spare wheel FORD ASPIRE 1996 1.G Owners Manual

142
*
[RE04000(ALL)03/95]
The Temporary Spare Tire
*
[RE04100(ALL)03/95]
You may have a high pressure temporary spare
tire. This spare tire is smaller than a regular tire
and is designed for emergency use only. Use it
only when you get a flat tire and replace it as
soon as you can. This spare tire is marked with
the words ªTEMPORARY USE ONLYº so that
you can easily identify it.
*
[RE04200(ALL)01/93]
RWARNING
If you use the temporary spare tire
continuously or do not follow these
precautions, the tire could fail, causing
you to lose control of the vehicle, possibly
injuring yourself or others.
*
[RE04300(ALL)01/95]
When you drive with the temporary spare tire,
DO NOT:
*
[RE04400(ALL)01/95]
q
exceed 50 mph (80 km/h) under any
circumstances.
*
[RE04500(ALL)01/95]
q
load your vehicle so that it is heavier than
the maximum vehicle load rating listed on
the tire decal.
*
[RE04700(ALL)01/95]
q
use tire chains on this tire.
*
[RE04800(ALL)01/95]
q
try to repair the temporary spare tire or
remove it from its wheel.
*
[RE04900(ALL)01/95]
q
use the wheel for any other type of vehicle.
*
[RE05000(ALL)01/95]
q
drive through an automatic car wash with
this tire. Because the temporary spare tire is
smaller than a conventional tire, it reduces
the ground clearance. Your vehicle may get
caught in the rails and it could be damaged.
File:12icref.ex
Update:Wed Jan 24 14:52:09 1996

145
*
[RE08100(ALL)05/95]
RWARNING
If the vehicle slips off the jack, you or
someone else could be seriously injured.
[RE08250(ALL)02/95]
2. Get out the spare tire and jack.
[RE08275(ALL)07/93]
To remove the tire, turn the hold-down bolt
counterclockwise with the wheel lug wrench.
To remove the jack, turn the jack hold-down
bolt counterclockwise. Remove the tire
retaining tool from the tool kit.
[RE08350(ALL)05/93]
3. Remove the wheelcover with the tapered
end of a wheel nut wrench. Insert the handle
of the wrench and twist it against the inner
wheelcover flange. Remove any chrome nuts
or plastic caps covering the wheel lug bolts.
[RE08400(ALL)07/93]
4. Remove the top lug bolt and insert the tire
retaining tool in its place. This will hold the
tire in place when the other lug bolts are
removed.
File:12icref.ex
Update:Wed Jan 24 14:52:09 1996

147 [RE08650(ALL)02/95]
Removing and Replacing the Tire
[RE08700(ALL)02/95]
1. Find the jack location near the door of the
tire that you are changing. Position the jack
and turn the handle of the jack clockwise
until the wheel is completely off the ground.
*
[RE08800(ALL)05/95]
RWARNING
To lessen the risk of personal injury, do
not put any part of your body under the
vehicle while changing a tire. Do not start
the engine when your vehicle is on the
jack. The jack is only meant for changing
the tire.
[RE09200(ALL)05/93]
one third page art:0032213-A
Jack mounting position
[RE09600(ALL)02/95]
2. Remove the wheel bolts by using the lug
wrench. Never loosen the hub nuts. See the
illustration following Step 1Preparing to
Change the Tireif you are not sure where to
find the wheel bolts.
[RE09700(ALL)02/95]
3. Replace the flat tire with the spare tire. Keep
the retaining tool in place.
File:12icref.ex
Update:Wed Jan 24 14:52:09 1996

148 [RE09750(ALL)09/93]
half page art:0032248-BPositioning spare tire
[RE09900(ALL)02/95]
4. Replace the wheel lug bolts, but do not fully
tighten them until you lower the car. If you
do, you could force the car off the jack.
[RE10000(ALL)02/95]
5. Remove the retaining tool and replace it
with the final lug bolt.
[RE10090(ALL)07/95]
Your vehicle is built with metric (12 mm)
threads on the wheel hubs and lug bolts. Make
certain, during wheel removal, the same bolts
removed are reinstalled, or if replaced, bolts
with metric threads and the same chamfer
configuration are used.
[RE10100(ALL)07/95]
RWARNING
Installation of an English thread lug bolt
into a metric hub will not properly secure
the wheel to the hub. Damaged lug bolts
may result in wheel separation and
possible injury.
File:12icref.ex
Update:Wed Jan 24 14:52:09 1996

149 [RE10200(ALL)03/95]
6. Lower the vehicle by turning the jack handle
counterclockwise.
[RE10500(ALL)02/95]
7. Remove the jack and fully tighten the wheel
lug bolts in the order shown in the
illustration under Step 1.
[RE10700(ALL)02/95]
8. Put the tire, jack, retaining tool and wrench
away.
[RE10750(ALL)02/95]
9. Secure the conventional tire where the spare
was stored with the bolt provided.
[RE10850(ALL)02/95]
10. Unblock the wheels.
*
[RE12150(ALL)12/91]
If the Engine Cranks but Does
Not Start or Starting After a
Collision
*
[RE12225(ALL)07/95]
If the engine cranks but does not start or if you
have had a collision, the fuel pump shut-off
switch may have been triggered. The shut-off
switch is a device that stops the fuel pump
when your vehicle has been involved in a
substantial jolt.
*
[RE12250(ALL)07/95]
For information on how to check and reset the
fuel pump shut-off switch, seeFuel pump shut-off
switchin the Index.
*
[RE12300(ALL)05/95]
Towing Your Vehicle
[RE12500(ALL)07/95]
If you need to have your vehicle towed, contact
a professional towing service or, if you are a
member, your roadside assistance center.
Suggested towing options include wheel lift
towing or flat bed towing.
File:12icref.ex
Update:Wed Jan 24 14:52:09 1996

203
*
[SV27000(ALL)01/95]
RWARNING
When replacing full size tires, never mix
radial, bias-belted, or bias-type tires. Use
only the tire sizes that are listed on the
tire pressure decal. Make sure that all tires
are the same size, speed rating, and
load-carrying capacity. Use only the tire
combinations recommended on the decal.
If you do not follow these precautions,
your vehicle may not drive properly and
safely.
*
[SV27100(ALL)01/95]
Tires that are larger or smaller than your
vehicle's original tires may also affect the
accuracy of your speedometer.
*
[SV27200(ALL)04/95]
Wheel and Tire Matching
[SV27250(ALL)02/95]
See an authorized tire dealer for proper
servicing procedures. Wheels and tires must be
properly removed, matched and remounted to
maintain the best possible ride.
%*
[SV28100(ALL)02/95]
Information About Tire Quality Grades
*
[SV28200(ALL)01/95]
New vehicles are fitted with tires that have their
Tire Quality Grade (described below) molded
into the tire's sidewall. These Tire Quality
Grades are determined by standards that the
United States Department of Transportation has
set.
*
[SV28250(ALL)01/95]
Tire Quality Grades apply to new pneumatic
tires for use on passenger cars. They do not
apply to deep tread, winter-type snow tires,
space-saver or temporary use spare tires, tires
with nominal rim diameters of 10 to 12 inches or
limited production tires as defined in Title 49
Code of Federal Regulations Part 575.104(c)(2).
File:15icsvf.ex
Update:Wed Jan 24 14:56:41 1996

206 [SV29220(ALL)07/93]Use chains on the tires only in an emergency or
if the law requires them where you live. If you
choose to use chains on your vehicle's tires, be
aware of the following:
*
[SV29250(ALL)11/94]
q
Local regulations may prohibit or restrict the
use of tire chains. Investigate the laws and
regulations in your area before installing
chains.
*
[SV29320(ALL)07/94]
q
Tire chains may scratch or chip aluminum
wheels. IT IS RECOMMENDED THAT TIRE
CHAINS ARE INSTALLED ON STEEL
WHEELS ONLY. Be sure to remove wheel
covers (if equipped) from steel rims before
using tire chains to avoid scratches or
damage.
*
[SV29350(ALL)05/95]
q
Put the chains on the front tires tightly with
the ends held down securely. Retighten the
chains after driving 1/2 mile (1 km). Follow
the chain manufacturer's instructions.
[SV29420(ALL)07/94]
q
Do not drive faster than 30 mph (48 km/h)
or the chain manufacturer's recommended
speed limit, whichever is lower. Avoid
bumps, holes and sharp turns. If you can
hear the chains rub or bang against your
vehicle, remove the chains to prevent damage
to your vehicle.
*
[SV29450(ALL)07/94]
q
Tire chains may affect vehicle handling. Drive
carefully and avoid hard braking.
[SV29520(ALL)07/94]
q
Do not use chains on temporary spare tires.
They may damage the vehicle and the tire.
File:15icsvf.ex
Update:Wed Jan 24 14:56:41 1996