key FORD ASPIRE 1996 1.G Owners Manual
[x] Cancel search | Manufacturer: FORD, Model Year: 1996, Model line: ASPIRE, Model: FORD ASPIRE 1996 1.GPages: 268, PDF Size: 2.2 MB
Page 26 of 268
24 %
*
[SR13500(ALL)05/95]
The air bag system uses a readiness light on the
instrument cluster and a tone to indicate the
condition of the system. When you turn the
ignition key to the ON position, this light will
illuminate for approximately six (6) seconds and
then turn off. This indicates that the system is
operating normally. NOTE: Maintenance of the
air bag system is not required.
%*
[SR13700(ALL)06/95]
A problem with the system is indicated by one
or more of the following:
*
[SR13800(ALL)06/95]
q
the readiness light will either flash or stay lit,
*
[SR13900(ALL)06/95]
q
or it will not light immediately after ignition
is turned on,
*
[SR14000(ALL)06/95]
q
or a group of five beeps will be heard. The
tone pattern will repeat periodically until the
problem and light are repaired.
*
[SR14100(ALL)07/95]
If any of these things happen, have the air bag
system serviced at your Ford or Lincoln-Mercury
dealer immediately. Unless serviced, the air bag
Supplemental Restraint System may not function
properly in the event of a collision.
*
[SR14400(ALL)05/95]
RWARNING
Do not attempt to service, repair, or
modify the Air Bag Supplemental
Restraint System or its fuses. See your
Ford or Lincoln-Mercury dealer.
%*
[SR15225(ALL)05/95]
Disposal of air bags or air bag equipped
vehicles
*
[SR15240(ALL)06/95]
For disposal of air bags or air bag equipped
vehicles, see your local Ford or Lincoln-Mercury
dealer. Air bagsMUSTbe disposed of by
qualified personnel.
File:03icsrf.ex
Update:Wed Jan 24 14:30:01 1996
Page 44 of 268
42
*
[ST02100(ALL)09/93]
LOCK locks the steering wheel. It also locks the
gearshift lever in P (Park) (automatic transaxle).
*
[ST02200(ALL)01/95]
LOCK is the only position that allows you to
remove the key. The LOCK feature helps to
protect your vehicle from theft.
*
[ST02300(ALL)05/95]
If your key is stuck in the LOCK position and
will not turn, move your steering wheel left or
right until the key turns freely.
[ST02325(ALL)09/93]
If your vehicle has a manual transaxle, you must
push the key toward the steering column to
rotate the switch to the LOCK position.
%*
[ST02350(ALL)03/95]
ACC (accessory) allows some of your vehicle's
electrical accessories such as the radio and the
windshield wipers to operate while the engine is
not running.
*
[ST02400(ALL)05/95]
ON allows you to test your vehicle's warning
lights (except the brake system warning light) to
make sure they work before you start the
engine. The key returns to the ON position once
the engine is started and remains in this position
while the engine runs.
*
[ST02500(ALL)03/95]
START cranks the engine. Release the key once
the engine starts so that you do not damage the
starter. The key should return to ON when you
release it. The START position also allows you
to test the brake warning light.
File:04icstf.ex
Update:Wed Jan 24 14:30:41 1996
Page 45 of 268
43
*
[ST02505(ALL)09/93]
Shift-lock System
*
[ST02510(ALL)07/95]
For your safety, the optional automatic transaxle
has a shift-lock system, which prevents shifting
the transaxle out of the P (Park) position without
depressing the brake pedal when the ignition
key is in the ON position.
*
[ST02515(ALL)07/89]
To shift the transaxle out of the P (Park)
position:
*
[ST02521(ALL)05/90]
1. Depress and hold the brake pedal.
*
[ST02526(ALL)11/93]
2. Start the engine.
[ST02528(ALL)02/92]
3. Push in the thumb lock button and move the
gearshift lever.
[ST02529(ALL)07/93]
4. SeeEmergency Override Systemlater in this
section for more information.
*
[ST02535(ALL)09/93]
NOTE: When the ignition key is in the ACC
or LOCK position, the transaxle cannot
be shifted from the P (Park) position.
If the brake pedal is repeatedly
depressed and released when the
ignition is in the ON position and the
selector lever is in the P (Park)
position, a chattering near the gearshift
lever may be heard. This is not a
malfunction.
*
[ST02538(ALL)03/94]
NOTE: Your vehicle's gearshift lever is
securely latched in P (Park) if you
cannot move it without pushing in the
thumb button. Keep the brake pedal
depressed while moving your gearshift
lever.
*
[ST02540(ALL)09/93]
To make the system more effective, the ignition
key cannot be removed unless the gearshift
selector lever is in the P (Park) position.
File:04icstf.ex
Update:Wed Jan 24 14:30:41 1996
Page 47 of 268
45
*
[ST02820(ALL)06/93]
3. Push and hold the thumb button.
[ST02830(ALL)09/93]
4. Move the gearshift lever.
*
[ST02832(ALL)07/95]
If you need to shift out of P (Park) by using the
alternate procedure described above, it is
possible that a fuse has blown and that your
brakelamps may also not be functional. Please
refer to the chapter titledServicing Your Aspirein
this Owner Guide for instructions on checking
and replacing fuses.
*
[ST02835(ALL)05/95]
RWARNING
DO NOT DRIVE YOUR VEHICLE UNTIL
YOU VERIFY THAT THE BRAKELAMPS
ARE WORKING.
%*
[ST02850(ALL)03/95]
Ignition Key Chime
*
[ST02875(ALL)10/90]
If the driver or passenger door is open while the
key is still in the ignition, a warning chime
sounds.
%*
[ST02900(ALL)02/95]
Removing the Key From the Ignition
*
[ST03000(ALL)09/93]
1. Put the gearshift selector lever in P (Park)
(automatic transaxle) or 1 (First) (manual
transaxle).
*
[ST03100(ALL)01/95]
2. Set the parking brake fully.
[ST03450(ALL)12/93]
3. Push the key in (manual transaxle) and turn
it to the LOCK position.
*
[ST03500(ALL)03/95]
4. Remove the key.
*
[ST03700(ALL)06/95]
RWARNING
Always set the parking brake fully and
make sure that the gearshift is securely
latched in P (Park) (automatic transaxle) or
in 1 (First) (manual transaxle).
File:04icstf.ex
Update:Wed Jan 24 14:30:41 1996
Page 49 of 268
47
*
[ST04500(ALL)03/95]
Starting Your Vehicle
%*
[ST05000(ALL)05/94]
Preparing to Start Your Vehicle
*
[ST05100(ALL)05/95]
RWARNING
Do not start your vehicle in a closed
garage or other enclosed area. Never sit in
a stopped vehicle for more than a short
period of time with the engine running.
Exhaust fumes are toxic. SeeGuarding
Against Exhaust Fumesin this chapter for
more instructions.
*
[ST05200(ALL)01/95]
Before you start your vehicle, do the following:
*
[ST05300(ALL)07/95]
1. Make sure all occupants in the vehicle
buckle their safety belts. SeeSafety Restraints
in the Index for more details.
*
[ST05400(ALL)03/95]
2. Make sure the headlamps and other
accessories are turned off when starting.
*
[ST05500(ALL)02/92]
3.If you have an automatic transaxle, make
sure that the gearshift is in P (Park) and the
parking brake is set before you turn the key.
*
[ST05600(ALL)07/93]
If you have a manual transaxle, make sure
that the parking brake is fully set, push the
clutch pedal to the floor, and put the
gearshift into Neutral before you turn the
key.(Remember, the starter will operate
only if the clutch pedal is pushed all the
way to the floor.)
*
[ST05800(ALL)03/95]
Before you start your vehicle, you should test
the warning lights on the instrument panel to
make sure that they work. Refer to theWarning
Lights and Gaugeschapter.
File:04icstf.ex
Update:Wed Jan 24 14:30:41 1996
Page 50 of 268
48 [ST05850(ALL)07/95]To test the brake warning light, release the
parking brake and turn the ignition key to the
START position. The brake warning light should
illuminate until the key is released. See the
Warning Lights and Gaugeschapter for additional
information.
[ST05900(ALL)07/95]
After starting the engine, check all the warning
lights to make sure that they are off. If any one
of them is still lit, it indicates a situation that
needs your attention. When you release the
parking brake, the brake warning light should
go off.
*
[ST06000(ALL)02/95]
Starting Your Engine
*
[ST06100(ALL)06/95]
To start your engine:
*
[ST06300(ALL)03/95]
1. Follow the steps underPreparing to Start
Your Vehicleand underTesting the Warning
Lightsat the beginning of this section.
*
[ST06320(ALL)03/95]
2. Keep your foot on the brake pedal and turn
the ignition key to the ON position.
*
[ST06330(ALL)06/95]
3. DO NOT depress the accelerator pedal when
starting your engine. DO NOT use the
accelerator while the vehicle is parked.
*
[ST06340(ALL)02/95]
4. Turn the key to the START position
(cranking) until the engine starts. Allow the
key to return to the ON position after the
engine has started.
*
[ST06400(ALL)02/95]
If you have difficulty in turning the key,
rotate the steering wheel slightly because it
may be binding.
File:04icstf.ex
Update:Wed Jan 24 14:30:41 1996
Page 51 of 268
49 %
*
[ST06800(ALL)04/95]
For a cold engine:
*
[ST06810(ALL)06/95]
q
At temperatures10ÊF (-12ÊC) andbelow:If
the engine does not start infifteen (15)
secondson the first try, turn the key to OFF,
wait approximately ten (10) seconds so you
do not flood the engine, then try again.
*
[ST06820(ALL)04/95]
q
At temperaturesabove10ÊF(-12ÊC):If the
engine does not start infive (5) secondson
the first try, turn the key to OFF, wait
approximately ten (10) seconds so you do not
flood the engine, then try again.
%*
[ST06830(ALL)05/95]
For a warm engine:
*
[ST06840(ALL)04/95]
q
Do not hold the key in the START position
for more thanfive (5) secondsat a time. If
the engine does not start within five (5)
seconds on the first try, turn the key to the
OFF position. Wait a few seconds after the
starter stops, then try again.
*
[ST06843(ALL)07/95]
Whenever you start your vehicle, release the key
as soon as the engine starts. Excessive cranking
could damage the starter.
*
[ST06845(ALL)05/95]
After starting, allow the engine to idle for a few
seconds before driving away.
*
[ST06847(ALL)05/95]
NOTE: Automatic transaxle equipped vehicles
have an interlock that prevents you
from shifting out of P (Park) unless
your foot is on the brake pedal.
%*
[ST06860(ALL)04/95]
If the engine does not start after two attempts:
*
[ST06865(ALL)04/95]
1. Turn the ignition key to the OFF position.
*
[ST06870(ALL)04/95]
2. Press the accelerator all the way to the floor
and hold it.
File:04icstf.ex
Update:Wed Jan 24 14:30:41 1996
Page 52 of 268
50
*
[ST06875(ALL)04/95]
3. Turn the ignition key to the START position.
*
[ST06880(ALL)04/95]
4. Release the ignition key when the engine
starts.
*
[ST06885(ALL)04/95]
5. Release the accelerator gradually as the
engine speeds up. Then drive away in the
normal manner.
*
[ST06890(ALL)04/95]
If the engine still does not start, the fuel pump
shut-off switch may have been triggered. For
directions on how to reset the switch seeFuel
Pump Shut-Off Switchlater in this chapter.
*
[ST08350(ALL)10/95]
A computer system controls the engine's idle
speed. When you start your vehicle, the engine's
idle speed normally runs high. These faster
engine speeds will make your vehicle coast
slightly faster than its normal idle speed. It
should, however, slow down after a short time.
If it does not, have the idle speed checked.
*
[ST08365(ALL)07/95]
If the engine idle speed does not slow down
automatically, do not allow your vehicle to idle
for more than 10 minutes. Have the vehicle
checked.
*
[ST08375(ALL)05/95]
RWARNING
Extended idling at high engine speeds can
produce very high temperatures in the
engine and exhaust system, creating the
risk of fire or other damage.
*
[ST08500(ALL)05/95]
RWARNING
Do not park, idle, or drive your vehicle in
dry grass or other dry ground cover. The
emission system heats up the engine
compartment and exhaust system, which
can start a fire.
File:04icstf.ex
Update:Wed Jan 24 14:30:41 1996
Page 55 of 268
53
*
[ST09510(ALL)10/95]
If your engine cranks but does not start after a
collision or major jolt:
*
[ST09520(ALL)02/95]
1. Turn the key in the ignition to the LOCK
position.
*
[ST09530(ALL)03/95]
2. Check under the vehicle for leaking fuel.
[ST09540(ALL)02/95]
3. If you do not see or smell fuel, remove the
door covering the fuel pump shut-off switch
compartment by pressing the tab toward the
rear seat. Push down the red reset button on
the fuel pump shut-off switch.
*
[ST09550(ALL)02/95]
4. Attempt to start your vehicle. If the vehicle
starts, let it run a few seconds, then turn the
key to the LOCK position.
*
[ST09560(ALL)03/95]
5. Check under the vehicle again for leaking
fuel.If you see or smell fuel, do not start
your vehicle again.If you do not see or
smell fuel, you can try to start your vehicle
again.
*
[ST09600(ALL)09/95]
RWARNING
Do not start your vehicle in a closed
garage or other enclosed area. Never sit in
a stopped vehicle for more than a short
period of time with the engine running.
Exhaust fumes are toxic. SeeGuarding
Against Exhaust Fumesin this chapter for
more instructions.
%*
[ST11700(ALL)05/95]
Guarding Against Exhaust Fumes
*
[ST11800(ALL)02/95]
Carbon monoxide, although colorless and
odorless, is present in exhaust fumes. Take
precautions to avoid its dangerous effects.
File:04icstf.ex
Update:Wed Jan 24 14:30:41 1996
Page 61 of 268
59
*
[LG02400(ALL)06/95]
Brake System Warning Light
[LG02550(ALL)09/93]
one inch art:0032206-B
Brake system and parking brake light
[LG02600(ALL)12/93]
This light comes on for a few seconds when you
turn the ignition key to START or ON. It
normally goes off shortly after the engine starts
and after you release the parking brake.
However, it may stay on for up to 60 seconds. If
the light doesn't illuminate after the engine is
started, stays on for longer than 60 seconds, or
comes on after you have fully released the
parking brake, have the hydraulic brake system
checked.
*
[LG02650(ALL)02/94]
This light will also come on if the parking brake
does not release fully. If it does stay onafterthe
parking brake is fully released, it means there
may be a brake problem. Pull off the road and
stop carefully. You may notice that the pedal is
harder to push, the pedal may go closer to the
floor, or it may take longer to stop the vehicle.
Try the brakes again after you have stopped.
[LG02675(ALL)02/95]
Your vehicle has a divided brake system. If one
part isn't working, the other part can still work
and stop the vehicle. For good braking, you
need both systems working well. If the warning
light goes on, there could be a problem. Have
the brake system inspected right away.
File:05iclgf.ex
Update:Wed Jan 24 14:32:51 1996