check engine FORD E SERIES 1996 4.G Owner's Guide

323 %
*
[SV33651( ALL)02/95]
Checking the Automatic Transmission
Fluid
*
[SV33701( ALL)05/95]
It is preferable to check the transmission fluid
level at normal operating temperature
150ÊF-170ÊF (66ÊC-77ÊC),after approximately 20
miles (30 km) of driving. However, if necessary,
you can check the fluid level without having to
drive 20 miles (30 km) to obtain a normal
operating temperature if outside temperatures
are above50ÊF (10ÊC).
*
[SV33801( ALL)01/95]
NOTE: If the vehicle has been operated for an
extended period at high speeds or in
city traffic during hot weather, or
pulling a trailer, the vehicle should be
turned off for about 30 minutes to
allow the fluid to cool before checking.
*
[SV33910( ALL)06/95]
With the vehicle on a level surface, start the
engine and move the transmission shift selector
through all of the gear ranges allowing sufficient
time for each position to engage. Securely latch
the transmission shift selector in the P (Park)
position, fully set the parking brake and leave
the engine running.
*
[SV33930( ALL)10/89]
RWARNING
Your vehicle should not be driven if the
fluid level is below the bottom hole on
the dipstick and outside temperatures are
above50ÊF (10ÊC).
*
[SV33940( ALL)02/95]
Wipe off the dipstick cap, pull the dipstick out
and wipe the indicator end clean. Put the
dipstick back into the filler tube and make sure
it is fully seated. Pull the dipstick out and read
the fluid level.
File:14ltsve.ex
Update:Wed Apr 17 08:40:13 1996

328
*
[SV37600( ALL)03/95]
Power Steering Fluid
*
[SV37700( ALL)01/95]
Check the level of the power steering fluid at
least twice a year (i.e., every Spring and Fall).
*
[SV37800( ALL)03/95]
To check the level of your power steering fluid:
*
[SV37900( ALL)02/95]
1. Start the engine and let it run until the
power steering fluid reaches normal
operating temperature. The power steering
fluid will be at the right temperature when
the engine coolant temperature gauge in the
instrument cluster is near the center of the
NORMAL operating temperature range.
*
[SV38000( ALL)01/95]
2. While the engine idles, turn the steering
wheel back and forth several times. Make
sure that the cap assembly is installed at this
time.
*
[SV38100(BEF )05/95]
3. Turn the engine off.
[SV38150( E)10/95]
All vehicles except E-Super Duty:
%*
[SV38200( ALL)03/94]
4. Check the fluid level on the dipstick (which
is highlighted in yellow in your vehicle). The
fluid level should be between the arrows in
the FULL HOT range, which is marked on
the side of the dipstick, opposite the side
marked FULL COLD. Do not add fluid if the
level is within the FULL HOT range.
File:14ltsve.ex
Update:Wed Apr 17 08:40:13 1996

331
*
[SV38900(BEF )01/95]
Use only power steering fluid that:
%*
[SV39000(BEF )01/95]
q
meets Ford's Specification, such as MerconH
Automatic Transmission Fluid.
*
[SV39200( ALL)01/95]
If the power steering fluid is low, do not drive
your vehicle for a long period of time before
adding fluid. This can damage the power
steering pump.
*
[SV39405( ALL)06/93]
NOTE: Do not turn the steering wheel of your
vehicle with the engine off. It could
force power steering fluid out from the
reservoir cap or in extreme cases, it
could unseat the cap.
*
[SV39500( ALL)04/95]
Fuses, Fuse Links and Circuit
Breakers
*
[SV39600( E )12/91]
Fuses and circuit breakers protect your vehicle's
electrical system from overloading. If electrical
parts in your vehicle are not working, the
system may have been overloaded and blown a
fuse or tripped a circuit breaker. Before you
replace or repair any electrical parts, check the
appropriate fuses or circuit breakers.
*
[SV39700( ALL)10/89]
The following charts tell you which fuses or
circuit breakers protect each electrical part of
your vehicle. If a fuse blows or a circuit breaker
opens a circuit, all the parts of your vehicle that
use that circuit will not work.
*
[SV39800( ALL)06/95]
Once you have determined which fuses or circuit
breakers to check, follow the procedures under
Checking and replacing fusesorChecking and
replacing circuit breakerslater in this chapter.
File:14ltsve.ex
Update:Wed Apr 17 08:40:13 1996

348
*
[SV49450( ALL)05/95]
If other than Ford or Motorcraft or Ford
authorized remanufactured parts are used for
maintenance, replacement, or for the service of
components affecting emissions control, the
owner should be assured that such parts are
warranted by their manufacturer to be
equivalent to genuine Ford Motor Company
parts in performance and durability. Please
consult your warranty information booklet for
complete warranty information.
*
[SV49500(BEF )05/95]
Watch for fluid leaks, strange odors, smoke, loss
of oil pressure, the charge warning light, the
check engine light, or the temperature warning
light. These sometimes indicate that the emission
system is not working properly.
*
[SV49600( ALL)01/95]
Do not make any unauthorized changes to your
vehicle or engine. Changes that cause more
unburned fuel to reach the exhaust system can
increase the temperature of the engine or
exhaust system.
*
[SV49700( ALL)01/95]
By law, anyone who manufactures, repairs,
services, sells, leases, trades vehicles, or
supervises a fleet of vehicles is not permitted to
intentionally remove an emission control device
or prevent it from working. In some of the
United States and in Canada, vehicle owners
may be liable if their emission control device is
removed or is prevented from working.
*
[SV49900( ALL)01/95]
Do not drive your vehicle if it does not operate
properly. See your dealer if the engine runs on
for more than five seconds after you shut it off
or if it misfires, surges, stalls, or backfires.
%*
[SV50000( ALL)05/95]
Information about your vehicle's emission
control system is on the Vehicle Emission
Control Information decal located on or near the
engine. This decal identifies engine displacement
and gives some tune-up specifications.
File:14ltsve.ex
Update:Wed Apr 17 08:40:13 1996

350
*
[SV50800( EFM)01/89]
The following are some of the acts that are
considered tampering:
[SV51000( E )01/89]
q
Removing the hood liner, fender apron
absorbers, fender apron barriers, under body
noise shield or material constructed to absorb
noise output.
*
[SV51100( EFM)01/89]
q
Removing or dismantling the engine speed
governor, so that the engine's speed exceeds
the manufacturer's specifications.
*
[SV51200( EFM)01/89]
q
Removing the air duct, air intake choke or
silencer, air cleaner and/or air cleaner
element.
*
[SV51300( EFM)01/89]
q
Removing or dismantling any of the exhaust
system components including the catalyst
inlet pipe, muffler, outlet pipe, resonator or
diffuser.
*
[SV51400( EFM)01/89]
q
Removing the fan shroud. Removing or
dismantling the fan clutch so that it no longer
functions properly.
*
[SV51450( EFM)04/89]
Maintenance
*
[SV51455( EFM)06/93]
Instructions for maintenance and service of the
noise control system have been included in the
Maintenance Schedule and Recordbooklet and in
the ªGeneral Maintenance Checklist.º To aid the
noise control system throughout the life of the
vehicle, Ford Motor Company recommends that
this vehicle should be operated according to the
Owner's Guide. When installing replacement
parts, use caution not to violate the tampering
act as described above. Use the Maintenance
Record Log to list any inspections and services
performed on the vehicle.
File:14ltsve.ex
Update:Wed Apr 17 08:40:13 1996

351 %
*
[SV51456( ALL)06/95]
Readiness for Inspection/Maintenance
Testing
*
[SV51457( ALL)06/95]
In some localities it may become a legal
requirement to pass an
Inspection/Maintenance (I/M) test of the
On-Board Diagnostic (OBD) II system. If the
vehicle's powertrain system or its battery has
just been serviced, the OBD II system is reset to
a not ready for I/M testing condition. To
prepare for I/M testing, the law specifies a
ªneed for additional mixed city and highway
driving to complete the checkº of the OBD II
system. As soon as all of the OBD II system
checks are successfully completed, the OBD II
system is set to the ready condition. The amount
of driving required to reach the ready condition
varies with individual driving patterns. To
complete this requirement in the minimum
amount of time, refer to the OBD II Drive Cycle
defined below. If the vehicle owner cannot or
does not want to do the additional driving
required by law, a service center can perform
this drive cycle as it would any other type of
repair work.
[SV51458( ALL)05/95]
OBD II Drive Cycle
*
[SV51459( ALL)05/95]
The engine must be warmed up and at
operating temperature before proceeding with
the drive modes of the following OBD II Drive
Cycle.
*
[SV51461( ALL)05/95]
1. Start the engine. Drive or idle (in neutral)
the vehicle for 4 minutes.
[SV51463( ALL)04/95]
2. Idle the vehicle in drive (neutral for manual
transmission) for 40 seconds.
*
[SV51465( ALL)06/95]
3. Accelerate the vehicle to 45 mph (70 km/h)
at 1/4 to 1/2 throttle for 10 seconds.
File:14ltsve.ex
Update:Wed Apr 17 08:40:13 1996

380 Index
Capacities for refilling fluids....... 353
Carbon monoxide in exhaust........ 65
Car seats for children
(see Child safety seats)......... 41
Cassette tape player
(see Electronic sound system) 164, 170, 178, 184
Catalytic converter............ 346
CD player (see Electronic sound system) . . 156
Chains, tires.............. 318
Changing a tire............. 247
Charging system gauge.......... 75
Charging system warning light....... 74
Child safety restraints........... 38
child safety belts............ 40
child safety seats............ 41
Child safety seats
and air bags.............. 41
attaching with tether straps....... 53
automatic locking mode (retractor).... 41
in front seat.............. 41
in rear outboard seat.......... 41
tether anchorage hardware........ 53
Chime
headlamps on.............. 77
key in ignition............. 56
safety belt............... 71
Circuit breakers
checking and replacing........ 339
see also fuses............. 331
Cleaning your vehicle
CD player and discs.......... 161
chrome and aluminum parts....... 10
engine compartment.......... 287
exterior................ 9
exterior lamps............. 93
fabric................ 141
headlamps............... 93
instrument panel lens.......... 97
interior lamps.............. 97
plastic parts.............. 10
polishing................ 9
File:ltixe.ex
Update:Wed Apr 17 08:36:26 1996

Index 381
Cleaning your vehicle (continued)
rustproofing.............. 10
safety belts............... 28
tail lamps............... 93
upholstery and interior trim...... 141
washing................ 9
wheels................ 319
Climate control system
air conditioning............ 87
heating................ 87
heating onlsystem............ 83
heating only system........... 83
Clock.............156, 173, 189
Cold engine starting............ 59
Combination lap and shoulder belts . . 11, 14
Compact disc player
(see Electronic sound system) . . . 150, 156
Compact disc radio
(see Electronic sound system)..... 150
Console, description........... 147
Controls
instrument panel............ 81
mirrors.............143, 146
power seat.............. 140
steering column............ 99
Coolant (see Engine coolant)....... 301
checking and adding......... 301
drain and flush............ 306
preparing for storage......... 362
proper solution............ 303
refill capacities............ 353
specifications............. 305
temperature gauge........... 78
Cooling fan............... 280
Crankcase emission filter......... 356
Cruise control (see Speed control).... 106
Customer Assistance Center, Ford (U.S.). . 261
Customer Assistance Centre,
Ford of Canada..........261, 268
File:ltixe.ex
Update:Wed Apr 17 08:36:26 1996

Index 383
Electronic stereo radio
(see Electronic sound system)..... 178
Emergencies, roadside
assistance.............. 259
battery acid spills.........243, 321
jump-starting............. 243
towing................ 258
Emergency brake (parking brake)..... 212
Emission control system......... 346
catalytic converter.......... 346
emissions warranty....... 4,346, 349
Engine
check engine warning light....... 71
diesel................. 6
fuel injected engine, starting..... 57,59
fuel pump shut-off switch........ 63
preparing to start............ 58
refill capacities............ 353
service points............ 283
starting.............. 55,59
starting after a collision......... 63
storing your vehicle........361±362
Engine block heater............ 62
Engine coolant
checking and adding......... 301
checking hoses............ 305
disposal...........301, 304, 324
drain and flush............ 306
preparing for storage......... 362
proper solution............ 303
recovery reservoir........283, 302
refill capacities............ 353
refill procedure............ 306
specifications............. 304
temperature gauge........... 78
Engine coolant temperature gauge..... 78
File:ltixe.ex
Update:Wed Apr 17 08:36:26 1996

384 Index
Engine fan............... 280
Engine knocking............. 290
Engine oil
changing oil and oil filter....... 300
checking and adding......... 298
dipstick............... 298
disposal...........301, 304, 324
engine oil pressure gauge........ 76
filter, specifications.......... 356
refill capacities............ 353
specifications............. 297
synthetic oil............. 297
ªbreak-inº oils............. 8
viscosity............... 297
Entry system
illuminated.............. 120
remote................ 116
Exhaust fumes.............. 65
Extended Service Plan, Ford........ 4
F
Fan, engine fan, avoiding injury..... 280
Federal Communications Commission . . . 192
Federal Highway Administration
Regulation............... 7
Flashers, hazard............. 103
Flashing the lights............ 101
Flat tire................. 247
Fluid refill capacities........... 353
Ford Customer Assistance Center..... 261
Ford Dispute Settlement Board...... 262
Ford Extended Service Plan........ 4
Ford Motor Company of Canada..... 268
Ford of Canada Customer
Assistance Centre........... 268
Foreign registration........... 267
Four-Wheel Drive vehicles, special notice . . 5
French owner guides, how to obtain.... 3
File:ltixe.ex
Update:Wed Apr 17 08:36:26 1996