wiring FORD AEROSTAR 1996 1.G Owners Manual

28
*
[SR11600(ALL)08/95]
RWARNING
If a passenger is not properly seated and
restrained, an inflating air bag could cause
serious injury.
*
[SR11640(ALL)07/95]
RWARNING
Do not place objects or mount equipment
on or near the air bag cover on the
steering wheel or in front seat areas that
may come in contact with a deploying air
bag. Failure to follow this instruction may
increase the risk of personal injury in the
event of a collision.
*
[SR11650(ALL)07/95]
For further information about the proper
mounting of equipment in the front seat of this
vehicle, please refer to Ford's brochure entitled
Some Important Information About Air Bag
Supplemental Restraint Systemwhich can be
obtained by calling Helm Inc. at 1-800-782-4356.
Ask for brochure FPS-8602.
*
[SR11660(ALL)08/95]
For additional important safety information on
the proper use of seat belts, child seats, and
infant seats, please read the other sections of this
chapter of the Owner Guide, especially sections
entitledSafety Belts for ChildrenandSafety Seats
for Children.
%*
[SR11800(ALL)01/95]
How the Air Bag Supplemental Restraint
System Operates
[SR11850(ALL)05/95]
The Air Bag Supplemental Restraint System
consists of the driver air bag, impact sensor, a
system diagnostic module, a readiness light and
tone, and the electrical wiring which connects
the components.
File:03cpsra.ex
Update:Tue Aug 29 17:35:04 1995

219 %
*
[DR37800(ALL)07/95]
Safety Chains
*
[DR37900(ALL)12/92]
Always use safety chains between your vehicle
and trailer. Cross chains under the trailer tongue
and allow slack for turning corners. Connect
safety chains to the vehicle frame or hook
retainers. Never attach chains to the bumper.
%*
[DR38000(ALL)08/95]
Trailer Brakes
*
[DR38100(ALL)03/95]
Separate trailer brakes are required on most
towed vehicles weighing over 1,500 lb (680 kg).
*
[DR38200(ALL)05/95]
RWARNING
Do not connect a trailer's hydraulic brake
system directly to your vehicle's brake
system. Your vehicle may not have
enough braking power and your chances
of having a collision greatly increase.
%*
[DR38300(ALL)06/95]
Trailer Lamps
*
[DR38400(ALL)11/89]
Make sure your trailer lamps conform to Federal
and local regulations.
*
[DR38425(ALL)03/91]
Class I and Class II Trailer Tow electrical wiring
provides two circuits (right hand and left hand)
to operate trailer stop/turn tail lamps. Each
stop/turn circuit will operate one combination
stop/turn light bulb (# 1157, 3157, 2357, or 3357)
on the trailer. Never add more than one trailer
light bulb to one circuit.
*
[DR38450(ALL)05/95]
RWARNING
Always replace a fuse with one that has
the specified amperage rating. Using a
fuse with a higher amperage rating can
cause severe wire damage and could start
a fire.
File:10cpdra.ex
Update:Tue Aug 29 17:45:28 1995

303 [SV31625(ALL)03/95]
q
Put the chains on tightly with the ends held
down securely. Verify that no chain touches
any wiring, brake lines or fuel lines.
Retighten the chains after driving 1/2 mile
(0.8 km). Follow the chain manufacturer's
instructions.
*
[SV31650(ALL)07/94]
q
Do not drive faster than 30 mph (48 km/h)
or the chain manufacturer's recommended
speed limit, whichever is lower. Avoid
bumps, holes and sharp turns. If you can
hear the chains rub or bang against your
vehicle, remove the chains to prevent damage
to your vehicle.
*
[SV31750(ALL)11/94]
q
Tire chains may affect vehicle handling. Drive
carefully and avoid hard braking.
*
[SV31800(ALL)10/94]
q
Avoid fully loading your vehicle if possible.
*
[SV31900(ALL)05/94]
q
Remove tire chains at the first opportunity
after using them on snow and ice. Do not use
the chains on dry roads.
*
[SV31950(ALL)05/91]
q
Make sure your suspension insulation and
bumpers are not missing or worn to avoid
damage to your vehicle.
%*
[SV31960(ALL)04/95]
Cleaning the Wheels
*
[SV31965(ALL)05/95]
Wash the wheels with the same detergent you
use to wash your vehicle's body. Do not use
acid-based wheel cleaners, steel wool, abrasives,
fuel, or strong detergents. These substances will
damage protective coatings. Use tar and road oil
remover to remove grease and tar.
*
[SV31967(ALL)04/95]
NOTE: Before going to a car wash, find out if
the brushes are abrasive.
File:15cpsva.ex
Update:Tue Aug 29 17:51:51 1995

326 [SV47310(ALL)08/95]Removing the High-Mount Brakelamp
Bulb
[SV47315(ALL)05/94]
Liftgate models
[SV47317(ALL)08/95]
To remove the brakelamp and bulb:
*
[SV47330(ALL)03/93]
1. Remove the two screws from the surface of
the lens.
*
[SV47340(ALL)03/93]
2. After removing the screws, remove the lamp
assembly.
[SV47353(ALL)07/93]
3. Disconnect the high-mount brakelamp wiring
connector.
[SV47356(ALL)03/93]
4. Remove the screw retaining the bulb holder
assembly, pull the bulb holder assembly
away from the lamp, and pull the bulb
straight out of the holder.
*
[SV47360(ALL)03/95]
To replace/install the brakelamp:
[SV47367(ALL)03/93]
1. Push bulb(s) into bulb holder assembly.
[SV47373(ALL)03/93]
2. Place bulb holder assembly on lamp and
install retaining screw. Tighten screw.
[SV47376(ALL)07/93]
3. Connect the high-mount brakelamp wiring
connector.
[SV47377(ALL)03/93]
4. Position the lamp assembly on the vehicle.
[SV47378(ALL)03/93]
5. Install and tighten the two screws.
[SV47380(ALL)08/95]
6. Apply brakes to confirm the brakelamp is
functional after installing.
File:15cpsva.ex
Update:Tue Aug 29 17:51:51 1995