air condition FORD AEROSTAR 1996 1.G Owners Manual
[x] Cancel search | Manufacturer: FORD, Model Year: 1996, Model line: AEROSTAR, Model: FORD AEROSTAR 1996 1.GPages: 353, PDF Size: 2.87 MB
Page 33 of 353
31
*
[SR12070(ALL)07/95]
To ensure that the air bag system will operate as
intended in a crash, the system is equipped with
a diagnostic module, which controls a readiness
lamp and a warning tone. The diagnostic
module monitors its own circuits, the air bag
electrical system, the air bag readiness light, the
air bag power, and the air bag inflators.
%*
[SR12200(ALL)05/95]
The air bag system uses a readiness light on the
instrument cluster and a tone to indicate the
condition of the system. When you turn the
ignition key to the ON position, this light will
illuminate for approximately six (6) seconds and
then turn off. This indicates that the system is
operating normally. NOTE: Maintenance of the
air bag system is not required.
%*
[SR12300(ALL)06/95]
A problem with the system is indicated by one
or more of the following:
*
[SR12310(ALL)06/95]
q
the readiness light will either flash or stay lit,
*
[SR12320(ALL)06/95]
q
or it will not light immediately after ignition
is turned on,
*
[SR12330(ALL)06/95]
q
or a group of five beeps will be heard. The
tone pattern will repeat periodically until the
problem and light are repaired.
*
[SR12360(ALL)08/95]
If any of these things happen, have the air bag
system serviced at your Ford or Lincoln-Mercury
dealer immediately. Unless serviced, the air bag
Supplemental Restraint System may not function
properly in the event of a collision.
*
[SR12600(ALL)07/95]
RWARNING
Do not attempt to service, repair, or
modify the Air Bag Supplemental
Restraint System or its fuses. See your
Ford or Lincoln-Mercury dealer.
File:03cpsra.ex
Update:Tue Aug 29 17:35:04 1995
Page 73 of 353
72
*
[ST09900(ALL)01/95]
Have the exhaust and body ventilation systems
checked whenever:
*
[ST10000(ALL)02/95]
q
your vehicle is raised for service
*
[ST10100(ALL)02/95]
q
the sound of the exhaust system changes
*
[ST10200(ALL)01/95]
q
your vehicle has been damaged in a collision
*
[ST10300(ALL)01/95]
Improve your ventilation by keeping all air inlet
vents clear of snow, leaves, and other debris.
*
[ST10400(ALL)08/95]
If the engine is idling while you are stopped in
an open area for long periods of time, open the
windows at least one inch (2.5 cm). Also, adjust
the heating or air conditioning system to bring
in outside air.
*
[ST10600(ALL)03/91]
q
HEATING Ð Set fan speed at MEDIUM or
HIGH, the function selector knob on VENT,
FLOOR, MIX, or the DEFROST symbol and
the temperature control knob on any desired
position.
[ST10800(ALL)07/95]
q
AIR CONDITIONING Ð Set the fan speed
knob at MEDIUM or HIGH, the function
selector knob on NORM A/C or MAX A/C
and the temperature control knob on any
desired position.
File:04cpsta.ex
Update:Tue Aug 29 17:35:31 1995
Page 173 of 353
192 [DR16025(ALL)05/94]How the Electronic 4-Wheel Drive (E-4WD)
System Works
[DR16036(ALL)03/90]
Under normal driving conditions, when the road
is firm, dry and level, the engine power is
distributed one-third to the front axle and
two-thirds to the rear axle. However, if a wheel
begins to slip, the microprocessor will sense this
condition and signal the system to transmit more
power to the axle with more traction. (You may
feel a momentary surge of power.)
[DR16046(ALL)06/95]
NOTE: The microprocessor is disabled when
the brakes are applied or when the
transmission selector is in the P (Park)
or N (Neutral) positions.
[DR16055(ALL)05/94]
Driving Your Electronic 4-Wheel Drive
(E-4WD) Vehicle
[DR16065(ALL)03/95]
Since your E-4WD vehicle is unique, follow these
steps to be safe:
[DR16075(ALL)03/95]
q
Avoid unnecessary turns or other maneuvers
that could cause loss of control and possible
injury.
[DR16076(ALL)06/95]
q
Use the same size and type of tire and wheel
as originally provided for your vehicle and
inflate the tires to the manufacturer's
recommended air pressure.
[DR16077(ALL)03/95]
q
Become familiar with your vehicle's operating
characteristics and study this Owner Guide
for specific operating instructions. Be sure all
occupants wear the safety belts provided.
Drive cautiously, defensively, and at speeds
safe for current road conditions.
File:10cpdra.ex
Update:Tue Aug 29 17:45:28 1995
Page 190 of 353
209 %
*
[DR30701(ALL)03/91]
Gross Vehicle Weight Rating (GVWR)
*
[DR30750(ALL)10/94]
To avoid overloading a vehicle, the owner
should observe the manufacturer's specified
Gross Vehicle Weight Rating. The GVWR is the
maximum total weight of base vehicle,
passengers, optional components and cargo that
a particular vehicle was designed to carry.
%*
[DR30801(ALL)01/93]
Gross Axle Weight Rating (GAWR)
*
[DR30850(ALL)03/91]
We have all seen a car or a truck that is loaded
down in the rear and riding high in the front.
This is a dangerous condition that usually means
that the rear suspension components are under
severe strain and that vehicle handling is
impaired. There is more to carrying a load than
just payload or GVWR.
*
[DR30901(ALL)03/91]
Your Safety Compliance Certification Label not
only gives the GVWR, it also gives the Gross
Axle Weight Rating (GAWR) which is the
carrying capacity for each axle system. For
trucks, the rear axle will be designed to carry
more weight than the front.
*
[DR30950(ALL)06/92]
The rating is based on the carrying capacity of
thelowest ratedaxle and suspension component
as well as other factors. This is why it's so
important to observe vehicle loading ratings.
Overloading a vehicle punishes components and
can lead to shortened service life or outright
failure.
*
[DR31001(ALL)06/92]
The capacity of the tires is included as part of
the axle and suspension system, which is to be
considered when determining the lowest rated
component. Tires are rated to carry a specific
maximum load at a specific maximum tire
pressure.
File:10cpdra.ex
Update:Tue Aug 29 17:45:28 1995
Page 203 of 353
222
*
[DR39600(ALL)11/89]
When turning, drive slightly beyond the normal
turning point so the trailer wheels will clear
curbs or other obstructions.
*
[DR39725(ALL)03/95]
When stopped in traffic for long periods of time
in hot weather, place the gearshift selector lever
in P (PARK) to increase the engine idle speed.
This aids in engine cooling and air conditioner
efficiency. If the engine overheats, move the
function selector knob to VENT to stop the
compressor and increase the engine speed for a
short time.
*
[DR39800(ALL)05/90]
RWARNING
Do not tow a trailer when using a
temporary spare tire.
*
[DR39900(ALL)05/90]
Vehicles with trailers should not be parked on a
grade. However, if you must park on a grade,
place wheel chocks under the trailer's wheels as
follows:
*
[DR40000(ALL)05/95]
q
Apply the brake pedal and hold.
*
[DR40100(ALL)11/89]
q
Have another person place the wheel chocks
under the trailer wheels.
*
[DR40200(ALL)08/95]
q
With the chocks in place, release the brake
pedal, making sure the chocks are holding.
[DR40350(ALL)08/95]
q
Apply the parking brake by pressing the
brake pedal down firmly with your right foot
while applying the parking brake with your
right hand.
*
[DR40575(ALL)06/95]
q
Shift the gearshift lever into P (Park).
File:10cpdra.ex
Update:Tue Aug 29 17:45:28 1995
Page 244 of 353
266
*
[SV01300(ALL)03/95]
Ford Motor Company recommends that you
perform the Owner Maintenance Checks listed in
theMaintenance Schedule and Recordbooklet.
These services are important for the proper
operation of your vehicle. In addition to the
conditions listed in the Owner Maintenance
Checklist, be alert for any unusual noise,
vibration, or other indication that your vehicle
may need service. If you do notice something
unusual, see that your vehicle is serviced
promptly.
*
[SV01350(ALL)03/95]
Use only recommended fuels, lubricants, fluids,
and service parts conforming to Ford
specifications. Motorcraft parts are designed and
built to provide the best performance in your
vehicle. Using these parts for replacement is
your assurance that Ford-built quality stays in
your vehicle.
%*
[SV01400(ALL)04/95]
NOTE: Always dispose of used automotive
fluids in a responsible manner. Follow
your community's standards for
disposing of these types of fluids. Call
your local recycling center to find out
about recycling automotive fluids.
%
*
[SV01600(ALL)06/95]
Precautions When Servicing Your
Vehicle
*
[SV01700(ALL)06/95]
Be especially careful when inspecting or
servicing your vehicle. Here are some general
precautions for your safety:
*
[SV01900(ALL)06/95]
q
If you must work with the engine running,
avoid wearing loose clothing or jewelry that
could get caught in moving parts. Take
appropriate precautions with long hair.
*
[SV02000(ALL)06/95]
q
Do not work on a vehicle in an enclosed
space with the engine running, unless you are
sure you have enough ventilation.
File:15cpsva.ex
Update:Tue Aug 29 17:51:51 1995
Page 245 of 353
267
*
[SV02100(ALL)08/95]
q
Never get under a vehicle while it is
supported only by a jack. If you must work
under a vehicle, use safety stands.
*
[SV02200(ALL)06/95]
q
Keep all lit cigarettes and other smoking
materials away from the battery and all
fuel-related parts.
*
[SV02500(ALL)03/95]
If you disconnect the battery, the engine must
ªrelearnº its idle conditions before your vehicle
will drive properly. To find out how the engine
does this, seeBatteryin this chapter.
*
[SV02600(ALL)03/95]
Working with the engine off:
*
[SV02650(ALL)03/95]
1. Set the parking brake fully and make sure
that the gearshift is securely latched in P
(Park).
*
[SV02700(ALL)06/95]
2. Remove the key from the ignition after you
turn the engine off.
*
[SV02725(ALL)06/95]
3. Block the wheels. This will prevent your
vehicle from moving unexpectedly.
*
[SV02750(ALL)03/95]
Working with the engine on:
*
[SV02785(ALL)03/95]
1. Set the parking brake fully and make sure
that the gearshift is securely latched in P
(Park).
*
[SV02800(ALL)03/95]
2. Block the wheels. This will prevent your
vehicle from moving unexpectedly.
*
[SV02900(ALL)02/95]
RWARNING
Do not start your engine with the air
cleaner removed and do not remove it
while the engine is running.
File:15cpsva.ex
Update:Tue Aug 29 17:51:51 1995
Page 254 of 353
276 %
*
[SV07500(ALL)06/95]
Choosing the Right Fuel
*
[SV07600(ALL)06/95]
Use only UNLEADED FUEL in your vehicle.
Using leaded fuel is prohibited by federal law.
Your warranty may not apply if your vehicle is
damaged because you used the wrong fuel.
*
[SV07625(ALL)08/95]
Vehicle inspection programs may detect
misfueling. Under these circumstances, you may
be required by law to make costly repairs at
your own expense.
%*
[SV08750(ALL)08/95]
Octane recommendations
*
[SV08800(ALL)08/95]
Your engine is designed to use regular
unleaded fuel with an octane rating of 87.In
most cases, it is not necessary to use a fuel with
an octane rating higher than 87. At service
stations, the octane rating is displayed on a label
on the pumps.
*
[SV08900(ALL)06/95]
one inch art:0060001-C
Typical octane rating label
*
[SV09050(ALL)07/95]
In some parts of the country, ªregularº grade
fuels are sold with octane ratings of 86 or even
less, especially in high altitude areas. We
recommend that you do not use these fuels.
Always use a fuel with an octane rating of 87,
even if it is sold as a ªmidgradeº or ªpremium.º
[SV09200(ALL)08/95]
Do not be concerned if your vehicle sometimes
knocks lightly when you drive up a hill or when
you accelerate. However, if a fuel with the
recommended octane rating knocks heavily
under all driving conditions or knocks lightly
driving at cruising speed on level roads, see
your dealer or a qualified service technician.
Persistent, heavy knocking can damage the
engine.
File:15cpsva.ex
Update:Tue Aug 29 17:51:51 1995
Page 255 of 353
277 %
*
[SV09300(ALL)08/95]
Fuel quality
*
[SV09450(ALL)06/95]
If you are experiencing starting, rough idle or
hesitation problems when the engine is cold, it
may be caused by fuel with low volatility. Try a
different brand of fuel. If the condition persists,
see your dealer or a qualified service technician.
*
[SV09455(ALL)08/95]
Using a high-quality fuel makes your vehicle
more responsive and maintains its good fuel
economy and emissions by:
*
[SV09460(ALL)08/95]
q
minimizing deposits in fuel injectors,
combustion chambers and on intake valves.
*
[SV09465(ALL)08/95]
q
assuring quick starting and smooth warm-up.
*
[SV09470(ALL)08/95]
q
protecting the fuel system from vapor lock in
very hot weather, which causes the engine to
hesitate or stall and makes restarts difficult.
*
[SV09475(ALL)08/95]
q
protecting your fuel system from rusting.
*
[SV09480(ALL)08/95]
q
preventing the fuel lines from freezing.
*
[SV09485(ALL)08/95]
q
preventing the fuel system from ªgumming
upº when your vehicle is not used for long
periods of time.
*
[SV09500(ALL)06/95]
It should not be necessary to add any
aftermarket products to your fuel tank if you
continue to use a high-quality fuel.
%*
[SV09600(ALL)04/95]
Gasolines for clean air
*
[SV09900(ALL)06/95]
Fuels in certain areas of the country are required
to contain oxygenates to improve air quality.
Common oxygenates are ethanol or grain alcohol
(blended at no more than 10%), methanol or
wood alcohol (blended at no more than 5% with
cosolvents and additives), and MTBE or methyl
tertiary butyl ether (blended at no more than
15%).
File:15cpsva.ex
Update:Tue Aug 29 17:51:51 1995
Page 273 of 353
295
*
[SV25900(ALL)05/95]
RWARNING
Driving too fast for conditions creates the
possibility of loss of vehicle control.
Driving at very high speeds for extended
periods of time may result in damage to
vehicle components.
%*
[SV26100(ALL)05/95]
At least once a month, check the pressure in all
your vehicle's tires, including the spare. Use an
accurate tire pressure gauge. Check the tire
pressure when tires are cold, after the vehicle
has been parked for at least one hour or has
been driven less than 3 miles (5 km). You can
find proper cold pressure and load limits of
recommended size tires on the Safety
Compliance Certification Label.
*
[SV26150(ALL)05/95]
RWARNING
Improperly inflated tires can affect vehicle
handling and can fail suddenly, possibly
resulting in loss of vehicle control.
%*
[SV26200(ALL)08/95]
Tire Inspection and Maintenance
*
[SV26300(ALL)02/95]
Inspect the tire treads, and remove stones, nails,
glass or other objects that may be wedged in the
tread grooves. Check for holes or cuts that may
permit air to leak from the tire, and make the
necessary repairs.
*
[SV26400(ALL)10/89]
Inspect the tire side walls for cuts, bruises and
other damage. If you suspect internal damage to
the tire, have it demounted and checked. You
may need to repair or replace it.
File:15cpsva.ex
Update:Tue Aug 29 17:51:51 1995