULYSSE ING 13-11-2009 10:07 Pagina 166
Page 168 of 254
IN AN EMERGENCY
167
– Take off the bulb holders by turn-
ing them slightly anticlockwise fig. 26:
A- Direction indicator bulb;
B- Brake light/taillight bulb;
C- Reversing light bulb;
D- Rear fog light bulb.– Remove the bulbs by pushing them
slightly and turning them anticlockwise
as shown in the figure.
– After replacement, refit the bulb
holder by turning it clockwise and
check it is well fastened.
– Refit the unit and drive in wing nut
D(outside) and the two inside fas-
tening devices C.
– Reconnect the electrical connec-
tor Band refit finish A.NUMBER PLATE LIGHTS
fig. 27
The number plate lights are next to
the tailgate handle (one for each side).
To replace a bulb:
– Remove the clipped transparent
unit Aas shown in the figure.
– Take off clipped bulb Band replace
it.
– Refit the transparent unit.
fig. 26
F0B0138b
fig. 27
F0B0144bfig. 25
F0B0263b
153-183 ULYSSE ING:153-183 ULYSSE ING 13-11-2009 10:07 Pagina 167
Page 169 of 254
IN AN EMERGENCY
168
THIRD BRAKE LIGHTS
fig. 28-29
To replace a bulb:
– Open the tailgate.
– Remove clipped cap A.
– Press tabs Band take off the bulb
holder Cfrom the unit.
– Identify the burnt bulb and replace
it.– Refit bulb holder C.
– Refit cap Aand check it is well fas-
tened.IF AN INTERIOR
LIGHT BURNS OUT
FRONT-REAR-CENTRAL
CEILING LIGHT fig. 30-31
To replace a bulb:
– Remove the clipped transparent
unit Aby levering as shown in the fig-
ure.
– Identify the burnt bulb and replace
it.
fig. 28
F0B0142bfig. 29
F0B0143b
fig. 31
F0B0147b
fig. 30
F0B0146b
153-183 ULYSSE ING:153-183 ULYSSE ING 13-11-2009 10:07 Pagina 168