engine FORD CONTOUR 1996 2.G Service Manual

Roadside Emergencies
167
*
[RE03400(ALL)03/95]
Jump-Starting
*
[RE03600(ALL)03/95]1.
Make sure that the jumper cables are not in the way of
moving engine parts, then start the booster vehicle. Run the
engine at a moderate speed.
*
[RE03700(ALL)03/95]2.
Let the discharged battery charge for a few minutes and then
start the disabled vehicle. It may take a couple of tries before
the vehicle starts. If the vehicle does not start after several
attempts, there may be a different problem.
*
[RE03800(ALL)03/95]3.
When both vehicles are running, let them idle for a few
minutes to charge the discharged battery.
*
[RE03900(ALL)03/95]
Removing jumper cables
*
[RE04000(ALL)03/95]1.
Always remove the jumper cables in the reverse order.
Remove the negative (±) end of the jumper cable from the
metallic surface on the engine or frame of the disabled
vehicle.
*
[RE04100(ALL)05/95]2.
Remove the negative (±) cable from the booster battery.
*
[RE04200(ALL)03/95]3.
Remove the positive (+) cable from the booster battery.
*
[RE04300(ALL)05/95]4.
Remove the other end of the positive (+) cable from the
discharged battery.
*
[RE04400(ALL)04/95]
After the vehicle is started, let it idle for a while to let the
engine ªrelearnº its idle conditions. Drive it around for a while
with all electrical accessories turned off to let the battery
recharge.You may need to use a battery charger to fully
recharge the battery.
*
[RE04450(ALL)03/95]
If you need to replace your battery, seeBatteryin theServicing
Your Vehiclechapter.
File:cdreo.ex
Update:Thu Jan 25 12:24:30 1996

170
*
[RE07400(ALL)03/95]
Preparing to Change the Tire
[RE07650(ALL)05/94]1.
Make sure that your vehicle will not move or roll. If you
have an automatic transaxle, put the gearshift in P (Park). If
you have a manual transaxle, put the gearshift in 1 (First).
Set the parking brake and block the wheel that is diagonally
opposite the tire that you are changing.
[RE08500(ALL)05/95]
When one of the front wheels is off the ground, the transaxle
alone will not prevent the vehicle from moving or slipping off
the jack, even if the vehicle is in P (automatic) or 1 (manual). To
prevent the vehicle from moving when you change one of the
front tires, put a block behind the wheel that is diagonally
opposite to the tire.
*
[RE08600(ALL)05/95]
RWARNING
If the vehicle slips off the jack, you or someone else
could be seriously injured.
*
[RE08800(ALL)05/95]2.
Get out the spare tire and jack.
*
[RE08825(ALL)05/95]
RWARNING
To avoid injury, never run the engine with one wheel off
the ground, such as when changing a tire.
[RE08850(ALL)01/95]3.
Remove the wheel cover from the wheel with the tapered
end of the wheel lug wrench. Insert and twist the handle,
then pry against the inner wheel cover flange. For
information about removing optional wheel center ornaments
seeStyled Polycast Wheel Ornamentslater in this section.
[RE09200(ALL)01/95]4.
Loosen the wheel lug nuts by pulling up on the handle of
the wrench one-half turn counterclockwise. Do not remove
the wheel lug nuts until you raise the tire off the ground.
For information about removing anti-theft lug nuts, see
Anti-Theft Wheel Lug Nutslater in this section.
File:cdreo.ex
Update:Thu Jan 25 12:24:30 1996

Roadside Emergencies
171
*
[RE09250(ALL)05/95]
Removing and Replacing the Tire
[RE09300(ALL)01/95]1.
Place the scissors-type jack under the side of the vehicle and
adjust the jack height with the jack handle. The jack should
fit in the notch in the vertical rocker panel flange which is
nearest to the wheel to be changed. The front and rear
jacking notches on each side of the vehicle are marked by
arrows in the rocker panel.
[RE09401(O )05/94]
On sport models with ªskirts,º you must remove a portion
of the skirt before placing the jack under the vehicle.
Squeeze the removeable portion of the skirt and pull down.
A tether connects it to the rocker panel.
[RE09500(O )05/94]
10-1/2 pica
art:0001300-A
Sports models with skirts
*
[RE09800(ALL)05/95]
RWARNING
To lessen the risk of personal injury, do not put any part
of your body under the vehicle while changing a tire. Do
not start the engine when your vehicle is on the jack.
The jack is only meant for changing the tire.
File:cdreo.ex
Update:Thu Jan 25 12:24:30 1996

Roadside Emergencies
175
*
[RE14800(ALL)03/95]
Replacing the anti-theft lug nut
*
[RE14900(ALL)03/95]
Insert the key over the locking lug nut. Place the lug nut
wrench over the lug nut key and, while applying pressure on
the key, install the lug nut.
*
[RE15050(ALL)02/95]
If the Engine Cranks But Does Not Start or
Does Not Start After a Collision
*
[RE15100(ALL)04/95]
The Fuel Pump Shut-off Switch
*
[RE15200(ALL)03/95]
If the engine cranks but does not start or if you have had a
collision, the fuel pump shut-off switch may have been
triggered. The shut-off switch is a device that stops the fuel
pump when your vehicle has been involved in a substantial jolt.
*
[RE15250(ALL)01/95]
For information on how to check and reset the fuel pump
shut-off switch, seeFuel pump shut-off switchin the Index.
*
[RE16400(ALL)05/95]
Towing Your Vehicle
*
[RE16500(ALL)04/95]
If you need to have your vehicle towed, contact a professional
towing service or, if you are a member, your roadside assistance
center. Recommended towing options include wheel lift towing
or flat bed towing.
File:cdreo.ex
Update:Thu Jan 25 12:24:30 1996

188
*
[HS08800(ALL)06/95]
Officials at the embassy or consulate can tell you where to get
unleaded fuel. If you cannot get unleaded fuel or can get only
fuel with an anti-knock index that is lower than your vehicle
needs, contact a district or owner relations office before you
leave the U.S. or Canada.
*
[HS08900(ALL)06/95]
Use of leaded fuel in your vehicle without a proper conversion
may damage the effectiveness of your emissions control system
and may cause engine knocking or serious engine damage. Ford
Motor Company is not responsible for any damage that is
caused by use of improper fuel.
*
[HS09000(ALL)06/95]
You may also have difficulty importing your vehicle back into
the U.S. if you use leaded fuel.
*
[HS09100(ALL)06/95]
If your vehicle must be serviced while you are traveling or
living in Central or South America, the Caribbean, or the
Middle East, contact the nearest Ford dealership. If the
dealership cannot help you, write to:
[HS09200(ALL)01/95]
7-1/2 pica art:0001307-C*
[HS09300(ALL)06/95]
If you are in other foreign countries, contact the nearest Ford
dealership. If the dealership cannot help you, they can direct
you to the appropriate Ford affiliate office.
*
[HS09400(ALL)06/95]
If you buy your vehicle in North America and then relocate
outside of the U.S. or Canada, register your Vehicle
Identification Number and new address with Ford Motor
Company Export Operations.
File:cdhso.ex
Update:Thu Jan 25 12:28:07 1996

189
Accessories
*
[AC00200(ALL)03/95]
Ford Accessories for Your Vehicle
*
[AC00225(ALL)04/95]
Ford has many fine products available from your dealer to clean
your vehicle and protect its finishes. For best results, use the
following, or products of equivalent quality:
*
[AC00250(ALL)05/95]
twelve pica
chart:0001433-A
*
[AC00300(ALL)04/95]
A wide selection of accessories is available through your local
authorized dealer. These fine accessories have been engineered
specifically to fulfill your automotive needs. They are custom
designed to complement the style and aerodynamic appearance
of your Ford-built vehicle. In addition, each accessory is made
from high quality materials and meets or exceeds Ford's rigid
engineering and safety specifications. That is why Ford brand
accessories are warranted for up to 3 years or 36,000 miles
(60,000 km), whichever comes first. See your dealer for complete
warranty information and accessory availability.
File:cdaco.ex
Update:Thu Jan 25 12:30:23 1996

Accessories
191
*
[AC00600(ALL)01/95]
NOTE: When adding accessories, equipment, passengers, and
luggage to your vehicle, do not exceed the total
weight capacity of the vehicle or of the front or rear
axle (GVWR, GAWR as shown on the Safety
Compliance Certification Label). Consult your dealer
for specific weight information.
*
[AC00700(ALL)05/95]
NOTE: The Federal Communications Commission (FCC) or
the Canadian Radio Telecommunications Commission
(CRTC) regulates the use of mobile communications
systems Ð such as two-way radios, telephones, and
theft alarms Ð that are equipped with radio
transmitters. Any such equipment installed in your
vehicle should comply with FCC or CRTC regulations
and should be installed only by a qualified technician.
*
[AC00800(ALL)01/95]
NOTE: Mobile communications systems may harm the
operation of your vehicle, particularly if they are not
properly designed for automotive use or are not
properly installed. For example, when operated, such
systems may cause the engine to stumble or stall. In
addition, such systems may themselves be damaged or
their operation affected by operating your vehicle.
(Citizens band [CB] transceivers, garage door openers,
and other transmitters whose power output is 5 watts
or less will not ordinarily affect your vehicle's
operation.)
*
[AC00900(ALL)05/95]
NOTE: Because we have no control over the installation,
design, or manufacture of such systems, Ford cannot
assume responsibility for any adverse effects or
damage that may result if you use this equipment.
File:cdaco.ex
Update:Thu Jan 25 12:30:23 1996

195
Servicing Your Contour
%*
[SV00300(ALL)03/95]
Service Made Easy
*
[SV00400(ALL)01/95]
Ford has two goals for servicing your vehicle.
*
[SV00500(ALL)01/95]1.
When we can, we design parts that do not need to be
serviced.
*
[SV00600(ALL)01/95]2.
We want to make servicing your vehicle as easy as possible.
To help you:
*
[SV00700(ALL)01/95]
n
We highlight do-it-yourself items in yellow in the engine
compartment so that you can find them easily.
*
[SV00800(ALL)01/95]
n
When possible, we design parts Ð such as the headlamp
bulbs Ð that can be replaced without tools.
*
[SV00900(ALL)05/94]
n
We give you a Maintenance Schedule that makes tracking
routine service for your vehicle easy. The maintenance
schedule is located in theMaintenance Schedule and Record
booklet.
*
[SV01000(ALL)01/95]
This chapter tells you about the basic parts that you need to
check and service regularly.
*
[SV01150(ALL)02/95]
If your vehicle needs professional servicing, your dealership can
provide the parts and service required. Check yourWarranty
Information Bookletto find out which parts and services are
covered. Also see theCustomer Assistancechapter of this Owner
Guide.
*
[SV01250(ALL)03/95]
Ford Motor Company recommends that the Owner Maintenance
Checks listed in theMaintenance Schedule and Recordbooklet be
performed for the proper operation of your vehicle. In addition
to the conditions listed in theOwner Maintenance Checklist,be
alert for any unusual noise, vibration, or other indication that
your vehicle may need service. If you do notice something
unusual, see that your vehicle is serviced promptly.
File:cdsvo.ex
Update:Thu Jan 25 12:09:28 1996

196
*
[SV01275(ALL)03/95]
Use only recommended fuels, lubricants, fluids, and service
parts conforming to Ford specifications. Motorcraft parts are
designed and built to provide the best performance in your
vehicle. Using these parts for replacement is your assurance that
Ford-built quality stays in your vehicle.
%*
[SV01280(ALL)04/95]
NOTE: Always dispose of used automotive fluids in a
responsible manner. Follow your community's
standards for disposing of these types of fluids. Call
your local recycling center to find out about recycling
automotive fluids.
*
[SV01600(ALL)03/95]
Precautions When Servicing Your Vehicle
*
[SV01700(ALL)01/95]
Be especially careful when inspecting or servicing your vehicle.
Here are some general precautions for your safety:
%*
[SV01800(ALL)03/95]
n
Do not work on a hot engine. The engine cooling fan may
come on unexpectedly. Always turn the engine off and let it
cool.
*
[SV01850(ALL)05/95]
RWARNING
The cooling fan is automatic and may come on at any
time. Always disconnect the negative terminal of the
battery before working near the fan.
*
[SV01900(ALL)03/95]
n
If you must work with the engine running, avoid wearing
loose clothing or jewelry that could get caught in moving
parts. Take appropriate precautions with long hair.
*
[SV02000(ALL)01/95]
n
Do not work on a vehicle in an enclosed space with the
engine running, unless you are sure you have enough
ventilation.
*
[SV02100(ALL)01/95]
n
Never get under a vehicle while it is supported by a jack
only. If you must work under a vehicle, use safety stands.
File:cdsvo.ex
Update:Thu Jan 25 12:09:28 1996

Servicing Your Contour
197
*
[SV02200(ALL)01/95]
n
Keep all lit cigarettes and other smoking materials away
from the battery and all fuel-related parts.
*
[SV02575(ALL)03/95]
Working with the engine off:
[SV02625(ALL)02/95]1.
Set the parking brake fully and make sure that the gearshift
is securely latched in P (Park) (automatic transaxle) or
1 (First) gear (manual transaxle).
*
[SV02650(ALL)03/95]2.
Remove the key from the ignition after you turn the engine
off.
*
[SV02675(ALL)03/95]3.
Block the wheels. This will prevent your vehicle from
moving unexpectedly.
*
[SV02700(ALL)03/95]
Working with the engine on:
*
[SV02825(ALL)04/95]1.
Set the parking brake fully and make sure the gearshift is
securely latched in P (Park) (automatic transaxle) or
Neutral (manual transaxle).
*
[SV02850(ALL)03/95]2.
Block the wheels. This will prevent your vehicle from
moving unexpectedly.
*
[SV03000(ALL)02/95]
RWARNING
Do not start your engine with the air cleaner removed
and do not remove it while the engine is running.
*
[SV03050(ALL)03/95]
If the battery is disconnected, the computer must relearn its idle
control. SeeBatteryin the Index.
File:cdsvo.ex
Update:Thu Jan 25 12:09:28 1996