brake fluid FORD ASPIRE 1996 1.G Owners Manual
[x] Cancel search | Manufacturer: FORD, Model Year: 1996, Model line: ASPIRE, Model: FORD ASPIRE 1996 1.GPages: 268, PDF Size: 2.2 MB
Page 209 of 268
210 [SV29850(ALL)02/95]Checking the Automatic Transaxle Fluid
*
[SV29900(ALL)02/95]
With the vehicle on a level surface and the brake
pedal fully applied, start the engine and move
the gearshift selector through all of the gears.
Allow sufficient time for each position to engage.
Securely latch the gearshift selector in the P
(Park) position. Fully set the parking brake and
leave the engine running.
[SV29925(ALL)03/94]
Pull the dipstick out and wipe the indicator end
clean. Put the dipstick back into the filler tube
and make sure it is fully seated; otherwise, you
will not get an accurate reading. Pull the
dipstick out and read the fluid level.
[SV29950(ALL)03/94]
one third page art:0032228-B
Automatic transaxle fluid dipstick
[SV30000(ALL)05/93]
The fluid level must be above the ªLº mark. If it
is not, you should not drive your vehicle until
more fluid is added. Ideally, the fluid level
should be within the specified area of the
dipstick.
File:15icsvf.ex
Update:Wed Jan 24 14:56:41 1996
Page 211 of 268
212 [SV31300(ALL)08/91]
half page art:0030228-BChecking manual transaxle oil level
%*
[SV31350(ALL)04/95]
NOTE: Always dispose of used automotive
fluids in a responsible manner. Follow
your community's standards for
disposing of these types of fluids. Call
your local recycling center to find out
about recycling automotive fluids.
*
[SV31600(ALL)03/95]
Brake Fluid
*
[SV31700(ALL)03/95]
Under normal circumstances, your vehicle
should not use up brake fluid rapidly. However,
expect the level of the brake fluid to slowly fall
as you put more mileage on your vehicle and
the brake pads wear.
[SV31800(ALL)09/93]
Check the brake fluid at least once a year. You
can do this by looking at the fluid level in the
plastic reservoir on the master cylinder. (See
Your Engine Typeearlier in this chapter to locate
the master cylinder.) The fluid level should be at
or near the MAX mark.
File:15icsvf.ex
Update:Wed Jan 24 14:56:41 1996
Page 212 of 268
213
*
[SV31850(ALL)05/95]
RWARNING
Brake fluid is toxic.
*
[SV31860(ALL)07/95]
If brake fluid contacts eyes, flush eyes with
running water for 15 minutes. Get medical
attention if irritation persists. If taken internally,
drink water and induce vomiting. Get medical
attention immediately.
[SV31900(ALL)08/91]
one third page art:0030229-A
Brake fluid level
[SV32100(ALL)03/95]
If the fluid is low, carefully clean and remove
the cap from the reservoir. Fill the reservoir to
the MAX line with Ford High Performance DOT
3 Brake Fluid C6AZ-19542-AA, C6AZ-19542-BA,
or equivalent DOT 3 fluid meeting Ford
specification ESA-M6C25-A.
*
[SV32400(ALL)01/95]
RWARNING
If you use a brake fluid that is not DOT
3, you will cause permanent damage to
your brakes.
*
[SV32500(ALL)01/95]
Do not fill the reservoir above the MAX line.
*
[SV32600(ALL)01/95]
If you find that the fluid level is excessively low
Ð below the seam or ridge on the outside of the
plastic reservoir Ð have the brake system
inspected.
File:15icsvf.ex
Update:Wed Jan 24 14:56:41 1996
Page 213 of 268
214
*
[SV32700(ALL)01/95]
RWARNING
Do not let the reservoir for the master
cylinder run dry. This may cause the
brakes to fail.
*
[SV32800(ALL)03/95]
Power Steering Fluid
*
[SV32900(ALL)01/95]
Check the level of the power steering fluid at
least twice a year (i.e., every Spring and Fall).
*
[SV33000(ALL)03/95]
Checking and Adding Power Steering
Fluid
*
[SV33100(ALL)02/95]
1. Start the engine and let it run until the
power steering fluid reaches normal
operating temperature. The power steering
fluid will be at the right temperature when
the engine coolant temperature gauge in the
instrument cluster is near the center of the
NORMAL operating temperature range.
*
[SV33200(ALL)01/95]
2. While the engine idles, turn the steering
wheel back and forth several times. Make
sure that the cap assembly is installed at this
time.
*
[SV33300(ALL)05/95]
3. Turn the engine off.
[SV33400(ALL)07/93]
4. Check the fluid level on the reservoir. The
fluid level should be at the F (Full) line on
the reservoir.
File:15icsvf.ex
Update:Wed Jan 24 14:56:41 1996