lamps FORD C MAX 2008 1.G User Guide

Downloaded from www.Manualslib.com manuals search engine A message will appear in theinformation display and the headlampindicator flashes if the systemmalfunctions. See Informationmessages (page 103). Theheadlamps will move to a fixedcentral or dipped position. Have thesystem checked as soon as possible.
69
Lighting

Downloaded from www.Manualslib.com manuals search engine INTERIOR LAMPS
Courtesy lamp
OffA
Door contactB
OnC
If you set the switch to position B, thecourtesy lamp will come on when youunlock or open a door or the luggagecompartment lid. If you leave a dooropen with the ignition switch off, thecourtesy lamp will go offautomatically after some time toprevent the vehicle battery fromdischarging. To switch it back on,switch on the ignition for a short time.
The courtesy lamp will also come onwhen you switch off the ignition. It willgo off automatically after a short timeor when you start or restart theengine.
If you set the switch to position Cwith the ignition switch off, thecourtesy lamp will come on. It will gooff automatically after a short time toprevent the vehicle battery fromdischarging. To switch it back on,switch on the ignition for a short time.
Reading lamps
If you switch off the ignition, thereading lamps will go off automaticallyafter some time to prevent thevehicle battery from discharging. Toswitch them back on, switch on theignition for a short time.
Vanity mirror lamps
OffA
OnB
72
LightingCBAE71945 E71946 ABE72900

Downloaded from www.Manualslib.com manuals search engine If you switch off the ignition, the vanitymirror lamps will go off automaticallyafter a short time to prevent thevehicle battery from discharging. Toswitch them back on, switch on theignition for a short time.
73
Lighting

Downloaded from www.Manualslib.com manuals search engine CHANGING A BULB
WARNINGS
On vehicles fitted with Xenonheadlamps, have the headlampbulbs changed by an expert. Thereis a risk of injury due to high voltage.
During operation, the bulbs andtheir surroundings get hot.Switch off the lights and let the bulbscool down before replacing them.
Always switch off lights and ignitionbefore replacing any bulb.
Never touch the glass of the bulbs.Fit only bulbs having a UV filter.Always replace a faulty bulb with anew one of the same type. Afterreplacing a bulb, check that the lightsoperate correctly.
Headlamps, side lamps,direction indicators
Note:It is necessary to remove theheadlamp assembly to remove anyof the bulbs.
Removing the headlampassembly
Open the bonnet.
Remove the screw.
WARNING
When re-installing the lampassembly, make sure that thewiring connectors and retaining clipsare engaged properly.
Press down the retaining clips at therear of the lamp assembly using ascrewdriver and carefully pull out thelamp assembly.
74
LightingE78106 E78107

Downloaded from www.Manualslib.com manuals search engine Disconnect the wiring connector.
Install in the reverse order.
Front direction indicators
PY21 watt spherical bulb, orange
•Turn the bulb holder anticlockwiseand pull out.
•Turn the bulb under slightpressure anticlockwise andremove it.
•Replace the bulb.
When installing, pay attention to theguide tabs.
Opening the headlampassembly (Type 1)
Note:When replacing the cover,ensure that no wires are trapped atthe seals and that the clips engagewith a distinct click.
Release the clips and remove thecover.
Opening the headlampassembly (Type 2)
Remove the rubber caps.
Headlamps – dipped beam(Type 1)
H7, 55 watt halogen bulb
75
LightingE78108 E78109 E91732

Downloaded from www.Manualslib.com manuals search engine •Disconnect the wiring connector.
•Release the wire clip, swivel it tothe side and pull out the bulb.
Install in the reverse order.
Headlamps – dipped beam(Type 2)
H7, 55 watt halogen bulb
•Turn the bulb holder anticlockwiseand pull it out.
•Pull out the bulb and replace it.
Install in the reverse order.
Headlamps – main beam
H1, 55 watt halogen bulb
•Disconnect the wiring connector.
•Release the wire clip, swivel itdown and pull out the bulb.
Install in the reverse order.
Side lamps
5 watt wedge base bulb
76
LightingE78110 E91734 E78111

Downloaded from www.Manualslib.com manuals search engine Remove the bulb holder from theassembly. Remove and replace thebulb.
Install in the reverse order. Whenreinstalling the scull cap, first insert itat the top and then press it down atthe bottom until it clicks into place.
Approach lamps
5 watt wedge base bulb
Carefully prise out the lamp assemblyat the outer edge and pull it out.
Turn the lamp housing anticlockwiseand remove it. Pull the bulb out.
Install in the reverse order.
Front fog lamps (Type 1)
H8, 35 watt halogen bulb
78
LightingE78116 E78117 E78118 E78119

Downloaded from www.Manualslib.com manuals search engine •Prise out the fog lamp bezel at itsbase, slide the bezel downwardsand remove it.
•Loosen the screws and pull outthe lamp assembly.
•Disconnect the wiring connector.
•Remove the bulb and replace it.
Install in the reverse order.
Vehicles with a body styling kit
Insert your fingers into the hole in thebezel above the fog lamp and pull offthe complete bezel.
Front fog lamps (Type 2)
H8, 35 watt halogen bulb
1.Prise out the fog lamp bezel at itsbase, slide the bezel downwardsand remove it.
2.Loosen the screws and pull outthe lamp assembly.
3.Disconnect the wiring connector.
4.Remove the bulb and replace it.
79
LightingE78120 E78121 12E91735 34E91736

Downloaded from www.Manualslib.com manuals search engine Install in the reverse order.
Rear lamps
Open the tailgate.
Remove the pillar panel trim insidethe luggage compartment.
Remove the sidewall panel trim togain access to the second wing nut.
Remove the wingnuts. Make sure thewing nuts do not fall into the opening.
Pull off the rear lamp assembly outof the two plastic retainers on thebody panel.
Disconnect the wiring connector.
Loosen the screws and remove thecomplete bulb holder.
80
LightingE78122 E78123 E78124 E78125

Downloaded from www.Manualslib.com manuals search engine Brake lamp P21 wattA
Direction indicator PY21 watt(orange)B
Reversing lamp P21 wattC
Rear fog lamp/tail lampP21/4 WattD
Note:Vehicles may not have a taillamp if an LED board is fitted. TheLED board is not a serviceable item,please consult your dealer if this fails.
Turn the bulb anticlockwise underslight pressure and remove it.Replace the bulb.
Install in the reverse order. Afterinstallation, check that the lightsoperate correctly.
Central brake lamp
Consult an expert.
Number plate lamp
5 watt festoon
Loosen the two screws, and removethe lamp assembly.
Install in the reverse order.
Interior and reading lamps
Switch off the lights.
Insert a flat-bladed screwdriver intothe recess between the body of theunit and the lens at the opposite sideto the switches. Gently prise out thelens a short way. Take hold of theside of the lens and lift it off the unit.
81
LightingE78126 E72556 E7812812