hood release FORD ASPIRE 1996 1.G Owners Manual
[x] Cancel search | Manufacturer: FORD, Model Year: 1996, Model line: ASPIRE, Model: FORD ASPIRE 1996 1.GPages: 268, PDF Size: 2.2 MB
Page 175 of 268
176
*
[SV02900(ALL)03/95]
Working with the engine on:
*
[SV03000(ALL)03/95]
1. Set the parking brake fully and make sure
the gearshift is securely latched in P (Park)
(automatic transaxle) or Neutral (manual
transaxle).
*
[SV03050(ALL)03/95]
2. Block the wheels. This will prevent your
vehicle from moving unexpectedly.
*
[SV03200(ALL)02/95]
RWARNING
Do not start your engine with the air
cleaner removed and do not remove it
while the engine is running.
*
[SV03400(ALL)03/95]
Opening the Hood
%*
[SV03500(ALL)01/95]
1. Inside the vehicle, pull the hood release
handle located under the bottom left corner
of the instrument panel.
%*
[SV03600(ALL)02/95]
2. Go to the front of the vehicle and release the
auxiliary latch that is located under the hood
at the center of the vehicle.
[SV03700(ALL)03/93]
3. Lift the hood and set the prop rod in the
hole in the hood.
*
[SV03800(ALL)11/90]
When you close the hood, make sure the prop
rod is in its retainer and that the hood latches
securely.
File:15icsvf.ex
Update:Wed Jan 24 14:56:41 1996
Page 176 of 268
177 [SV04200(ALL)07/93]
half page art:0032215-B
Hood release handle, hood latch and prop rod
[SV04500(ALL)05/93]
Your Engine Type
[SV05200(ALL)09/93]
Your vehicle has a 1.3L (81 CID), fuel injected,
overhead cam, four-cylinder engine.
[SV05300(ALL)02/92]
The following page shows you a diagram of the
engine and where to find items you should
regularly service.
File:15icsvf.ex
Update:Wed Jan 24 14:56:41 1996
Page 224 of 268
225
*
[SV40200(ALL)03/95]
Headlamp Bulb
*
[SV40400(ALL)01/95]
The headlamps on your vehicle use replaceable
bulbs. When the lamp burns out, simply replace
the bulb, rather than the whole lamp.
*
[SV40500(ALL)05/95]
RWARNING
Handle a halogen headlamp bulb carefully
and keep out of children's reach. Grasp
the bulb only by its plastic base and do
not touch the glass. The oil from your
hand could cause the bulb to break the
next time the headlamps are operated.
*
[SV40600(ALL)01/95]
Do not remove the burned-out bulb unless you
can immediately replace it with a new one. If a
bulb is removed for an extended period of time,
contaminants may enter the headlamp housing
and affect its performance.
*
[SV40700(ALL)03/95]
Removing the headlamp bulb
*
[SV40800(ALL)05/95]
1. Make sure that the headlamp knob is in the
OFF position.
*
[SV40900(ALL)02/95]
2. Lift the hood and find the bulb in the
headlamp socket.
[SV41000(ALL)05/93]
3. Remove the electrical connector from the
bulb housing by pushing the locking tabs on
either side and pulling out the connector.
[SV41100(ALL)05/93]
4. Remove the retaining ring by turning it 1/8
of a turn to free it from the socket. Then
slide the ring off.Keep the ring.You must
use it again to hold the new bulb in place.
[SV41125(ALL)05/93]
5. Remove the rubber boot. Save it because
you'll need it to cover the new bulb.
[SV41150(ALL)05/93]
6. Release the metal retaining clip that holds
the bulb in place.
File:15icsvf.ex
Update:Wed Jan 24 14:56:41 1996