remove seats FORD AEROSTAR 1996 1.G Owners Manual
[x] Cancel search | Manufacturer: FORD, Model Year: 1996, Model line: AEROSTAR, Model: FORD AEROSTAR 1996 1.GPages: 353, PDF Size: 2.87 MB
Page 49 of 353
47 [SR27812(ALL)08/95]
Until a floor anchor is installed, follow these
steps to install a tethered child safety seat in the
front seat:
[SR27814(ALL)08/95]
1. Buckle the lap/shoulder belt in the seat
directly behind the front passenger seat.
[SR27816(ALL)08/95]
2. Pull all the stored belt out of the rear seat
belt retractor to switch the retractor to
automatic locking mode.
*
[SR27818(ALL)07/95]
3. Let the retractor wind up the slack from the
lap/shoulder belt.
[SR27820(ALL)08/95]
4. Install the child safety seat in the right front
seat. Refer to the previous section on
Installing Child Safety Seats. Hook the tether
strap around the webbing near the center of
the shoulder portion of the lap/shoulder
belt.
*
[SR27822(ALL)07/95]
5. Tighten the tether strap.
[SR27824(ALL)08/95]
Until floor-mounted tether anchors are installed,
tether straps of child safety seats in the second
row may be anchored to lap/shoulder belts for
the third row, following the five steps above, or
to the tongue of the third row lap belt.
*
[SR27830(ALL)05/95]
RWARNING
Failure to follow these precautions could
increase the chance of injury in an
accident.
*
[SR27840(ALL)05/95]
RWARNING
If the anchor bolt(s) is ever removed, the
hole(s) in the floor must be sealed to
prevent the possibility of exhaust fumes
entering the passenger compartment.
File:03cpsra.ex
Update:Tue Aug 29 17:35:04 1995
Page 58 of 353
56
*
[SR30380(ALL)05/95]
To remove the child from the built-in child
seat:
[SR30390(ALL)06/95]
1. Squeeze the tabs on the top and bottom of
the chest clip and pull the halves apart to
open the chest clip. Refer to Figure 8.
*
[SR30400(ALL)06/95]
2. Press the release button on the crotch safety
belt buckle.
[SR30410(ALL)05/95]
3. Slide the shoulder belts off the child's
shoulders and remove the child. Refer to
Figure 6.
*
[SR30420(ALL)06/95]
To stow the built-in child seat:
[SR30430(ALL)05/95]
1. Return the child seat cushion to the upright
position and lift the protector flap toward
the headrest.
[SR30440(ALL)05/95]
2. Fasten the snaps securely.
[SR30450(ALL)05/95]
3. Pull on the headrest release strap and rotate
the headrest downward until it latches
against the child seat cushion.
[SR30460(ALL)05/95]
RWARNING
Always fasten the protector flap snaps
when stowing your child seats to prevent
the child seat cushion from rotating
forward in a collision.
[SR30470(ALL)05/95]
The seat can now be used by an adult.
File:03cpsra.ex
Update:Tue Aug 29 17:35:04 1995
Page 59 of 353
57
*
[SR30480(ALL)05/95]
Inspection after a collision
*
[SR30490(ALL)06/95]
RWARNING
All built-in child restraints, including
seats, buckles, retractors, seat latches,
interlocks, and attaching hardware should
be inspected by a qualified dealer
technician after any collision.
*
[SR30495(ALL)08/95]
If the child seat was in use during a collision,
Ford recommends replacing it. However, if the
collision was minor and a qualified technician
finds that the child restraints do not show
damage and continue to operate properly, they
do not need to be replaced. If there is any
bending of the vehicle seatback or seat structure,
it should also be replaced. Built-in child seats
not in use during a collision should also be
inspected and replaced if either damage or
improper operation is noted.
*
[SR30500(ALL)05/95]
Built-in child seat maintenance
*
[SR30510(ALL)05/95]
Regularly inspect the lap and shoulder belts
system of your child seat. See your Ford dealer
if the shoulder belt webbing is frayed, or if the
buckle and tongue are damaged and/or do not
function properly.
%*
[SR30520(ALL)05/95]
Cleaning
*
[SR30530(ALL)08/95]
Your Built-In Child Seat may be cleaned with
mild soap and water. Do not use household
cleaners as they may weaken the webbing or
damage the plastic parts. For your convenience,
the liner can be removed, machine-washed, and
air-dried.
File:03cpsra.ex
Update:Tue Aug 29 17:35:04 1995
Page 112 of 353
131 %
*
[FV31201(ALL)12/91]
Quick Release Rear Captain Chairs
*
[FV31400(ALL)12/91]
To remove:
[FV31500(ALL)02/92]
1. For right hand seats, lift and rotate the seat
latch handle (located under the seat)
rearward, causing the J hook to disengage
from the front floor well retainer.
[FV31600(ALL)02/92]
For left hand seats, lift and rotate the seat
latch handle (located under the seat)
rearward, causing the J hook to disengage
from the front floor well retainer. Disengage
the lap/shoulder safety belt from the seat by
inserting a key or similar device into the slot
in the detachable anchor and lifting upward.
Stow the tongue end of the detachable
anchor as shown.
[FV31801(ALL)05/89]
2. Push the seat assembly rearward to
disengage the front and rear floor hooks and
lift the seat assembly from the vehicle.
File:08cpfva.ex
Update:Tue Aug 29 17:41:55 1995
Page 113 of 353
132
*
[FV32200(ALL)12/91]
To install the rear bucket seat:
[FV32300(ALL)12/91]
1. Lift the seat assembly into the vehicle and
drop the front and rear floor hooks into the
floor wells at a point just behind the floor
attachment pins.
[FV32500(ALL)05/89]
2. Rotate the seat latch handle forward, causing
the J hook to engage over the front of the
foremost well retainer.
[FV32801(ALL)02/92]
3. For right hand seats, continue rotating the
seat latch handle until it comes to a
complete stop on the top of the tube. This
will cause the seat assembly to slide forward,
engaging the front and rear floor hooks with
the floor well retainers.
[FV32901(ALL)02/92]
For left hand seats, push the seat latch
handle downward to a full stop. This locks
the seat in position. Before you engage the
safety belt, be sure it is not twisted. Remove
any twist, then insert the tongue end of the
detachable anchor into the detachable anchor
until you hear a ªsnapº and feel the latch
engage.
*
[FV33300(ALL)05/95]
RWARNING
Check to see that the seat is latched
securely in position. Keep floor area free
of objects that would prevent proper seat
engagement. Never attempt to adjust the
seat latch while the vehicle is in motion.
File:08cpfva.ex
Update:Tue Aug 29 17:41:55 1995
Page 114 of 353
133 [FV33601(ALL)05/89]
Two and Three Passenger Bench Seats and
Seat Bed Assemblies
[FV33700(ALL)07/92]
NOTE: If your vehicle is equipped with a
Built-In Child Seat, make sure the
child seat is properly stowed before
operating the seat bed.
*
[FV33801(ALL)03/91]
To remove seat assembly:
*
[FV33901(ALL)06/92]
1. Disengage the lap/shoulder safety belt from
the seat by inserting a key or screwdriver
into the slot in the detachable anchor and
lifting upward. Stow the tongue end of the
detachable anchor as shown in the
illustration.
File:08cpfva.ex
Update:Tue Aug 29 17:41:55 1995
Page 120 of 353
139
*
[FV35400(ALL)10/90]
4. Ensure that the latch handles are fully seated
in the down position.
[FV35500(ALL)06/95]
5. Before you engage the safety belt, be sure it
is not twisted. A twisted safety belt may
cause the retractor to work improperly.
Remove any twist, then insert the tongue
end of the detachable anchor into the
detachable anchor until you hear a ªsnapº
and feel the latch engage. Refer to the
previous illustration.
[FV35600(ALL)12/91]
The two passenger bench or bed seat must be
installed in the first row behind the front seats
on wagons with seven passenger seating.
*
[FV35701(ALL)01/92]
To fold down the rear seatback:
[FV35801(ALL)07/92]
To lower the rear seatback down to its cargo or
bed position, release the seatback latch by
moving the release lever forward for the bench
seat or upward for the seat bed. Then fold the
seatback down. The latch will re-engage in the
cargo position.
[FV35901(ALL)08/95]
To raise the seatback, release the seatback latch
and rotate the seatback upwards until the latch
re-engages. (A slight downward pressure on the
bench seat seatback will reduce effort on the
latch.)
File:08cpfva.ex
Update:Tue Aug 29 17:41:55 1995
Page 123 of 353
142 %
*
[FV47000(ALL)03/94]
Using the Power Lumbar Support and Side
Bolsters
[FV47100(ALL)12/91]
Inflating the Lumbar Support (If equipped)
[FV47300(ALL)06/95]
If your vehicle is equipped with this option, you
can inflate a lumbar support pad in the seatback.
To inflate the lumbar pad, push the INFLATE
side of the rocker switch. To deflate, push the
DEFLATE side of the switch.
[FV48100(ALL)02/92]
quarter page art:0020244-B
Power lumbar switch
%*
[FV49000(ALL)04/95]
Cleaning the Seats
*
[FV49050(ALL)05/95]
Vinyl
*
[FV49100(ALL)05/95]
For routine cleaning, wipe the surface with a
soft, damp cloth. For more thorough cleaning,
wipe the surface with a leather and vinyl cleaner
or a mild soap.
%*
[FV49150(ALL)04/95]
Fabric
*
[FV49200(ALL)05/95]
Remove dust and loose dirt with a whisk broom
or a vacuum cleaner. Remove fresh spots
immediately. Follow the directions that come
with the cleaner.
*
[FV49250(ALL)04/95]
NOTE: Before using any cleaner, test it on a
small, hidden area of fabric. If the
fabric's color or texture is adversely
affected by a particular cleaner, do not
use it.
File:08cpfva.ex
Update:Tue Aug 29 17:41:55 1995