reset FORD ESCORT 1996 7.G User Guide

213
%*
[AS21905(ALL)08/95]
Electronic Stereo and Stereo
Cassette Radios
*
[AS21910(ALL)08/95]
Using the Controls on Your New Radio
*
[AS21915(ALL)08/95]
How to turn the radio on and adjust the
volume
*
[AS21920(ALL)08/95]
Press the ªPOWERº button to turn the radio on.
Press it again to turn it off.
*
[AS22050(ALL)04/94]
Press the right (+) side of the ªVOLUMEº
button to increase the volume. Press the left (-)
side of the button to decrease the volume.
Illuminated bars in the display show the relative
volume level.
*
[AS22100(ALL)08/95]
Selecting the AM or FM frequency band
*
[AS22210(ALL)07/95]
Push the ªAM/FMº button to select the desired
frequency band. Pushing the button more than
once will alternate between AM, FM1 and FM2.
These functions are used with the station
memory buttons described underHow to tune
radio stations.
*
[AS22300(ALL)08/95]
How to tune radio stations (Stereo Radio)
*
[AS22400(ALL)08/95]
There are three ways for you to tune in to a
particular station. You can manually locate the
station by using the ªTUNEº button, ªSEEKº the
station or select the station by using the memory
preset buttons, which you can set to any desired
frequency.
File:09ctase.ex
Update:Tue Sep 19 14:51:59 1995

215
*
[AS22800(ALL)08/95]
q
Using the ªSEEKº function
*
[AS22900(ALL)08/95]
This feature on your radio allows you to
automatically select listenable stations up or
down the frequency band. Press the right
a
side of the ªSEEKº button to select the next
listenable station up the frequency band.
Press the left
bside of the button to select
the next listenable station down the
frequency band. By holding the button down,
listenable stations can be passed over to reach
the desired station.
*
[AS23120(ALL)08/95]
q
Using the ªSCANº function (Stereo Cassette
Radio)
*
[AS23150(ALL)08/95]
Press the ªSCANº button to enter the scan
mode. The radio will begin scanning up the
frequency band, stopping on each listenable
station for approximately a five-second
sampling. This continues until you press the
ªSCANº button a second time.
*
[AS23200(ALL)08/95]
q
Setting the Station Memory Preset buttons
*
[AS23300(ALL)05/95]
Your radio is equipped with 5 station
memory buttons. These buttons can be used
to select up to 5 preset AM stations and 10
preset FM stations (5 in FM1 and 5 in FM2).
*
[AS23400(ALL)08/95]
Follow the easy steps below to set these buttons
to the desired frequencies:
*
[AS23501(ALL)08/95]
1. Select a band, then select a frequency.
*
[AS23700(ALL)08/95]
2. Press one of the memory preset buttons and
hold the button until the sound returns. That
station is now held in memory on that
button.
*
[AS23800(ALL)08/95]
3. Follow the two steps above for each station
memory preset button you want to set.
File:09ctase.ex
Update:Tue Sep 19 14:51:59 1995

216
*
[AS23900(ALL)08/95]
NOTE: If the vehicle's battery is disconnected,
the clock and station memory preset
buttons will need to be reset.
*
[AS24000(ALL)08/95]
Adjusting the tone balance and speaker
output of your radio
*
[AS24100(ALL)08/95]
q
Increasing or decreasing bass response
[AS24250(ALL)06/95]
Push the ªAUDIOº button repeatedly until
the display reads ªBASS.º Push the ª+º side
of the ªVOLUMEº button to increase bass
(more ªlowsº), and push the ª-º side to
decrease bass (less ªlowsº).
*
[AS24300(ALL)08/95]
q
Increasing or decreasing treble response
[AS24450(ALL)06/95]
Push the ªAUDIOº button repeatedly until
the display reads ªTREB.º Push the ª+º side
of the ªVOLUMEº button to increase treble
(more ªhighsº), and push the ª-º side to
decrease treble (less ªhighsº).
*
[AS24500(ALL)08/95]
Speaker features and operation
*
[AS24600(ALL)08/95]
q
Adjusting speaker balance
[AS24750(ALL)06/95]
Balance control allows you to adjust the
sound distribution between the right and left
speakers. Push the ªAUDIOº button
repeatedly until the display reads ªBAL.º
Push the ª+º side of the ªVOLUMEº button
to shift the sound to the right speakers, and
push the ª-º side to shift the sound to the
left speakers.
*
[AS24800(ALL)08/95]
q
Adjusting speaker fader
[AS24950(ALL)06/95]
Fade control allows you to adjust the sound
distribution between the front and rear
speakers. Push the ªAUDIOº button
repeatedly until the display reads ªFADE.º
Push the ª+º side of the ªVOLUMEº button
to shift the sound to the front speakers, and
push the ª-º side to shift the sound to the
rear speakers.
File:09ctase.ex
Update:Tue Sep 19 14:51:59 1995

218
*
[AS27100(ALL)08/95]
How to eject the tape
*
[AS27250(ALL)08/95]
To stop the tape and eject the cassette, press the
ªEJECTº button. The radio will resume playing.
*
[AS27300(ALL)08/95]
Using the DolbyHB noise reduction feature
*
[AS27400(ALL)08/95]
NOTE: Noise reduction system manufactured
under license from Dolby Labs
Licensing Corporation. ªDolbyº and
double-D symbol are trademarks of
Dolby Laboratories Licensing
Corporation.
*
[AS27500(ALL)08/95]
Push thek/memory preset #3 button to
activate. Push again to deactivate.
%*
[AS27510(ALL)08/95]
Clock Operation
*
[AS27520(ALL)08/95]
How to view the clock mode
*
[AS27530(ALL)08/95]
Press the ªCLOCKº button to alternate the
frequency and time in the display. In the clock
mode, pressing any radio function will
automatically display the radio frequency for
approximately ten seconds before changing back
to the clock mode.
*
[AS27540(ALL)08/95]
How to set the clock
*
[AS27550(ALL)08/95]
1. Turn the radio on.
*
[AS27560(ALL)08/95]
2. Press and hold in the ªCLOCKº button,
press the ªSEEKº button left (
b) to advance
the hours and right (
a) to advance the
minutes.
*
[AS27570(ALL)08/95]
NOTE: The clock displays 12-hour time with
no AM/PM indications.
File:09ctase.ex
Update:Tue Sep 19 14:51:59 1995

256 [RE13200(ALL)06/93]
quarter page art:0070177-AAnti-theft lug nut and key
*
[RE13300(ALL)03/95]
Removing the anti-theft lug nut
*
[RE13500(ALL)03/95]
Insert the key over the locking lug nut. Make
sure that you hold the key square to the lug nut.
If you hold the key on an angle, you may
damage the key and the lug nut.
*
[RE13600(ALL)03/95]
Place the lug nut wrench over the lug nut key
and apply pressure on the key with the wrench.
Turn the wrench in a counterclockwise direction
to remove the lug nut.
*
[RE13650(ALL)09/95]
Reinstalling the anti-theft lug nut
*
[RE13700(ALL)03/95]
Insert the key over the locking lug nut. Place the
lug nut wrench over the lug nut key and, while
applying pressure on the key, install the lug nut.
*
[RE15100(ALL)12/91]
If the Engine Cranks but Does
Not Start or Starting After a
Collision
*
[RE15150(ALL)07/95]
The Fuel Pump Shut-off Switch
*
[RE15200(ALL)07/95]
If the engine cranks but does not start or if you
have had a collision, the fuel pump shut-off
switch may have been triggered. The shut-off
switch is a device that stops the fuel pump
when your vehicle has been involved in a
substantial jolt.
*
[RE15250(ALL)07/95]
For information on how to check and reset the
fuel pump shut-off switch, seeFuel pump shut-off
switchin the Index.
File:12ctree.ex
Update:Tue Sep 19 14:55:16 1995

313
%*
[SV29210(ALL)03/95]
Battery
[SV29220(ALL)03/95]
If the original equipment maintenance-free
battery is replaced, it may be replaced by a
low-maintenance battery. SeeMotorcraft Partsat
the end of this chapter for the proper
replacement battery.
*
[SV29230(ALL)03/95]
The low-maintenance battery has removable vent
caps for checking the electrolyte level and
adding water. The electrolyte level should be
checked at least every 24 months or 24,000 miles
(40,000 km) in temperatures up to90ÊF (32ÊC)
and more often in temperatures above90ÊF
(32ÊC). Keep the electrolyte level in each cell up
to the level indicator. Do not overfill.
*
[SV29240(ALL)03/95]
If the level gets low, refill the battery with
distilled water. If necessary, you can add tap
water to the battery, provided the water is not
hard or does not have a high mineral or alkali
content. If the battery needs water quite often,
have the charging system checked for a possible
malfunction.
[SV29245(ALL)03/95]
If you disconnect the battery, the engine must
ªrelearnº its idle conditions before your vehicle
will drive properly. To find out how the engine
does this, seeStarting your vehicle's fuel-injected
enginein the Index.
[SV29250(ALL)02/94]
If the battery has been disconnected, you will
have to reset the clock and the preset stations on
your radio once the battery is reconnected.
File:15ctsve.ex
Update:Tue Sep 19 14:37:50 1995

332 [SV34100(ALL)09/95]Even after you replace a fuse, it will continue to
blow if you do not find what caused the
overload. If the fuse continues to blow, have
your electrical system checked.
%*
[SV34300(ALL)03/95]
Circuit Breakers
[SV34425(ALL)08/95]
Circuit breakers open when a circuit overload
exceeds their rated current (amperage). The
manual reset-type used for the blower motor can
be reset by pushing the red button located on
top of the circuit breaker. If the overload which
caused the circuit breaker to open is still present
in the circuit, then the circuit breaker will open
again and the red button will pop out. The
overload must be removed from the circuit
before proceeding.
[SV34500(ALL)02/93]
The non-cycling type used for power seats,
power windows, and power door locks will stay
open once tripped until the overload is removed.
[SV34550(ALL)02/93]
The circuit breaker chart
[SV34560(ALL)08/95]
six pica chart:0070011-B*
[SV34570(ALL)08/95]
RWARNING
Always replace a fuse with one that has
the specified amperage rating. Using a
fuse with a higher amperage rating can
cause severe wire damage and could start
a fire.
File:15ctsve.ex
Update:Tue Sep 19 14:37:50 1995

343 %
*
[SV42405(ALL)07/95]
Readiness for Inspection/Maintenance
Testing
*
[SV42410(ALL)07/95]
In some localities it may become a legal
requirement to pass an
Inspection/Maintenance (I/M) test of the
On-Board Diagnostic (OBD) II system. If the
vehicle's powertrain system or its battery has
just been serviced, the OBD II system is reset to
a not ready for I/M testing condition. To
prepare for I/M testing, the law specifies a
ªneed for additional mixed city and highway
driving to complete the checkº of the OBD II
system. As soon as all of the OBD II system
checks are successfully completed, the OBD II
system is set to the ready condition. The amount
of driving required to reach the ready condition
varies with individual driving patterns. To
complete this requirement in the minimum
amount of time, refer to the OBD II Drive Cycle
defined below. If the vehicle owner cannot or
does not want to do the additional driving
required by law, a service center can perform
this drive cycle as it would any other type of
repair work.
[SV42415(ALL)09/95]
OBD II Drive Cycle (1.9L Engine only)
[SV42416(ALL)08/95]
The following steps must be run in the order
shown. If any steps are interrupted, repeat the
preceding step. Any safe driving mode is
acceptable between steps.
[SV42417(ALL)09/95]
NOTE: Always drive vehicle in a safe manner
according to traffic conditions and obey
all traffic laws.
File:15ctsve.ex
Update:Tue Sep 19 14:37:50 1995