low beam FIAT ULYSSE 2009 2.G Owners Manual
[x] Cancel search | Manufacturer: FIAT, Model Year: 2009, Model line: ULYSSE, Model: FIAT ULYSSE 2009 2.GPages: 254, PDF Size: 3.56 MB
Page 11 of 254
GETTING TO KNOW YOUR CAR
10
1.Side vents
2.Left-hand stalk: headlight control
3.Horn
4.Instrument panel: odometer display and warning lights
5.Right-hand stalk, windscreen washer, rear window
washer and trip computer
6.Gear lever
7.Central vents
8.Revolution counter
9.Speedometer
10.Fuel gauge with low fuel warning light and engine
coolant temperature gauge with warning light showing
when the temperature is too high
11.Sound system/Infotelematic Connect system display
(for versions/markets, where provided)
12.Sound system/Infotelematic Connect system (for ver-
sions/markets, where provided)
13.Passenger air bag14.Glove compartment
15.Climate system automatic controls
16.Hazard lights
17.Cigar lighter
18.Glove compartment/Infotelematic Connect system re-
mote controls (for versions/markets, where provided)
19.Console
20.Ashtray and glove compartment
21.Ignition switch
22.Sound system controls on steering wheel
23.Document compartment
24.Driver air bag
25.Cruise control control lever
26.Headlight beam adjuster (Xeno light versions excluded)
27.ASR system on/off.
001-077 ULYSSE ING:001-077 ULYSSE ING 5-11-2009 12:11 Pagina 10
Page 61 of 254
GETTING TO KNOW YOUR CAR
60
GLOW PLUGS
(Amber)
The light comes on when
the ignition key is turned to Mand
then goes off when the glow plugs
have reached the set temperature.
Start the engine immediately after
the warning light goes off.
IMPORTANTWhen the environ-
ment temperature is very high, the
warning light might come on for less
than a second.FUEL RESERVE
(Amber)
The warning light comes on
when 8 litres of fuel have remained in
the tank.
Refuel as soon as possible after the
warning light comes on. SERVICE WARNING
LIGHT (Red)
This warning light will turn
on in the following cases: low coolant
level, particulate filter failure, low par-
ticulate filter additive level, risk of
clogged particulate filter.
DIPPED HEADLIGHTS
(Green)
When the dipped-beam
headlamps are turned on.
RIGHT DIRECTION
INDICATOR (Green)
The warning light starts
flashing when the direction indicator
control stalk is lifted or together with
the left direction indicator, when the
hazard light button is pressed.
K
2
E
m
The warning light will come on when
the front passenger air bag is deacti-
vated.
REAR FOG LIGHTS
(Amber)
When the rear fog lights
are turned on.
ESP SYSTEM (Amber)
The light comes on when
you turn the ignition key to
M, but it should go out after a couple
of seconds.
If the warning light either stays on or
comes on while travelling contact a Fi-
at Dealership.
Warning light flashing when driving
indicates that the ESP system is active.
4
ñ
è
001-077 ULYSSE ING:001-077 ULYSSE ING 5-11-2009 12:11 Pagina 60
Page 62 of 254
GETTING TO KNOW YOUR CAR
61
LEFT DIRECTION
INDICATOR (Green)
The warning light starts
flashing when the direction indicator
control stalk is lifted or together with
the right direction indicator, when the
hazard light button is pressed.
FRONT FOG LIGHTS
(Green)
When the front fog lights
are turned on.
FULL BEAM
HEADLAMPS (Blue)
When the full-beam head-
lamps are turned on or when the “Fol-
low me home” device is on (see the
relative chapter).
R
5
1
FLAT TYRES
The warning light on the di-
al turns on (together with
message on the display and the
buzzer), when there is a pressure drop
in one or more tyres.
In this way the T.P.M.S. system warns
the driver that one or more tyre/s
is/are flat (i.e. punctured).
IMPORTANTStop travelling with
one or more flat tyre/s since road
holding could be jeopardised. Stop the
car without braking or steering
sharply. Change immediately punc-
tured wheel with space-saver spare
wheel (for versions/markets, where
provided - see section “In an emer-
gency”) and contact Fiat Dealership
as soon as possible.TYRE PRESSURE
MONITORING
SYSTEM FAILURE
The warning light on the dial turns
on (together with the message on the
display) when a failure is detected in
the T.P.M.S. system (for ver-
sions/markets, where provided).
Contact Fiat Dealershipas soon as
possible.
Should one or more wheels without
sensor be fitted, the instrument pan-
el warning light will come on (togeth-
er with the message on the display)
and stay on until fitting again the four
wheels with sensors.
ìè
001-077 ULYSSE ING:001-077 ULYSSE ING 5-11-2009 12:11 Pagina 61
Page 80 of 254
GETTING TO KNOW YOUR CAR
79
STEERING COLUMN
STALKS
LEFT-HAND STALK
The left-hand stalk controls most of
the outside lights. If you leave the lights
on when you take the key out of the
ignition an alarm will sound.
Outside lighting is possible with the
ignition key at M.
Side lights fig. 91
These lights turn on when you turn
the knurled knob Afrom åto
6.Dipped-beam headlights fig. 92
To switch on: turn the knurled knob
Afrom
6to 2/1.
Instrument panel indicator light 2
comes on.Follow me home fig. 93
(for versions/markets, where provided)
This function works for a set time
(45 seconds) and illuminates the area
in front of the vehicle. It is activated by
turning the ignition key to Sor, if the
ignition key has been removed, by
pushing the stalk towards the dash-
board. This function can be activated
by operating the stalk within 2 minutes
after the engine has been turned off.
If the vehicle is fitted with the side-
light and dipped-beam headlight auto-
matic switching on device, the “follow
me home” function is automatically ac-
tivated when the doors are opened.
fig. 91
F0B0416b
fig. 92
F0B0417b
fig. 93
F0B0418b
078-135 ULYSSE ING 10-03-2009 11:39 Pagina 79
Page 111 of 254
GETTING TO KNOW YOUR CAR
110
Do not travel with the
hatchback open: the ex-
haust fumes could enter
the vehicle.TAILGATE EMERGENCY
OPENING fig. 154
To unlock the tailgate in the event of
an electric failure, proceed as follows:
– introduce a screw driver into hole
A from inside the car
– to unlock the latch mechanically,
turn it on the left.
TRANSPORTING LUGGAGE
IMPORTANTFor vehicle versions
without Xenon lights travelling at night
with the luggage compartment loaded
it is necessary to adjust the dipped
beam headlight position (see “Head-
lamps” paragraph in this chapter).When loading the lug-
gage compartment, do
not exceed the permitted
weight limits (see “Technical
specifications” chapter). Also en-
sure that any objects in the lug-
gage compartment are firmly se-
cured and that they cannot be
thrown forward causing injury to
passengers if the vehicle brakes
suddenly.
Heavy loads which are
not securely anchored
could seriously injure pas-
sengers in the event of an acci-
dent. The addition of objects
(spoilers, etc.) on the rear
shelf or boot lid, except
those envisaged by the manufac-
turer, may prevent the tailgate
from working properly.
fig. 155
F0B0105b
fig. 154
F0B0169b
Anchoring the load fig. 155
The load can be secured with the
belts fastened to the appropriate rings
Ainside the luggage compartment.
These rings can also be used to fix
the luggage retaining net, where fitted.
078-135 ULYSSE ING 10-03-2009 11:39 Pagina 110
Page 115 of 254
GETTING TO KNOW YOUR CAR
114
HEADLAMPS
XENON LAMPS
(for versions/markets, where provided)
Xenon lamps work with a voltaic arc
in a pressure Xenon saturated envi-
ronment, in place of the traditional fil-
ament.
The produced light is far greater than
that of traditional lamps, both for its
quality (lighter) and its lighting range.
The advantages in using such lamps
are the following: less eyes fatigue, im-
proved driver’s orientation and driving
safety, especially with the bad weath-
er, with fog and/or inadequate road
signs, illumination of side bands usu-
ally in the shadow.Illumination of side bands consider-
ably improves driving safety because
the driver is able to identify other road
users on the road margins (pedestri-
ans, bikers and motor-bikers).
When the lights come on, the volta-
ic arc tension is very high, but then it
falls.
The maximum light is obtained after
0.5 seconds after turning the head-
lamps on.
The great light produced by this type
of headlamps requires an automatic
system for maintaining the headlight
beam constant and preventing dazzling
other vehicles in the event of sudden
braking, acceleration or while carrying
heavy loads. Never load the rack with
more than the weight al-
lowed (see the “Technical
specifications” section).
Be careful not to knock
the tailgate into objects
on the roof rack.
After travelling a few
miles, check that the an-
chorage bolts of the at-
tachments are still fully tight.
078-135 ULYSSE ING 10-03-2009 11:39 Pagina 114
Page 143 of 254
DRIVING YOUR CAR
142
– only use full-beam headlights when
you are driving outside the city and
when you are sure they do not annoy
other drivers;
– if the headlights are on full, dip
them when you meet cars going in the
other direction and pass them with the
headlights dipped;
– keep all lights clean;
– be careful of animals crossing the
road when driving in the country.
DRIVING IN THE RAIN
Rain and wet road surfaces spell dan-
ger.
All manoeuvres are more difficult on
a wet road because the friction of the
wheels on the tarmac is greatly re-
duced. This is why braking distances
are much longer and roadholding on
bends is lower.
The main suggestions are the fol-
lowing:
– reduce speed and keep a greater
safety distance from the cars in front;– if it is raining particularly heavily,
visibility is also reduced. In these cas-
es, switch on the dipped headlights
even if it is still daylight, to make your-
self easier to be seen;
– do not drive through puddles at
speed and hold on tightly to the wheel:
the loss of grip caused by taking a pud-
dle at speed can make you lose con-
trol of the vehicle (“aquaplaning”);
– move the ventilation controls to
the position for demisting the win-
dows (see the section “Getting to
know your car”), to avoid visibility
problems;
– periodically check the condition of
the windscreen wiper blades. DRIVING AT NIGHT
The main suggestions are the fol-
lowing:
– drive especially carefully: it is hard-
er to drive at night;
– slow down especially if the road is
not lit;
– at the first signs of sleepiness, stop:
continuing would be a risk to yourself
and everybody else. Only start driving
again when you have had enough rest;
– keep a greater safety distance from
the cars in front of you than during
daylight hours: it is hard to judge how
fast other cars are going when all you
can see are their lights;
– make sure the headlight beams are
properly positioned: if they are too
low, they reduce visibility and are hard
on the eyes. If they are too high they
can dazzle other drivers;
136-152 ULYSSE ING 10-03-2009 11:40 Pagina 142
Page 144 of 254
DRIVING YOUR CAR
143
Remember that fog also means the
tarmac is wet and therefore manoeu-
vres of all kinds are more difficult and
stopping distances are longer:
– keep a good distance from the cars
in front of you;
– when possible, avoid spurts of
speed or sudden deceleration;
– do not overtake other vehicles if
you can help it;
– if you are forced to stop your ve-
hicle (breakdown, limited visibility,
etc.), first try to stop off the road.
Then turn on the hazard lights and, if
possible, the dipped headlights;
– rhythmically sound the horn if you
realise another vehicle is approaching.DRIVING IN
THE MOUNTAINS
The main suggestions are the fol-
lowing:
– when driving downhill use the en-
gine brake by engaging a low gear so
as not to overheat the brakes;
– under no circumstances should you
drive downhill with the engine off or
with the vehicle in neutral, let alone
with the ignition key out;
– drive at moderate speed without
“cutting” corners;
– remember that overtaking while
going uphill is slower and therefore re-
quires more clear road. If you are be-
ing overtaken while driving uphill,
make it easier for the other vehicle
to pass. DRIVING IN FOG
If the fog is thick, do not start out on
a journey unless you absolutely have to.
If driving in mist, blanket fog or when
there is the danger of fog patches:
– keep your speed down;
– turn on the dipped headlights, rear
fog lights and front fog lights, if fitted,
even during the day. Do not drive with
your headlights at full-beam.
IMPORTANTOn stretches of
road with good visibility, switch off
your rear foglights; the brightness of
these lights could annoy the people
travelling in the cars behind.
136-152 ULYSSE ING 10-03-2009 11:40 Pagina 143
Page 161 of 254
IN AN EMERGENCY
160
GENERAL INSTRUCTIONS
– When a light is not working, check
that it has not fused before changing
the bulb.
– For the location of the fuses, refer
to “If a fuse blows” in this chapter.
– Before replacing a bulb that does
not work, check that the contacts are
not oxidised.
– Burnt-out bulbs must be replaced
with ones of the same type and pow-
er.
– Always check the height of the
headlight beam after changing a bulb.TYPES OF BULBS fig. 12
Several types of bulbs are installed in
the vehicle:
A -Glass bulbs: clipped into position.
Pull to remove.
B -Bayonet bulbs: remove from the
bulb holder by pressing the bulb and
turning it anticlockwise.
C-D -Halogen bulbs: to remove the
bulb, release the clip holding the bulb
in place.
E -Xenon bulbs.
fig. 12
F0B0127b
153-183 ULYSSE ING:153-183 ULYSSE ING 13-11-2009 10:07 Pagina 160
Page 164 of 254
IN AN EMERGENCY
163
FRONT SIDE LIGHTS fig. 15
To replace a bulb:
– Remove the cover as 2previously
described.
– Remove the bulb holder Aby turn-
ing it slightly.
– Take off the clipped bulb Band re-
place it.
– Put the bulb holder back to its
place.MAIN BEAM HEADLIGHTS
fig. 16
To replace a bulb:
– Remove the cover as 2previously
described.
– Disconnect the electrical connec-
tion A.
– Release clip B.
– Take off bulb Cand replace it.
– Fit the new bulb by matching the
metal tab with the groove on the lamp.
– Refit clip B.
– Reconnect connector A.DIPPED BEAM HEADLIGHTS
With halogen bulbs fig. 17
To replace a bulb proceed as follows:
– Remove the rubber cap 1as de-
scribed previously.
– Turn the bulb holder Aclockwise
or counter-clockwise to release it
from the catches.
– Remove the snap fitted bulb Band
replace it
fig. 15
F0B0135b
fig. 16
F0B0134b
fig. 17
F0B0446b
153-183 ULYSSE ING:153-183 ULYSSE ING 13-11-2009 10:07 Pagina 163