turn signal FORD AEROSTAR 1996 1.G Owners Manual
[x] Cancel search | Manufacturer: FORD, Model Year: 1996, Model line: AEROSTAR, Model: FORD AEROSTAR 1996 1.GPages: 353, PDF Size: 2.87 MB
Page 81 of 353
80
*
[LG05300(ALL)05/95]
one inch art:0020048-A
Check engine warning light symbol
[LG05525(ALL)03/94]
Electronic 4-Wheel Drive Warning Light
(If equipped)
[LG05550(ALL)03/95]
The Electronic 4-Wheel Drive Warning Light
turns on when the Electronic 4-Wheel Drive
system is not working properly. This light comes
on briefly when you turn the ignition key to the
ON position, but should turn off when the
engine starts. If the light does not come on when
you turn the ignition to the ON position, or if it
comes on and stays on when you are driving,
have your vehicle serviced as soon as possible.
[LG05560(ALL)03/94]
The 4WD light will go off after a few seconds
and stay off if all systems are operating
correctly. If a problem is detected, the 4WD
warning light will flash a certain number of
times indicating the location of the problem. The
flashing will continue until the problem is
corrected. Each time the ignition key is turned
on the controller will detect the problem and
flash the signal. The 4WD system remains safe to
operate and the vehicle should be returned for
service.
[LG05575(ALL)03/94]
one inch art:0020529-B
Electronic 4-wheel drive warning light
File:05cplga.ex
Update:Tue Aug 29 17:36:50 1995
Page 90 of 353
109
Steering Column Controls
*
[SC00400(ALL)01/95]
The controls on the steering column and wheel
are designed to give you easy access to the
controls while you are driving.
%
*
[SC00500(ALL)01/95]
The Turn Signal Lever
*
[SC00600(ALL)01/95]
You can use the turn signal lever on the left side
of the steering column to:
*
[SC00700(ALL)03/95]
q
operate the turn signals and cornering lamps
*
[SC00800(ALL)01/95]
q
turn the high beams on/off
*
[SC00900(ALL)05/95]
q
flash the lamps
*
[SC01000(ALL)01/95]
q
turn the windshield wipers and washer
on/off
%*
[SC01100(ALL)01/95]
Turn Signals
[SC01700(ALL)05/95]
one third page art:0095013-A
Turn signal operation
File:07cpsca.ex
Update:Tue Aug 29 17:38:34 1995
Page 91 of 353
110
*
[SC01800(ALL)11/89]
If the turn indicator light in the instrument
panel does not illuminate or remains on (doesn't
flash) when you signal a turn, the turn signaling
system is malfunctioning. Have this condition
corrected as soon as possible, but make sure that
you use the accepted hand signals in the
meantime.
%*
[SC03200(ALL)03/95]
High Beams and Flashing the Lamps
[SC03800(ALL)05/95]
one third page art:0095014-A
Headlamp high beam and flash-to-pass operation
%*
[SC04400(ALL)03/95]
Windshield Wipers and Washer
*
[SC04500(ALL)03/95]
To turn on the windshield wipers, the ignition
key must be turned to the ON or ACC position.
[SC04950(ALL)05/95]
one third page art:0095015-A
Interval wiper on turn signal lever Ð wiper and washer
operation
File:07cpsca.ex
Update:Tue Aug 29 17:38:34 1995
Page 92 of 353
111
*
[SC05000(ALL)02/95]
To set the interval wipers, rotate the knob at the
end of the turn signal lever toward or away
from the instrument panel to the interval
operation you desire.
*
[SC05200(ALL)08/95]
To clean the windshield, push in the end of the
wiper knob. For a constant spray, keep the knob
pushed in. After you release the knob, the
wipers operate for two to three cycles before
turning off (if wipers were off) or returning to
the selected setting.
[SC05250(ALL)06/95]
NOTE: The addition of shields to the front of
the vehicle (e.g., bug shields) may
adversely affect the windshield washer
system from delivering fluid to the
windshield. Devices such as bug
shields are not recommended for your
Ford vehicle.
*
[SC05300(ALL)01/95]
Do not try to clean the windshield when the
washer fluid container is empty or activate the
washers at any time for more than 15 seconds
continuously. This could damage the washer
pump system.
*
[SC05400(ALL)01/93]
RWARNING
In freezing weather, the washer solution
may freeze on the windshield and obscure
your vision. Always warm up the
windshield with the defroster before you
use the washer fluid. If you cannot see
through the windshield clearly, it can
increase the risk of being involved in a
collision.
*
[SC005450(ALL)07/95]
For information about refilling the washer fluid
or replacing your windshield wiper blades, see
Windshield washer fluid and Wipersin the Index.
File:07cpsca.ex
Update:Tue Aug 29 17:38:34 1995
Page 95 of 353
114
%*
[SC05600(ALL)01/95]
Horn
*
[SC05800(ALL)05/95]
To sound the horn, press either horn pad.
*
[SC06150(ALL)06/93]
one third page art:0020086-B
Horn location (with speed control option)
%*
[SC06200(ALL)05/95]
Tilt Steering (If equipped)
*
[SC06350(ALL)02/95]
RWARNING
Never adjust the steering wheel when the
vehicle is moving. You could lose control
of the vehicle and injure someone.
[SC06500(ALL)07/95]
one third page art:0020089-C
Turn signal and tilt steering release lever
File:07cpsca.ex
Update:Tue Aug 29 17:38:34 1995
Page 163 of 353
182 [AS07850(ALL)00/95]Using headphones with the rear seat
controls
[AS07855(ALL)08/95]
Two 3.5mm headphone jacks have been
provided on the rear seat controls. Plug
headphone(s) into the provided jack(s) to
operate.
%*
[AS07860(ALL)08/95]
Common Radio Reception Conditions
*
[AS07865(ALL)08/95]
Several conditions prevent FM reception from
being completely clear and noise-free, such as
the following:
*
[AS07870(ALL)08/95]
1. Distance/Strength
*
[AS07875(ALL)08/95]
The strength of the FM signal is directly related
to the distance the signal must travel. The
listenable range of an average FM signal is
approximately 25 miles (40 kilometers). Beyond
this distance, the radio is operating in a fringe
area and the signal becomes weaker.
*
[AS07880(ALL)08/95]
NOTE: Always make sure your antenna
(whether you have a power antenna or
a manually adjustable antenna) is fully
extended to its maximum length for
proper reception. If your antenna is not
fully extended, you may experience
signal loss while traveling in fringe
reception areas.
*
[AS07885(ALL)08/95]
2. Terrain
*
[AS07890(ALL)08/95]
The terrain (hilly, mountainous, tall buildings) of
the area over which the signal travels may
prevent the FM signal from being noise-free.
*
[AS07895(ALL)08/95]
If there is a building or large structure between
the antenna and station, some of the signal
ªbendsº around the building, but certain spots
receive almost no signal. Moving out of the
ªshadowº of the structure will allow the station
to return to normal.
File:09cpasa.ex
Update:Tue Aug 29 17:42:51 1995
Page 164 of 353
183
*
[AS07900(ALL)08/95]
When the radio waves are reflected off objects or
structures, the reflected signal cancels the normal
signal, causing the antenna to pick up noise and
distortion. Cancellation effects are most
prominent in metropolitan areas, but also can
become quite severe in hilly terrain and
depressed roadways.
*
[AS07905(ALL)08/95]
To minimize these conditions, a stereo/mono
blend circuit has been incorporated into this
system. This feature automatically switches a
weak stereo signal to a clearer monaural signal,
which improves the quality of reception.
*
[AS07910(ALL)08/95]
Several sources of static are normal conditions
on AM frequencies. These can be caused by
power lines, electric fences, traffic lights and
thunderstorms.
*
[AS07915(ALL)08/95]
Another reception phenomenon isStrong Signal
Capture and Overload. This can occur when
listening to a weak station and when passing
another broadcast tower. The close station may
capture the more distant station, although the
displayed frequency does not change. While
passing the tower, the station may switch back
and forth a few times before returning to the
original station.
*
[AS07920(ALL)08/95]
When several broadcast towers are present
(common in metropolitan areas) several stations
may overload the receiver, resulting in
considerable station changing, mixing and
distortion.
*
[AS07925(ALL)08/95]
Automatic gain control circuitry for both AM
and FM bands has been incorporated into this
system to reduce strong signal capture and
overload.
File:09cpasa.ex
Update:Tue Aug 29 17:42:51 1995
Page 173 of 353
192 [DR16025(ALL)05/94]How the Electronic 4-Wheel Drive (E-4WD)
System Works
[DR16036(ALL)03/90]
Under normal driving conditions, when the road
is firm, dry and level, the engine power is
distributed one-third to the front axle and
two-thirds to the rear axle. However, if a wheel
begins to slip, the microprocessor will sense this
condition and signal the system to transmit more
power to the axle with more traction. (You may
feel a momentary surge of power.)
[DR16046(ALL)06/95]
NOTE: The microprocessor is disabled when
the brakes are applied or when the
transmission selector is in the P (Park)
or N (Neutral) positions.
[DR16055(ALL)05/94]
Driving Your Electronic 4-Wheel Drive
(E-4WD) Vehicle
[DR16065(ALL)03/95]
Since your E-4WD vehicle is unique, follow these
steps to be safe:
[DR16075(ALL)03/95]
q
Avoid unnecessary turns or other maneuvers
that could cause loss of control and possible
injury.
[DR16076(ALL)06/95]
q
Use the same size and type of tire and wheel
as originally provided for your vehicle and
inflate the tires to the manufacturer's
recommended air pressure.
[DR16077(ALL)03/95]
q
Become familiar with your vehicle's operating
characteristics and study this Owner Guide
for specific operating instructions. Be sure all
occupants wear the safety belts provided.
Drive cautiously, defensively, and at speeds
safe for current road conditions.
File:10cpdra.ex
Update:Tue Aug 29 17:45:28 1995
Page 300 of 353
322 %
*
[SV44100(ALL)03/95]
Circuit Breakers
[SV44200(ALL)08/95]
If you need to check a circuit breaker, locate the
fuse panel first. Otherwise, locate the circuit
breaker according to the instructions on the
charts given earlier in this chapter.
*
[SV44400(ALL)10/92]
However, you should know that the circuit
breakers will reset themselves and allow the
electrical parts to work again once the overload
on the circuit is removed. If the circuit breakers
continue to cut off electricity, have your vehicle's
electrical system checked.
*
[SV44450(ALL)02/95]
Diagnostic equipment is needed to check circuit
breakers. Refer to the manufacturer's
instructions.
[SV44500(ALL)08/95]
If you replace a circuit breaker, use one with the
same amperage rating. To remove a circuit
breaker, grip it with your finger and thumb and
pull it straight out of its socket.
%
*
[SV44600(ALL)03/95]
Lights and Bulb Replacement
*
[SV44700(ALL)01/95]
It is a good idea to check the operation of the
following lights frequently:
*
[SV44800(ALL)01/95]
q
headlamps
*
[SV44850(ALL)02/95]
q
high-mount brakelamp
*
[SV44900(ALL)01/95]
q
tail lamps
*
[SV45000(ALL)01/95]
q
brakelamps
*
[SV45100(ALL)01/95]
q
hazard flasher
*
[SV45200(ALL)01/95]
q
turn signals
*
[SV45300(ALL)01/95]
q
license plate lamp
File:15cpsva.ex
Update:Tue Aug 29 17:51:51 1995
Page 301 of 353
323 %
*
[SV45400(ALL)01/95]
The alignment of your headlamps should be
checked if:
*
[SV45500(ALL)01/95]
q
oncoming motorists frequently signal you to
turn off your vehicle's high beams when you
do not have the high beams on
*
[SV45600(ALL)01/95]
q
the headlamps do not seem to give you
enough light to see clearly at night
*
[SV45700(ALL)01/95]
q
the headlamp beams are pointed substantially
away from a position slightly down and to
the right
%*
[SV45800(ALL)03/95]
Headlamp Bulb
*
[SV45900(ALL)01/95]
The headlamps on your vehicle use replaceable
bulbs. When the lamp burns out, simply replace
the bulb, rather than the whole lamp.
*
[SV46000(ALL)05/95]
RWARNING
Handle a halogen headlamp bulb carefully
and keep out of children's reach. Grasp
the bulb only by its plastic base and do
not touch the glass. The oil from your
hand could cause the bulb to break the
next time the headlamps are operated.
*
[SV46050(ALL)12/91]
NOTE: If the bulb is accidently touched, it
should be cleaned with rubbing
alcohol before being used.
*
[SV46100(ALL)01/95]
Do not remove the burned-out bulb unless you
can immediately replace it with a new one. If a
bulb is removed for an extended period of time,
contaminants may enter the headlamp housing
and affect its performance.
File:15cpsva.ex
Update:Tue Aug 29 17:51:51 1995