ECU FORD ASPIRE 1997 1.G Owner's Manual

147
*
[MC02000(ALL)01/96]
q
Do not work on a vehicle in an enclosed
space with the engine running, unless you are
sure you have enough ventilation.
*
[MC02100(ALL)01/96]
q
Never get under a vehicle while it is
supported only by a jack. If you must work
under a vehicle, use safety stands.
*
[MC02200(ALL)01/96]
q
Keep all lit cigarettes and other smoking
materials away from the battery and all
fuel-related parts.
*
[MC02700(ALL)01/96]
Working with the engine off:
[MC02750(ALL)01/96]
1. Set the parking brake fully and make sure
the gearshift is securely latched in P (Park)
(automatic transaxle) or 1 (First) gear
(manual transaxle).
*
[MC02800(ALL)01/96]
2. Remove the key from the ignition after you
turn the engine off.
*
[MC02850(ALL)01/96]
3. Block the wheels. This will prevent your
vehicle from moving unexpectedly.
*
[MC02900(ALL)01/96]
Working with the engine on:
*
[MC03000(ALL)01/96]
1. Set the parking brake fully and make sure
the gearshift is securely latched in P (Park)
(automatic transaxle) or Neutral (manual
transaxle).
*
[MC03050(ALL)01/96]
2. Block the wheels. This will prevent your
vehicle from moving unexpectedly.
*
[MC03200(ALL)01/96]
WARNING
Do not start your engine with the air
cleaner removed and do not remove it
while the engine is running.
File:11icmcf.ex
Update:Tue Mar 4 08:57:16 1997

148 %
*
[MC04000(ALL)02/96]
Opening the Hood
%*
[MC04100(ALL)02/96]
1. Inside the vehicle, pull the hood release
handle located under the bottom left corner
of the instrument panel.
%*
[MC04200(ALL)02/96]
2. Go to the front of the vehicle and release the
auxiliary latch that is located under the hood
at the center of the vehicle.
[MC04300(ALL)02/96]
3. Lift the hood and set the prop rod in the
hole in the hood.
*
[MC04400(ALL)02/96]
When you close the hood, make sure the prop
rod is in its retainer and that the hood latches
securely.
[MC04500(ALL)04/96]
half page art:0032215-C
Hood release handle, hood latch and prop rod
File:11icmcf.ex
Update:Tue Mar 4 08:57:16 1997

150
*
[MC05650(ALL)05/96]
NOTE: Ford production and aftermarket
(Motorcraft) oil filters are designed for
added engine protection and long life.
If a replacement oil filter is used that
does not meet Ford material and design
specifications, startup engine noises or
knock may be experienced. It is
recommended you use the appropriate
ªMotorcraftº oil filter (or another brand
meeting Ford specifications) for your
engine application.
%*
[MC05700(ALL)01/96]
Checking and Adding Engine Oil
*
[MC05800(ALL)01/96]
Since the proper amount of engine oil is
important for safe engine operation, check the oil
using the dipstick each time you put fuel in
your vehicle. Remember the engine must be off,
the oil must be warm and the vehicle must be
parked on level ground.
%*
[MC05900(ALL)01/96]
Checking the engine oil level:
*
[MC06000(ALL)01/96]
1. Turn the engine off after it has warmed up
and allow a few minutes for the engine oil
to drain back into the oil pan.
[MC06100(ALL)01/96]
2. Set the parking brake fully and make sure
the gearshift is securely latched in P (Park)
or 1 (First).
*
[MC06200(ALL)01/96]
3. Open the hood. Protect yourself from engine
heat.
[MC06300(ALL)01/96]
4. Locate the dipstick (highlighted in yellow)
and carefully pull it out of the engine.
*
[MC06400(ALL)01/96]
5. Wipe the dipstick clean and put it back into
position, making sure it is fully seated.
File:11icmcf.ex
Update:Tue Mar 4 08:57:16 1997

161
%*
[MC29542(ALL)01/96]
Automatic Transaxle Fluid
*
[MC29544(ALL)02/96]
Under normal circumstances, you do not need to
check the fluid level of the transaxle, since your
vehicle does not use up transaxle fluid. Refer to
theMaintenance Schedulebooklet for replacement
intervals. However, if the transaxle is not
working properly Ð for instance, the transaxle
may slip or shift slowly, or you may notice
some sign of fluid leakage Ð the fluid level
should be checked.
%*
[MC29546(ALL)01/96]
Checking the Automatic Transaxle Fluid
[MC29548(ALL)04/96]
With the vehicle on a level surface and the brake
pedal fully applied, start the engine and move
the gearshift selector through all of the gears.
Allow sufficient time for each position to engage.
Securely latch the gearshift selector in the P
(Park) position. Fully set the parking brake and
leave the engine running.
[MC29550(ALL)01/96]
Pull the dipstick out and wipe the indicator end
clean. Put the dipstick back into the filler tube
and make sure it is fully seated; otherwise, you
will not get an accurate reading. Pull the
dipstick out and read the fluid level.
[MC29555(ALL)01/96]
one third page art:0032228-B
Automatic transaxle fluid dipstick
File:11icmcf.ex
Update:Tue Mar 4 08:57:16 1997

174
*
[MC43260(ALL)01/96]
q
Put the chains on the front tires tightly with
the ends held down securely. Retighten the
chains after driving 1/2 mile (1 km). Follow
the chain manufacturer's instructions.
*
[MC43262(ALL)01/96]
q
Do not drive faster than 30 mph (48 km/h)
or the chain manufacturer's recommended
speed limit, whichever is lower. Avoid
bumps, holes and sharp turns. If you can
hear the chains rub or bang against your
vehicle, remove the chains to prevent damage
to your vehicle.
*
[MC43264(ALL)01/96]
q
Tire chains may affect vehicle handling. Drive
carefully and avoid hard braking.
*
[MC43266(ALL)01/96]
q
Do not use chains on temporary spare tires.
They may damage the vehicle and the tire.
%
*
[MC43755(ALL)01/96]
Filling the Fuel Tank
[MC43760(ALL)01/96]
Your fuel hatch door is located on the driver's
side. To open the fuel door, simply pull the
hatch open.
[MC43765(ALL)01/96]
one third page art:0032224-B
Fuel hatch and fuel cap
*
[MC43770(ALL)01/96]
If you lose the fuel cap, replace it with an
authorized Motorcraft or equivalent part.
File:11icmcf.ex
Update:Tue Mar 4 08:57:16 1997

188
*
[MC62900(ALL)01/97]
Installing the headlamp bulb
[MC62950(ALL)01/96]
1. Insert the glass end of the bulb assembly
into the socket.
[MC63000(ALL)01/96]
2. Secure the bulb assembly in place with the
metal retaining clip.
[MC63100(ALL)01/96]
3. Attach the rubber boot over the bulb
assembly.
[MC63200(ALL)01/96]
4. Slip the bulb retaining ring over the boot
and bulb assembly. Lock the ring into the
socket by rotating it clockwise until you feel
a ªstopº.
[MC63300(ALL)01/96]
5. Push the electrical connector into the rear of
the bulb assembly until it locks into position.
[MC63400(ALL)01/96]
6. Turn the headlamps on and make sure they
work properly. If the headlamp was
correctly aligned before you changed the
bulb, you should not need to align it again.
File:11icmcf.ex
Update:Tue Mar 4 08:57:16 1997