ignition FORD AEROSTAR 1997 1.G Owner's Guide

161 [TO10800(ALL)01/96]
q
AIR CONDITIONING Ð Set the fan speed
knob at MEDIUM or HIGH, the function
selector knob on NORM A/C or MAX A/C
and the temperature control knob on any
desired position.
*
[TO12000(ALL)03/96]
Removing the Key From the
Ignition
*
[TO12100(ALL)03/96]
1. Put the gearshift in P (Park).
*
[TO12200(ALL)03/96]
2. Set the parking brake fully before removing
your foot from the service brake. (This will
avoid ªbindingº or ªloadingº the park gear
if you park on a grade.)
*
[TO12300(ALL)03/96]
3. Turn the ignition key to LOCK.
*
[TO12400(ALL)03/96]
4. Remove the key.
*
[TO12500(ALL)05/96]
RWARNING
Always set the parking brake fully and
make sure the gearshift is latched in P
(Park). Turn off the ignition whenever you
leave your vehicle.
*
[TO12600(ALL)03/96]
RWARNING
Do not leave children, unreliable adults,
or pets unattended in your vehicle.
File:08cptoa.ex
Update:Thu Jun 6 14:43:40 1996

167 [GF02000(ALL)01/96]
quarter page art:0020566-A
Parking Brake
*
[GF02100(ALL)05/96]
RWARNING
Always set the parking brake fully and
make sure the gearshift is latched in P
(Park). Turn off the ignition whenever you
leave your vehicle.
*
[GF02200(ALL)02/96]
RWARNING
If the parking brake is fully released, but
the Brake System light remains on, have
the brakes checked immediately. They
may not be working properly.
*
[GF02250(ALL)03/96]
The parking brake is not designed to stop a
moving vehicle, but you can use the parking
brake to stop your vehicle in an emergency if
the normal brakes fail. However, since the
parking brake applies only the rear brakes, the
stopping distance will increase greatly and the
handling of your vehicle will be adversely
affected.
File:09cpgfa.ex
Update:Wed Jun 5 12:04:06 1996

171 [GF10920(ALL)06/96]
one third page art:0095028-A
*
[GF11000(ALL)05/96]
RWARNING
Hold the brake pedal down while you
move the gearshift lever from position to
position. If you do not hold the brake
pedal down, your vehicle may move
unexpectedly and injure someone.
*
[GF12000(ALL)05/96]
Once you place the gearshift securely into
position, gradually release the brake pedal and
use the accelerator as necessary.
%*
[GF12100(ALL)05/96]
NOTE: Your vehicle is equipped with a
brake-shift interlock feature. This
feature prevents you from shifting
from P (Park) unless you have the
brake pedal depressed. (The ignition
must be in the ON position.) If you
cannot shift from P (Park) with the
brake pedal depressed:
*
[GF12200(ALL)05/96]
1. Apply the parking brake.
*
[GF12300(ALL)05/96]
2. Remove the key.
*
[GF12400(ALL)05/96]
3. Insert the key and rotate it one position
clockwise (ignition in the OFF position).
File:09cpgfa.ex
Update:Wed Jun 5 12:04:06 1996

172
*
[GF12500(ALL)05/96]
4. Apply the brake pedal and shift to N
(Neutral). (If the vehicle is shifted back to P
[Park], you must repeat the previous steps.)
*
[GF12600(ALL)05/96]
5. Start the vehicle.
*
[GF12700(ALL)05/96]
If you need to shift out of P (Park) by using the
alternate procedure described above, it is
possible that a fuse has blown and that your
brakelamps may also not be functional. Please
refer to the chapter titledRoadside Emergenciesin
this Owner Guide for instructions on checking
and replacing fuses.
*
[GF12800(ALL)05/96]
RWARNING
DO NOT DRIVE YOUR VEHICLE UNTIL
YOU VERIFY THAT THE BRAKELAMPS
ARE WORKING.
*
[GF12820(ALL)05/96]
P (Park)
[GF12830(ALL)03/96]
Always come to a complete stop before you shift
into P (Park). This position locks the
transmission and prevents the rear wheels from
turning.
[GF12840(ALL)03/96]
To securely latch the gearshift in the P (Park)
position, pull it toward you, push it completely
counterclockwise against the stop, and then push
it toward the instrument panel.
*
[GF12850(ALL)06/96]
The gearshift is securely latched in P (Park) if
you cannot rotate it in a clockwise direction
without lifting it toward you.
*
[GF12860(ALL)05/96]
RWARNING
Always set the parking brake fully and
make sure the gearshift is latched in P
(Park). Turn off the ignition whenever you
leave your vehicle.
File:09cpgfa.ex
Update:Wed Jun 5 12:04:06 1996

173
*
[GF12870(ALL)05/96]
RWARNING
Never leave your vehicle unattended
while it is running.
%*
[GF12900(ALL)05/96]
R (Reverse)
*
[GF12950(ALL)05/96]
With the gearshift in the R (Reverse) position,
the vehicle will move backward. You should
always come to a complete stop before shifting
into or out of R (Reverse).
*
[GF12975(ALL)01/96]
N (Neutral)
*
[GF12990(ALL)06/96]
With the gearshift in the N (Neutral) position,
the vehicle can be started and is free to roll.
Hold the brake pedal down while in this
position.
*
[GF12995(ALL)06/96]
RWARNING
Do not leave the vehicle unattended with
the transfer case in the N (Neutral)
position. Always set the parking brake
fully and turn off the ignition when
leaving the vehicle.
*
[GF13000(ALL)06/96]
With the transfer case in N (Neutral), the vehicle
is free to move with either the automatic
transmission in P (Park) or with the manual
transmission in any driving gear.
[GF13050(ALL)03/96]
Driving (4R44E Transmission)
%*
[GF13100(ALL)05/96]
When to usej(Overdrive)
*
[GF13150(ALL)05/96]
This is the normal driving position. As the
vehicle picks up speed, automatic upshifts to
second, third and fourth gears will occur when
jOverdrive is chosen on the selector and the
transmission control switch has not been
pressed. The transmission will shift into the
correct gear when the right speed is achieved,
for the accelerator pedal position you have
chosen.
File:09cpgfa.ex
Update:Wed Jun 5 12:04:06 1996

209 %
*
[ER00510(ALL)05/96]
Circuit Breakers
[ER00515(ALL)01/96]
If you need to check a circuit breaker, locate the
fuse panel first. Otherwise, locate the circuit
breaker according to the instructions on the
charts given earlier in this chapter.
*
[ER00520(ALL)01/96]
However, you should know that the circuit
breakers will reset themselves and allow the
electrical parts to work again once the overload
on the circuit is removed. If the circuit breakers
continue to cut off electricity, have your vehicle's
electrical system checked.
*
[ER00525(ALL)01/96]
Diagnostic equipment is needed to check circuit
breakers. Refer to the manufacturer's
instructions.
[ER00530(ALL)01/96]
If you replace a circuit breaker, use one with the
same amperage rating. To remove a circuit
breaker, grip it with your finger and thumb and
pull it straight out of its socket.
%
*
[ER03600(ALL)02/96]
Changing a Tire
*
[ER03700(ALL)02/96]
If you get a flat tire while you are driving, do
not apply the brake heavily. Instead, gradually
decrease the speed. Hold the steering wheel
firmly and slowly move to a safe place on the
side of the road. Park on a level spot, turn off
the ignition, set the parking brake, and turn on
the hazard flashers.
%*
[ER03800(ALL)01/96]
The Conventional Spare Tire
*
[ER03900(ALL)05/96]
If you have the conventional spare tire, you can
use it as a spare or as a regular tire. This spare
tire is identical to the other tires that come with
your vehicle, although the wheel may not match.
File:10cpera.ex
Update:Thu Jun 6 14:45:00 1996

216 [ER07600(ALL)01/96]
half page art:0020270-AExtended van underbody outside spare wheel/flat tire
storage
*
[ER15100(ALL)01/96]
RWARNING
Make sure the spare tire and jacking
equipment are stowed and secured in the
proper storage location.
%*
[ER15200(ALL)03/96]
Preparing to Change the Tire
*
[ER15250(ALL)01/96]
NOTE: To lift your vehicle by other than the
front or rear jacking points, be sure to
use only hoist adapters with a wide
contact surface.
*
[ER15325(ALL)03/96]
1. Make sure that your vehicle will not move
or roll. Put the gearshift in P (Park). Set the
parking brake and block the wheel that is
diagonally opposite the tire that you are
changing.
*
[ER15335(ALL)01/96]
NOTE: Make sure the ignition is in the OFF
position.
File:10cpera.ex
Update:Thu Jun 6 14:45:00 1996

223 %
*
[ER24440(ALL)02/96]
RWARNING
Applying too much pressure on the ends
when lifting a battery could cause acid to
spill. Lift the battery with a carrier or
with your hands on the opposite corners.
%*
[ER24450(ALL)05/96]
RWARNING
Batteries contain sulfuric acid which burns
skin, eyes, and clothing.
*
[ER24460(ALL)02/96]
If the acid touches someone's skin, eyes, or
clothing, immediately flush the area with water
for at least 15 minutes. If someone swallows the
acid, have him or her drink lots of milk or water
first, then Milk of Magnesia, a beaten egg, or
vegetable oil. Call a doctor immediately.
*
[ER24470(ALL)01/96]
RWARNING
Do not push-start your vehicle. You could
damage the catalytic converter. For further
information, seeJumper Cablesin the
Index.
*
[ER24480(ALL)02/96]
To avoid damaging your vehicle or your battery,
and to avoid injury to yourself, follow these
directions for preparing your vehicle to
jump-start and connecting the jumper cables in
the order they are given. If in doubt, call for
road service.
%*
[ER24490(ALL)02/96]
Preparing Your Vehicle
*
[ER24500(ALL)02/96]
1. Your vehicle has a 12-volt starting system, so
you need to use a 12-volt jumper system.
You will damage your starting motor,
ignition system, and other electrical parts if
you connect them to a 24-volt power supply
(either two 12-volt batteries in series or a
24-volt generator set).
File:10cpera.ex
Update:Thu Jun 6 14:45:00 1996

226 %
*
[ER24660(ALL)02/96]
Removing jumper cables
*
[ER24670(ALL)02/96]
1.Always remove the jumper cables in the
reverse order.Remove the negative (S) end
of the jumper cable from the metallic surface
on the engine or frame of the disabled
vehicle.
*
[ER24680(ALL)03/96]
2. Remove the negative (S) cable from the
booster battery.
*
[ER24690(ALL)02/96]
3. Remove the positive (+) cable from the
booster battery.
*
[ER24692(ALL)02/96]
4. Remove the other end of the positive (+)
cable from the discharged battery.
*
[ER24694(ALL)02/96]
After the vehicle is started, let it idle for a while
to let the engine ªrelearnº its idle conditions.
Drive it around for a while with all electrical
accessories turned off to let the battery recharge.
Driveability may be deteriorated slightly until all
drive modes are ªrelearned.ºYou may need to
use a battery charger to fully recharge the
battery.
*
[ER24695(ALL)03/96]
If you need to replace your battery, seeBattery
in theMaintenance and Carechapter.
%
*
[ER24700(ALL)04/96]
Towing Your Vehicle
[ER24750(ALL)01/96]
The recommended method to tow your Aerostar
is with flatbed or wheel lift equipment.
However, slingbelt towing is acceptable. On
vehicles equipped with an under-vehicle spare
tire carrier, remove the tire assembly from the
carrier and store it in a secure area before
towing. For E-4WD vehicles, the 4-wheel drive
system must be disabled prior to towing. The
transmission must be in N (Neutral) and the
ignition switch must be in the OFF position to
disable the Electronic 4-Wheel Drive System.
File:10cpera.ex
Update:Thu Jun 6 14:45:00 1996

231
*
[MC02500(ALL)01/96]
If you disconnect the battery, the engine must
ªrelearnº its idle conditions before your vehicle
will drive properly. To find out how the engine
does this, seeBatteryin this chapter.
*
[MC02600(ALL)01/96]
Working with the engine off:
*
[MC02650(ALL)01/96]
1. Set the parking brake fully and make sure
that the gearshift is securely latched in P
(Park).
*
[MC02700(ALL)01/96]
2. Remove the key from the ignition after you
turn the engine off.
*
[MC02725(ALL)01/96]
3. Block the wheels. This will prevent your
vehicle from moving unexpectedly.
*
[MC02750(ALL)01/96]
Working with the engine on:
*
[MC02785(ALL)01/96]
1. Set the parking brake fully and make sure
that the gearshift is securely latched in P
(Park).
*
[MC02800(ALL)01/96]
2. Block the wheels. This will prevent your
vehicle from moving unexpectedly.
*
[MC02900(ALL)01/96]
RWARNING
Do not start your engine with the air
cleaner removed and do not remove it
while the engine is running.
%*
[MC02950(ALL)02/96]
Opening the Hood
*
[MC03000(ALL)01/96]
1. Pull the hood release handle, located next to
the parking brake pedal.
File:11cpmca.ex
Update:Fri Jun 7 14:30:56 1996