wiper blades FORD ASPIRE 1996 1.G Owners Manual

87 [SC04500(ALL)05/93]
quarter page art:0032178-A
Windshield washer control
[SC04600(ALL)07/93]
If the washer does not work, check the washer
fluid level and fill it if it is low. SeeServicing
Your Aspirelater in the owner guide. If there is
fluid in the reservoir, consult your nearest
authorized Ford dealer.
*
[SC04700(ALL)01/95]
Do not try to clean the windshield when the
washer fluid container is empty or activate the
washers at any time for more than 15 seconds
continuously. This could damage the washer
pump system.
*
[SC04800(ALL)01/93]
RWARNING
In freezing weather, the washer solution
may freeze on the windshield and obscure
your vision. Always warm up the
windshield with the defroster before you
use the washer fluid. If you cannot see
through the windshield clearly, it can
increase the risk of being involved in a
collision.
*
[SC04900(ALL)04/95]
For information about refilling the washer fluid
or replacing your windshield wiper blades, see
Windshield washer fluid and Wipersin the Index.
File:07icscf.ex
Update:Wed Jan 24 14:50:00 1996

197
(VOC's) may restrict use of the most common
antifreeze, methanol. Washer fluids containing
non-methanol antifreeze agents should be used
only if they provide cold weather protection
without damaging the vehicle's paint finish,
wiper blades, and windshield washer system.
[SV23200(ALL)04/95]
Rear window wiper (If equipped)
[SV23300(ALL)07/93]
Your Aspire may have a rear wiper/washer
system. The washer fluid reservoir is located in
the right side of the luggage compartment. To
open the reservoir compartment cover, pull out
the knob and pull the door open.
[SV23400(ALL)07/93]
two third page art:0032212-A
Rear washer fluid reservoir
File:15icsvf.ex
Update:Wed Jan 24 14:56:41 1996

198 [SV23900(ALL)02/95]This is not the same reservoir your front
windshield wipers use. Refill this reservoir with
the same solution you use for your windshield.
*
[SV24000(ALL)03/95]
Wiper Blades
*
[SV24100(ALL)03/95]
Check the windshield wiper blades at least twice
a year. Also check them whenever they seem
less effective than usual. Substances such as tree
sap and some hot wax treatments used by
commercial car washes reduce the effectiveness
of wiper blades.
*
[SV24200(ALL)03/95]
If the blades do not wipe properly, clean both
the windshield and the wiper blades. Use
undiluted windshield washer solution or a mild
detergent. Rinse thoroughly with clear water. Do
not use fuel, kerosene, paint thinner, or other
solvents to clean your wiper blades. These will
damage your blades.
*
[SV24300(ALL)03/95]
To make reaching the wiper blades easy, simply
turn the ignition to the ACC position and turn
your wipers on. Wait for them to reach a
vertical position and turn the ignition to the OFF
position. Do not move the wipers manually.
Manually moving the wipers across the
windshield may damage them.
*
[SV24400(ALL)03/01]
Wiper blade replacement
*
[SV24500(ALL)01/95]
If the wipers still do not work properly after
you clean them, you may need to replace the
wiper blade assembly. When replacing the wiper
blade assembly always use a Motorcraft part or
equivalent.
*
[SV24525(ALL)10/93]
To replace the wiper blades:
*
[SV24535(ALL)06/95]
1. Pull the wiper arm away from the
windshield and into the lock position.
*
[SV24550(ALL)03/94]
2. Turn the blade at an angle from the wiper
arm. Push the lock pin with a screwdriver to
release the blade and pull the wiper blade
down toward the windshield to remove it
from the arm.
File:15icsvf.ex
Update:Wed Jan 24 14:56:41 1996

199
*
[SV24560(ALL)03/94]
3. Attach a new wiper blade to the wiper arm
and press it into place until you hear it click.
[SV24575(ALL)03/94]
two third page art:0032257-A
Replacing the wiper blades
File:15icsvf.ex
Update:Wed Jan 24 14:56:41 1996