ECU FORD CONTOUR 1997 2.G User Guide

Seating and Safety Restraints
111
*
[SS16800(ALL)02/96]6.
Before placing the child in the child seat, forcibly tilt the seat
from side to side, and tug it forward to make sure that the
seat is securely held in place. See Figure 7.
[SS16900(ALL)12/95]
17-1/2 pica
art:0001276-BFile:06cdsso.ex
Update:Thu Sep 12 11:03:20 1996

112
*
[SS17000(ALL)02/96]7.
Double check that the retractor is in the automatic locking
mode. Try to pull more belt out of the retractor. If you
cannot, the belt is in the automatic locking mode. See
Figure 8.
[SS17100(ALL)12/95]
17-1/2 pica
art:0001277-B[SS17200(ALL)12/95]8.
Check to make sure that the child seat is properly secured
prior to each use. If the belt is not locked, repeat steps 4
through 7.
[SS17300(ALL)12/95]
To remove retractor from automatic lock mode, unbuckle the
belt and allow the webbing to retract fully. A click will be
heard as the belt retracts. The belt is back in normal operating
mode (vehicle sensitive emergency locking mode) when this
click disappears.
File:06cdsso.ex
Update:Thu Sep 12 11:03:20 1996

Seating and Safety Restraints
113
*
[SS17400(ALL)03/96]
RWARNING
Carefully follow all of the manufacturer's instructions
included with the safety seat you put in your vehicle. If
you do not install and use the safety seat properly, the
child may be injured in a sudden stop or collision.
[SS17500(ALL)12/95]
Installing Child Safety Seats in the Rear Center Seating
Position
[SS17600(ALL)04/96]
Some child safety seats may be too wide to fit in the rear center
seat. If you wish to install a child safety seat in the rear center
seating position, choose a child safety seat with a base that can
fit between the safety belt buckles. Otherwise, secure the child
safety seat in another seating position.
%*
[SS17700(ALL)04/96]
Attaching Safety Seats With Tether Straps
*
[SS17800(ALL)04/96]
Some manufacturers make safety seats that include a tether
strap that goes over the back of the vehicle seat and attaches to
an anchoring point. Other manufacturers offer the tether strap
as an accessory. Contact the manufacturer of your child safety
seat for information about ordering a tether strap.
[SS17900(ALL)12/95]
To install a tether from a child safety seat in the front seat,
route the tether strap under the vehicle seat head restraint and
hook the tether hook into the hole in the tongue of the center
rear lap belt. After the hook is in the hole, pull on the loose end
of the lap belt webbing to shorten the belt and tighten the
tether strap.
[SS18000(ALL)12/95]
To install a tethered child safety seat in the rear seat, you will
need tether anchorage hardware.
File:06cdsso.ex
Update:Thu Sep 12 11:03:20 1996

128
%*
[GF02300(ALL)01/96]
Parking Brake
*
[GF02400(ALL)03/96]
The parking brake should be used whenever you park your
vehicle.
*
[GF02500(ALL)01/96]
The parking brake lever is located between the front seats. To
set the parking brake, put your foot on the brake pedal while
pulling the parking brake handle fully and firmly upward.
*
[GF02600(ALL)01/96]
To release the parking brake, put your foot on the brake pedal,
pull the handle upward and push the button. Then lower the
handle to the released position while holding the button in.
*
[GF02700(ALL)01/96]
RWARNING
Always set the parking brake fully and make sure that
the gearshift is securely latched in P (Park) (automatic
transaxle) or in 1 (First) (manual transaxle).
*
[GF02800(ALL)01/96]
RWARNING
To prevent personal injury, do not release the parking
brake while outside the vehicle.
*
[GF02900(ALL)02/96]
RWARNING
If the parking brake is fully released, but the Brake
System light remains on, have the brakes checked
immediately. They may not be working properly.
*
[GF03000(ALL)03/96]
The parking brake is not designed to stop a moving vehicle, but
you can use the parking brake to stop your vehicle in an
emergency if the normal brakes fail. However, since the parking
brake applies only the rear brakes, the stopping distance will
increase greatly and the handling of your vehicle will be
adversely affected.
File:09cdgfo.ex
Update:Thu Sep 12 11:04:39 1996

132
[GF05800(ALL)12/95]
13-1/2 pica
art:0001264-C
Overriding the brake shift interlock
*
[GF05900(ALL)12/95]
The console-mounted gearshift will lock when you turn the key
to the LOCK position. When the gearshift is in any position
except P (Park), the ignition key cannot be turned to LOCK or
removed from the steering column. TO REMOVE THE KEY, the
gearshift levermustbe in P (Park).
*
[GF06000(ALL)01/96]
Once the gearshift is secure in the desired position, release the
brake pedal and use the accelerator as necessary.
File:09cdgfo.ex
Update:Thu Sep 12 11:04:39 1996

Driving
135
*
[GF07500(ALL)03/96]
When to use 2 (Second)
[GF07600(ALL)12/95]
When your vehicle is in 2 (Second), it automatically starts off in
second gear. Use 2 (Second) to help drive up moderately steep
hills or restart from a standstill on slippery roads. It prevents
the transaxle from frequently shifting up and down. It also
gives more engine braking than D (Drive) (with Transaxle
Control Switch activated) when going down hills.
[GF07700(ALL)12/95]
Do not go faster than 55 mph (90 km/h) in this gear. You can
upshift from 2 (Second) into D (Overdrive) at any speed.
*
[GF07800(ALL)01/96]
When to use 1 (First)
[GF07900(ALL)12/95]
This position limits the transaxle to first gear. It helps brake the
vehicle when going down hills where 2 (Second) is not
sufficient.
[GF08000(ALL)12/95]
Do not go faster than 38 mph (60 km/h) in this gear. You can
upshift from 1 (First) to 2 (Second) or from 1 (First) to D
(Overdrive) at any speed.
*
[GF08100(ALL)03/96]
P (Park)
*
[GF08200(ALL)01/96]
Always come to a complete stop before you shift into P (Park).
Make sure that the gearshift is securely latched in P (Park). This
locks the transaxle and prevents the front wheels from rotating.
*
[GF08300(ALL)03/96]
RWARNING
Always set the parking brake fully and make sure the
gearshift is latched in P (Park). Turn off the ignition
whenever you leave your vehicle.
*
[GF08400(ALL)01/96]
RWARNING
Never leave your vehicle unattended while it is running.
File:09cdgfo.ex
Update:Thu Sep 12 11:04:39 1996

136
[GF08500(ALL)12/95]
You can tell the gearshift is securely latched when the push
button has popped out. In this position the gear shift selector
lever cannot be moved unless the button is pushed in.
%*
[GF08600(ALL)01/96]
Driving with a Manual Transaxle
%*
[GF08700(ALL)01/96]
Using the Clutch
*
[GF08800(ALL)12/95]
In order to start the vehicle, the clutch pedal must be fully
depressed to the floor. Before starting the engine, make sure the
vehicle is in Neutral and the parking brake is set.
[GF08900(ALL)12/95]
After the engine starts, allow it to idle for a few seconds. Then,
hold your right foot on the brake pedal and release the parking
brake. With the clutch pedal depressed to the floor with your
left foot, move the gearshift into 1 (First) or R (Reverse).
[GF09000(ALL)12/95]
To move the vehicle, take your right foot off the brake pedal
and then slowly release the clutch pedal. (You may need to
press down slowly on the accelerator at the same time that you
release the clutch pedal.)
*
[GF09100(ALL)01/96]
Do not drive with your foot resting on the clutch pedal and do
not use the clutch to hold your vehicle at a standstill while
waiting on a hill. These actions will seriously reduce clutch life.
[GF09200(ALL)12/95]
Idling the Vehicle
[GF09300(ALL)12/95]
When the vehicle is stopped and the engine is running, DO
NOT rest your hand on or apply any pressure to gearshift lever
when the clutch pedal is not depressed. This may result in
erratic engine operation.
%*
[GF09400(ALL)01/96]
Shifting the Gears
*
[GF09500(ALL)01/96]
The gearshift for a manual transaxle is mounted on the floor.
The gearshift can be in one of seven possible positions, as
shown.
File:09cdgfo.ex
Update:Thu Sep 12 11:04:39 1996

Roadside Emergencies
167
*
[ER08600(ALL)03/96]6.
Remove the jack and fully tighten the lug nuts in the order
shown in the following illustration. As soon as possible, have
your dealer or a qualified service technician check the lug
nuts for proper torque specifications.
[ER08700(ALL)12/95]
13-1/2 pica
art:0000498-D
The lug nuts on the wheel
*
[ER08800(ALL)03/96]7.
Place any wheel covers and ornaments in the trunk.
*
[ER08900(ALL)03/96]8.
Put the tire, jack, and wrench away. Make sure the jack is
securely fastened so it does not rattle when you drive.
*
[ER09000(ALL)03/96]9.
Unblock the wheels.
[ER09100(ALL)12/95]
Removing and Replacing Styled Polycast Wheel
Ornaments
[ER09200(ALL)12/95]
To remove a wheel ornament, insert the tapered end of the jack
handle between the ornament and wheel and pry the ornament
from the wheel.
[ER09300(ALL)12/95]
To install the polycast wheel center ornament, you should insert
one side of the ornament into the center of the wheel opening
and strike the opposite side with the palm of your hand until
the ornament is seated in the opening.
File:10cdero.ex
Update:Thu Sep 12 11:06:09 1996

177
Maintenance and Care
%*
[MC00200(ALL)01/96]
Service Made Easy
*
[MC00300(ALL)01/96]
Ford has two goals for servicing your vehicle.
*
[MC00400(ALL)01/96]1.
When we can, we design parts that do not need to be
serviced.
*
[MC00500(ALL)01/96]2.
We want to make servicing your vehicle as easy as possible.
To help you:
*
[MC00600(ALL)01/96]
n
We highlight do-it-yourself items in yellow in the engine
compartment so that you can find them easily.
*
[MC00700(ALL)03/96]
n
When possible, we design parts that can be replaced without
tools.
*
[MC00800(ALL)02/96]
n
We give you a Maintenance Schedule that makes tracking
routine service for your vehicle easy. The maintenance
schedule is located in theMaintenance Schedulebooklet.
*
[MC00900(ALL)01/96]
This chapter tells you about the basic parts that you need to
check and service regularly.
*
[MC01000(ALL)01/96]
If your vehicle needs professional servicing, your dealership can
provide the parts and service required. Check yourWarranty
Information Bookletto find out which parts and services are
covered. Also see theCustomer Assistancechapter of this Owner
Guide.
*
[MC01100(ALL)02/96]
Ford Motor Company recommends that the Owner Maintenance
Checks listed in theMaintenance Schedulebooklet be performed
for the proper operation of your vehicle. In addition to the
conditions listed in theOwner Maintenance Checklist, be alert for
any unusual noise, vibration, or other indication that your
vehicle may need service. If you do notice something unusual,
see that your vehicle is serviced promptly.
*
[MC01200(ALL)01/96]
Use only recommended fuels, lubricants, fluids, and service
parts conforming to Ford specifications. Motorcraft parts are
designed and built to provide the best performance in your
vehicle. Using these parts for replacement is your assurance that
Ford-built quality stays in your vehicle.
File:11cdmco.ex
Update:Thu Sep 12 11:08:18 1996

Maintenance and Care
179
*
[MC02200(ALL)01/96]
Working with the engine off:
[MC02300(ALL)12/95]1.
Set the parking brake fully and make sure that the gearshift
is securely latched in P (Park) (automatic transaxle) or 1
(First) gear (manual transaxle).
*
[MC02400(ALL)01/96]2.
Remove the key from the ignition after you turn the engine
off.
*
[MC02500(ALL)01/96]3.
Block the wheels. This will prevent your vehicle from
moving unexpectedly.
*
[MC02600(ALL)01/96]
Working with the engine on:
*
[MC02700(ALL)01/96]1.
Set the parking brake fully and make sure the gearshift is
securely latched in P (Park) (automatic transaxle) or Neutral
(manual transaxle).
*
[MC02800(ALL)01/96]2.
Block the wheels. This will prevent your vehicle from
moving unexpectedly.
*
[MC02900(ALL)01/96]
RWARNING
Do not start your engine with the air cleaner removed
and do not remove it while the engine is running.
*
[MC03000(ALL)12/95]
If the battery is disconnected, the computer must relearn its idle
control. SeeBatteryin the Index.
File:11cdmco.ex
Update:Thu Sep 12 11:08:18 1996